Siemens SINUMERIK 880 Programming Manual page 284

13 Program Key SINUMERIK 880/880 GA2
13.4 Program key for version M
G
EIA ISO
gr.
22 g G (203)
(204)
(204)
2) 2)
x X ±0.001 to ±99999.999
±0.0001 to ±3937.000
0.001 to 99999.999
±0.001° to ±99999.999°
2) 2)
y Y ±0.001 to ±99999.999
±0.0001 to ±3937.000
±0.001° to ±99999.999°
2) 2)
z Z ±0.001 to ±99999.999
±0.0001 to ±3937.000
±0.001° to ±99999.999°
2) 2)
4. 4. ±0.001 to ±99999.999
±0.0001 to ±3937.000
±0.001° to ±99999.999°
3) 3)
a A 0 to 359.99999°
0 to 359.99999°
3) 3)
b B 0.001 to 99999.999
0.0001 to 3937.000
0
– 0.001 to – 99999.999
– 0.0001 to –3937.000
0.001 to 99999.999
0.0001 to 3937.000
i I ±0.001 to ± 99999.999
±0.0001 to ±3937.000
0.001 to 2000.000
0.0001 to
j J ±0.001 to ± 99999.999
±0.0001 to ±3937.000
0.001 to 2000.000
0.0001 to
k K ±0.001 to ± 99999.999
±0.0001 to ±3937.000
0.001 to 2000.000
0.0001 to
1) No further functions must be written in this block
2) Extended address possible (e.g. S1=.., M6=.., ..., see Section 2.4)
3) Other addresses are selectable (A, B, C, E, U, V, W and Q)
4) G80 to G89 cannot be used in the 3rd subroutine level
5) The stated values depend on the input and position control resolution (see Section 12)
# Effective block by block, all other modal
* Reset position (basic position after reset, MO2/M30, after switching on the control)
( ) Applies to SINUMERIK 880 GA2 only
13–14
Code
Select C axis operation, clockwise
Select C axis operation, counter-clockwise
Change from C axis operation to spindle operation
Positional data in mm
Positional data in inch
Dwell in s
Positional data in degrees
Positional data in mm
Positional data in inch
Positional data in degrees
Positional data in mm
Positional data in inch
Positional data in degrees
Positional data in mm
Positional data in inch
Positional data in degrees
Possible addresses, A, B, C, E, U, V, W, Q with or
without address extension
Angle in degrees with contour definition
Angle in degrees with polar coordinates
Radius with circular interpolation and polar
coordinates in mm
Radius with circular interpolation and polar
coordinates in inch
Corner with contour definition
Chamfer with contour def. in mm
Chamfer with contour def. in inch
Radius with contour def. in mm
Radius with contour def. in inch
Interpolation parameter for X axis in mm
Interpolation parameter for X axis in inch
Thread lead in mm (depending on input resolution)
80.000 Thread lead in inch (depending on input resolution)
Interpolation parameter for Y axis in mm
Interpolation parameter for Y axis in inch
Thread lead in mm (depending on input resolution)
80.000 Thread lead in inch (depending on input resolution)
Interpolation parameter for Z axis in mm
Interpolation parameter for Z axis in inch
Thread lead in mm (depending on input resolution)
80.000 Thread lead in inch (depending on input resolution)
© Siemens AG 1991 All Rights Reserved
Function and meaning
6ZB5 410-0HD02
SINUMERIK 880, (PG)
01.93
Sect.
4.3.5
4.3.5
4.3.5
4.1
4.1
4.2.8
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
8
4.2.5
4.2.2
4.2.2
8.2
8.2
8.2
8.2
8.2
4.2.2.1
4.2.2.1
4.3.1
4.3.1
4.2.2.1
4.2.2.1
4.2.7
4.2.7
4.2.2.1
4.2.2.1
4.3.1
4.3.1