Korg M3 Parameter Manual page 397

Reset Controller MIDI Assign
This automatically assigns the MIDI control change
messages for each controller of the P2: Controllers– MIDI
CC# Assign page.
1. Select "Reset Controller MIDI Assign" to open the dia-
log box.
2. Set the To field to the desired reset method.
All Off: All settings will be Off.
Default Setting: The KARMA controls and pads will all be
set to Off; the X–Y control will be set to its default CCs.
CC Default: The parameters will be reset to the typical
settings, including the standard settings for the pads and the
KARMA sliders and switches.
If you want to record KARMA controllers in Sequencer
mode, or use the controllers to control an external MIDI
device, we recommend using this setting.
(You are also free to assign different MIDI control change
messages to the controllers, if you wish.)
The default values are shown in the table below.
3. Press the OK button to execute the reset command, or
press the Cancel button to cancel.
Reset Controller MIDI Assign Default
Controllers \ to
On/Off
Latch
Scene
SW 1
SW 2
SW 3
SW 4
SW 5
SW 6
KARMA Controllers SW 7
SW 8
Slider 1
Slider 2
Slider 3
Slider 4
Slider 5
Slider 6
Slider 7
Slider 8
X (X–Y MODE)
X–Y
Y (X–Y MODE)
Pad 1
Pad 2
Pad 3
Pad 4
Pads (CC and Note)
Pad 5
Pad 6
Pad 7
Pad 8
Default Setting CC Default
Off (CC#14)
Off (CC#31)
Off (CC#30)
Off (CC#102)
Off (CC#103)
Off (CC#104)
Off (CC#105)
Off (CC#106)
Off (CC#107)
Off (CC#108)
Off (CC#109)
Off (CC#22)
Off (CC#23)
Off (CC#24)
Off (CC#25)
Off (CC#26)
Off (CC#27)
Off (CC#28)
Off (CC#29)
(CC#118) (CC#118)
(CC#119) (CC#119)
Off (CC#110)
Off (CC#111)
Off (CC#112)
Off (CC#113)
Off (CC#114)
Off (CC#115)
Off (CC#116)
Off (CC#117)
Global: Menu Command Reset Controller MIDI Assign
Copy Scale
This command copies data from a preset scale or between
user scales. For details on the preset scales, please see Type
(Prog 1–2b).
1. Select "Copy Scale" to open the dialog box.
2. Use From to select the copy-source scale.
If you select Pure Major or Pure Minor, specify the Key
(located at the right) as well.
Stretch cannot be selected if To is User All Notes Scale.
3. In To, selects the copy destination scale.
4. To execute the Copy Scale command, press the OK but-
ton. To cancel, press the Cancel button.
Write Drum Kits
This saves all drum kits 000 (INT)–143 (U–G).
You must write an edited drum kit if you want to keep it.
Edited drum kits cannot be recovered if you turn off the
power before saving them.
1. Select "Write Drum Kits" to open the dialog box.
2. Press the OK button to execute the Write Drum Kit
command, or press the Cancel button to cancel without
executing.
Note: You can also use the SEQUENCER REC/WRITE
switch to write in the same way as the Write Drum Kit
command. Press the SEQUENCER REC/WRITE switch to
access the Update Drum Kit dialog box, and write the drum
kit. In this case, the data will be written to the currently
selected drum kit.
Rename Drum Kit
This renames a drum kit.
For more information, please see "Editing names" on
page 197 of the Operation Guide.
387