Korg M3 Parameter Manual page 17

0–6b: CCs/Notes Graphic
KARMA Module Info:
Module
This indicates module A.
CCs/Notes, Scan Zone
Module CCs Notes Scan Zone
This is a real-time display of the notes or CC# message
generated by the KARMA Module (Module [A]).
The Key Zone settings of the KARMA Module are displayed
as a solid blue line under the notes display. For more
information, please see "Zone:" on page 77.
KARMA Value
When you operate the KARMA Sliders 1–8 or KARMA
Switches 1–8, the number and value of the GE Real-Time
Parameters or Perf Real-Time Parameters you are
controlling will be displayed. This lets you see which
parameters are being controlled by the slider or switch, and
how.
Display example
Module & GE Name Selected Switch/Slider
Scene Chord Name Module ID
Module & GE Name
This shows the KARMA module and GE.
Scene
This shows the currently selected scene.
Chord Name
This shows the chord name detected by the KARMA
module.
Note: Chord detection is affected by the following
parameters.
• Prog 7–7–1: Program Select, Load GE Options, KARMA
T.Sig, Tempo, Key Zone
• Transpose (Prog 7–1–7: Module Parameter-Control)
• Destination (Prog 7–2–3: Dynamic MIDI) Chord Scan
and Smart Scan
Selected Switch/Slider
This shows the KARMA Sliders 1–8 or KARMA Switches 1–
8 you are currently operating or that was last selected.
Realtime Control Name
This shows the full name of the realtime control you are
currently operating or that was last selected. Parameter
assignments are made in the P7–1: KARMA2– Names page.
Module ID
This shows which parameters you are controlling from the
KARMA Sliders 1–8 or KARMA Switches 1–8.
A: Shows that KARMA Module A is being controlled. In this
case, you are controlling a GE Real-Time Parameter. (Note
that in Program mode, only Module A is available.) The
following number identifies the specific parameter within
the module. For instance, A22 is parameter 22 of Module A.
Realtime Control name
Parameter No. Parameter Value
[SW1...8, SL1...8]
[A, P]
PROG P0: Play 0–6: KARMA RTC
P: Shows that the slider or switch is controlling a
Performance Real-Time Parameter.
Parameter No.
When Module ID is A (KARMA Module A), this area shows
the GE Real-Time Parameter number 01–32 that you are
controlling (7–2: KARMA2– GE RTP). If Module ID is P, this
area shows the Performance Real-Time Parameter number
01–08 (7–2: KARMA2– Perf RTP) that you are controlling.
A slider or switch can have many parameters assigned to it.
A maximum of four assigned parameters can be displayed
here in the available space.
To change the parameter assignments, use the KARMA GE
RTP and Perf RTP pages. For more information, please see
7–2: KARMA– GE RTP page, and Perf RTP page.
Parameter Value
This shows the value of the GE or Performance Real-Time
Parameters assigned to the selected Slider or Switch. The
range can vary, depending on the individual parameters.
The range of the displayed value will depend on the
parameter. The display and value will change when you
operate the slider or switch.
Note: The number and value of the GE realtime parameters
and performance realtime parameters are shown as far as
can be displayed.
0–6c: RealTime Controls
This displays the names and stored settings of KARMA
Switches 1–8 and KARMA Sliders 1–8.
1, 2, 3, 4, 5, 6, 7, 8:
This shows the current settings of KARMA Switches 1–8
and the KARMA Sliders. The explanation below will
mention only Switch 1 and Slider 1. Switches 2–8 and Sliders
2–8 are the same as 1.
KARMA Switch1
This shows the current KARMA Switch 1 setting.
If Control Assign is KARMA, you can use the control
surface switches and sliders to control KARMA Switches 1–
8 and KARMA Sliders 1–8. You can also operate them by
directly pressing the switch shown in the display.
KARMA Switch1 Stored Value
This shows the setting of KARMA Switch 1 that is written
into the program.
KARMA Switch1 Name
This shows the name of KARMA Switch 1 (abbreviated
name).
You can assign this name in Prog 7–2: KRMA2 – Names.
KARMA Slider1
This shows the current setting of KARMA Slider 1.
If Control Assign is KARMA, this is linked with operations
of control surface slider 1. In addition, you can directly press
the slider shown in the display and then use the VALUE
slider, q/u switches, or VALUE dial to adjust the value.
KARMA Slider1 Stored Value
This shows the setting of KARMA Slider 1 that is written
into the program.
KARMA Slider1 Name
This shows the name of KARMA Slider 1 (abbreviated
name).
[01...32]
7