Siemens SINUMERIK 840D sl Programming Manual page 6

Table of contents
2.14.3.6 Displaying a user log in the form of a measurement results screen......................................70
2.14.3.7 Behavior during block search, simulation and for several channels......................................72
3 Measuring variants.....................................................................................................................................73
3.1 General requirements............................................................................................................73
3.1.1 Overview of the measuring cycles.........................................................................................73
3.1.2 Selection of the measuring variants via softkeys (turning).....................................................75
3.1.3 Selection of the measuring variants via softkeys (milling)......................................................78
3.1.4 Result parameters..................................................................................................................80
3.2 Measure workpiece (turning)..................................................................................................81
3.2.1 General information................................................................................................................81
3.2.2 Calibrate probe - length (CYCLE973)....................................................................................82
3.2.3 Calibrate probe - radius on surface (CYCLE973)..................................................................85
3.2.4 Calibrate probe - calibrate in groove (CYCLE973).................................................................88
3.2.5 Turning measurement - front edge (CYCLE974)...................................................................92
3.2.6 Turning measurement - inside diameter (CYCLE974, CYCLE994).......................................95
3.2.7 Turning measurement - outside diameter (CYCLE974, CYCLE994).....................................99
3.2.8 Extended measurement.......................................................................................................105
3.3 Measure workpiece (milling)................................................................................................107
3.3.1 General information..............................................................................................................107
3.3.2 Calibrate probe - length (CYCLE976)..................................................................................108
3.3.2.1 Function...............................................................................................................................108
3.3.2.2 Calling the measuring version..............................................................................................110
3.3.2.3 Parameters...........................................................................................................................110
3.3.2.4 Result parameters................................................................................................................112
3.3.3 Calibrate probe - radius in ring (CYCLE976).......................................................................112
3.3.4 Calibrate probe - radius on edge (CYCLE976)....................................................................117
3.3.5 Calibrate probe - radius between 2 edges (Cycle976).........................................................120
3.3.5.1 Function...............................................................................................................................120
3.3.5.2 Calling the measuring version..............................................................................................122
3.3.5.3 Result parameters................................................................................................................124
3.3.6 Calibrate probe - calibrate on ball (CYCLE976)...................................................................124
3.3.7 Edge distance - set edge (CYCLE978)...............................................................................128
3.3.8 Edge distance - align edge (CYCLE998).............................................................................134
3.3.9 Edge distance - groove (CYCLE977)...................................................................................141
3.3.10 Edge distance - rib (CYCLE977)..........................................................................................146
3.3.11 Corner - right-angled corner (CYCLE961)...........................................................................152
3.3.12 Corner - any corner (CYCLE961).........................................................................................157
3.3.13 Hole - rectangular pocket (CYCLE977)................................................................................163
3.3.14 Hole - 1 hole (CYCLE977)...................................................................................................168
3.3.15 Hole - inner circle segment (CYCLE979).............................................................................173
3.3.16 Spigot - rectangular spigot (CYCLE977)..............................................................................179
3.3.17 Spigot - 1 circular spigot (CYCLE977).................................................................................184
3.3.18 Spigot - outer circle segment (CYCLE979)..........................................................................190
3.3.19 3D - align plane (CYCLE998)...............................................................................................195
3.3.20 3D - sphere (CYCLE997).....................................................................................................200
3.3.21 3D - 3 spheres (CYCLE997)................................................................................................205
3.3.22 3D - angular deviation spindle (CYCLE995)........................................................................210
3.3.23 3D - kinematics (CYCLE996)...............................................................................................214
3.3.24 Expanded functionality CYCLE996......................................................................................232
3.3.24.1 Checking the sphere diameter.............................................................................................232
6
Programming Manual, 12/2017, 6FC5398-4BP40-6BA1
Measuring cycles