Siemens SINUMERIK 880 Programming Manual page 279

01.93
G
EIA ISO
gr.
k K ±0.001 to ± 99999.999
±0.0001 to ±3937.000
0.001 to 2000.000
0.0001 to
5) 5)
f F 0.001 to 45
0.01 to
0.1
0.001 to 99.999
0.001 to 50.000
0.0001 to 2.0000
0.001 to 16.000
0.0001 to 0.6000
2) 2)
s S 16-bit servo CPU
1
1
0.1 to
0.1 to
2) 2)
s S 32-bit servo CPU with
actual value acquisition
1
1
0.1 to
0.1 to
2) 2)
s S 32-bit servo CPU without
actual value acquisition
1
1
—
0.1 to
t T 1 to 99999999
h H 1 to 99999999
l L 1 to 999
p P 1 to 9999
d D 1 to 204 (409)
0
1) No further functions must be written in this block
2) Extended address possible (e.g. S1=.., M6=.., ..., see Section 2.4)
3) Other addresses are selectable (A, B, C, E, U, V, W and Q)
4) G80 to G89 cannot be used in the 3rd subroutine level
5) The stated values depend on the input and position control resolution (see Section 12)
# Effective block by block, all other modal
* Reset position (basic position after reset, MO2/M30, after switching on the control)
( ) Applies to SINUMERIK 880 GA2 only
© Siemens AG 1991 All Rights Reserved
SINUMERIK 880, (PG)
Code
Interpolation parameter for Z axis in mm
Interpolation parameter for Z axis in inch
Thread lead in mm (depending on input resolution)
80.000 Thread lead in inch (depending on input resolution)
Feedrate in m/min (machine data)
45000 Feedrate in mm/min
to 1770.0000 Feedrate in inch/min
Dwell in s
Feedrate in mm/rev
Feedrate in inch/rev
Thread, lead increase or decrease in mm/rev
Thread, lead increase or decrease in inch/rev
to 16000 Spindle speed in rev/min or 0.1 rev/min and constant
cutting speed in m/min or 0.1 m/min or
ft/min or 0.1 ft/min
to 16000 Spindle speed limitation in rev/min or 0.1 rev/min
Spindle stop in degrees, distance from the zero mark of
359.9
the encoder
Dwell in spindle revolutions
99.9
to 30000 Spindle speed in rev/min or in 0.1 rev/min and constant
cutting speed in m/min or 0.1m/min or ft/min or
0.1 ft/min
to 30000 Spindle speed limitation in rev/min or 0.1 rev/min
359.99 Spindle stop in degrees, distance form zero mark of
encoder
99.9 Dwell time in spindle revolutions
to 99999 Spindle speed in rev/min or in 0.1 rev/min and constant
cutting speed in m/min or 0.1m/min or ft/min or
0.1 ft/min
to 99999 Spindle speed limitation in rev/min or 0.1 rev/min
to — Spindle stop in degrees, distance form zero mark of
encoder
99.9 Dwell time in spindle revolutions
2)
Tool number
2)
Auxiliary function
Subroutine number
Number of passes of subroutine
Selection of tool offset
Deselection of tool offset
6ZB5 410-0HD02
13 Program Key, SINUMERIK 880/880 GA2
13.3 Program key for version T
Function and meaning
Sect.
4.2.2.1
4.2.2.1
4.2.7
4.2.7
4.2.6
4.2.6
4.2.6
4.2.8
4.2.6
4.2.6
4.3
4.3
5.2
5.2
5.2
4.2.8
5.2
5.2
5.2
4.2.8
5.2
5.2
5.2
4.2.8
5.5
5.4
6
5.3
9.1
9.1/10.3
13–9