Korg M3 Parameter Manual page 104

Program mode
For more information, please see "Thru Out Z (Thru Out
Zone)" on page 78.
Transpose Octave In Thru
Assigns the Transpose In Zone (Prog 7–1–1b) function. This
controls the transposition of note data from the keyboard
within the Key Zone, in octave units.
Transpose Octave Out Thru
Assigns the Transpose Out Zone (Prog 7–1–1b) function.
This controls the transposition of note data from the
keyboard outside the Key Zone, in octave units.
Transpose Octave/5th In Thru
Assigns the Transpose In Zone (Prog 7–1–1b) function. This
controls the transposition of note data from the keyboard
within the Key Zone, in units of an octave and a fifth.
Transpose Octave/5th Out Thru
Assigns the Transpose Out Zone (Prog 7–1–1b) function.
This controls the transposition of note data from the
keyboard outside the Key Zone, in units of an octave and a
fifth.
Group: Random Seeds
Start Seed
Assign the Start Seed (Prog 7–1–6a) function.
+0000: Random
Other than +0000: Any desired Start Seed value. However,
you cannot select values outside the range of -8192 to +8191
when changing the value in this way.
For more information, please see "Start Seed" on page 82.
Note: If the Start Seed value is set to a value outside of this
range when you first assign it as a RT Parameter, it will be
limited to either end of the range.
Freeze Loop Length
Assigns the Freeze Loop Length (Prog 7–1–6a) function.
This specifies the number of measures (bars) in the phrases
that are repeatedly generated by the KARMA Module. After
being triggered, the Module will generate a phrase of the
number of measures you specify here, and will then repeat
that phrase.
For more information, please see "Freeze Loop Length" on
page 83.
Freeze Loop Length + Reset
Like Freeze Loop Length, above, this also assigns the Freeze
Loop Length (Prog 7–1–6a) function. However, when this is
used, and the Start Seed is set to some other value than 0:
Random, changing the Freeze Loop Length to any value
except 0: Off will reset the Start Seed internally to the
indicated value, thereby restoring the original phrase at the
next downbeat without retriggering it from the keyboard.
Normally, if you were generating a randomized riff from a
particular Start Seed value, setting Freeze Loop Length to 0:
Off would cause the phrase to continue randomizing from
its current internal position. If you then set the Freeze Loop
Length to some other value than 0: Off, thereby looping the
phrase, it does not automatically reset the Start Seed until
you retrigger it from the keyboard (depending on Trigger
settings). By using Freeze Loop Length + Reset, a change in
the Freeze Loop Length can additionally reset the internal
Start Seed and therefore generate the same phrase as before,
allowing instantaneous switching between "randomized"
and "preset" phrases.
94
[–0036...+0036]
[–0036...+0036]
[–0036...+0036]
[–0036...+0036]
[–8192...+0000...+8191]
[+0000...+0032]
[+0000...+0032]
Retrigger Each Time
Assigns the Retrigger Each Time (Prog 7–1–6a) function.
+0000: Off
+0001: On
For more information, please see "Retrigger Each Time" on
page 83.
▼7–2–2: Menu Command
• 0: Write Program ☞p.106
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy KARMA Module ☞p.114
• 4: Initialize KARMA Module ☞p.115
• 5: Copy Scene ☞p.115
• 6: Swap Scene ☞p.115
• 7: Capture Random Seed ☞p.116
For more information, please see "Program: Menu
Command" on page 106.
[+0000, +0001]