Korg M3 Parameter Manual page 444

Effect Guide
"Bus Select DKit" is valid if you've selected a drum track for
a Timbre (Combination) or Track (Sequencer).
If you select DKit, the Bus Select (Global 5–4b) settings for
each key become effective, and each drum instrument sound
will be routed to the corresponding buses. At this time, the
actual send levels use these Send 1 and 2 values, multiplied
by the Send1 and 2 settings for each DrumKit key.
If a drum kit's Bus Select is set to L/R or Off, the levels will
be these Send 1 and 2 settings multiplied by the send levels
you specify in Program P8: Routing page for OSC1 Send1
(to MFX1) and Send2 (to MFX2) (Prog 8–1d), just as in other
cases (Oscillator Mode Single or Double).
If Bus Select is set to IFX1–5, use Send1 and Send2 for the
post-IFX signal. If Bus Select is set to 1–4, or 1/2, 3/4, the
Send 1 and 2 settings will be ignored.
Sampling mode
You can apply insert effects, master effects, and total effect to
an external audio source from the AUDIO INPUT 1, 2, or S/
P DIF IN jacks, and sample the result. You can also apply
insert effects, master effects, and total effect to samples
assigned to a multisample, and resample the result.
Use the P0– Audio Input page to make settings for external
audio sources from the AUDIO INPUT 1, 2, or S/P DIF IN
jacks.
The Bus Select setting for each jack specifies the bus to
which the external input source will be sent. You can choose
from L/R, IFX1–5, 1–4, 1/2, 3/4, or Off. If Bus Select is set to
L/R or Off, use Send1 (to MFX1) and Send2 (to MFX2) to
adjust the send levels to the master effects. If Bus Select is
set to IFX1–5, use the post-IFX Send1 and Send2 to adjust
the send levels to the master effects.
If you want to apply the master effects to the samples of a
multisample and play or resample the result, use the P8 -
Routing page settings Send1 (to MFX1) and Send2 (to
MFX2) or the P8– Insert FX Setup page settings post-IFX1–5
Send1 and Send2 settings to adjust the send levels to the
master effects.
Send1 can be controlled by receiving CC#93, and Send2
by receiving CC#91. These parameters are controlled on
the global MIDI channel (Global 1–1a).
Audio Input, S/P DIF IN, FireWire
In Program, Combination, Sequencer, and Media modes,
external audio sources from the AUDIO INPUT 1, 2, and S/
P DIF IN jacks can be processed by insert effects, master
effects, and total effect just as they can in Sampling mode.
In the P0– Sampling/Audio In page of each mode, the Use
Global Settings parameter makes settings for external input
from the AUDIO INPUT 1, 2, 3, 4, and S/P DIF IN jacks.
Set Bus Select to specify the bus to which the external audio
input will be sent. You can select L/R, IFX1–5, 1–4, 1/2, 3/4,
or Off. If Bus Select is set to L/R or Off, adjust the send
levels to the master effects using Send1 (to MFX1) and
Send2 (to MFX2). If Bus Select is set to IFX1–5, use the post-
434
IFX Send1 and Send2. If this is set to 1–4 or 1/2, 3/4, the
signal will not be sent to the master effects.
In Media mode, effects will use the settings of the mode
in which you previously were.
For details on the optional EXB-FW, please see "FireWire"
on page 429.