Siemens SINUMERIK 880 Programming Manual page 283

01.93
G
EIA ISO
gr.
12 g G 147 #
247 #
347 #
148 #
248 #
348 #
48 #
110 #
111 #
13 g G 51
50
14 g G 150 *
151
152
153
154
155
156
157
158
159
15 g G
130
131
133
135
16 g G
230
231
233
235
17 g G
330
331
333
335
19 g G 201
202
(20) g G (171)
21 g G 175 *
176
1) No further functions must be written in this block
2) Extended address possible (e.g. S1=.., M6=.., ..., see Section 2.4)
3) Other addresses are selectable (A, B, C, E, U, V, W and Q)
4) G80 to G89 cannot be used in the 3rd subroutine level
5) The stated values depend on the input and position control resolution (see Section 12)
# Effective block by block, all other modal
* Reset position (basic position after reset, MO2/M30, after switching on the control)
( ) Applies to SINUMERIK 880 GA2 only
© Siemens AG 1991 All Rights Reserved
SINUMERIK 880, (PG)
Code
1)
Approach contour with straight line
1) Approach contour with quadrant
1)
Approach contour with semi-circle
1)
Exit with straight line
1)
Exit with quadrant
1)
Exit with semi-circle
1)
Exit as approach
Polar coordinate programming,
Adopt last programmed position as new centre point
Polar coordinate programming, pole programming with
angle and radius
1)
Scale modification
1)
Deselection of scale modification
Deselection of coupled motion
Coupled axis combination 1
Coupled axis combination 2
Coupled axis combination 3
Coupled axis combination 4
Coupled axis combination 5
Coupled axis combination 6
Coupled axis combination 7
Coupled axis combination 8
Coupled axis combination 9
PAIRING 1
1)
Deselection of transformation TRANSMIT or
Deselection of transformation coordinate rotation 2D/3D
1) Transformation TRANSMIT
Transformation coordinate rotation 2D
Transformation coordinate rotation 3D
PAIRING 2
1)
Deselection of transformation TRANSMIT or
Deselection of transformation coordinate rotation 2D/3D
1) Transformation TRANSMIT
Transformation coordinate rotation 2D
Transformation coordinate rotation 3D
PAIRING 3
1)
Deselection of transformation TRANSMIT or
Deselection of transformation coordinate rotation 2D/3D
1) Transformation TRANSMIT
Transformation coordinate rotation 2D
Transformation coordinate rotation 3D
Selection of synchronous spindle
Deselection of synchronous spindle
Fill FIFO buffer
ZO, length compensation, angle of rotation update in each
block
Freeze length compensation/zero offsets/angle of rotation
6ZB5 410-0HD02
13 Program Key SINUMERIK 880/880 GA2
13.4 Program key for version M
Function and meaning
Sect.
4.2.9
4.2.9
4.2.9
4.2.9
4.2.9
4.2.9
4.2.9
4.2.5
4.2.5
3.11
3.11
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.13
4.2.12/
4.2.13
4.2.12
4.2.13
4.2.13
4.2.12/
4.2.13
4.2.12
4.2.13
4.2.13
4.2.12/
4.2.13
4.2.12
4.2.13
4.2.13
4.2.19
4.2.19
5.7
4.2.14
4.2.14
13–13