Siemens SINUMERIK 880 Programming Manual page 276

13 Program Key, SINUMERIK 880/880 GA2
13.3 Program key for version T
G
EIA ISO
gr.
6 g G 04 #
25
26
58
59
92
74
200
7 g G 60
62
63
64 *
8 g G 70
71
9 g G 80
81
82
83
84
85
86
87
88
89
10 g G 68
90 *
91
11 g G 94
95 *
96
97
195
1
) No further functions must be written in this block
2) Extended address possible (e.g. S1=.., M6=.., ..., see Section 2.4)
3) Other addresses are selectable (A, B, C, E, U, V, W and Q)
4) G80 to G89 cannot be used in the 3rd subroutine level
5) The stated values depend on the input and position control resolution (see Section 12)
# Effective block by block, all other modal
* Reset position (basic position after reset, MO2/M30, after switching on the control)
( ) Applies to SINUMERIK 880 GA2 only
13–6
Code
1)
Dwell time, specified under address X or F in seconds and
address S in spindle revolutions
1)
Minimum working area limitation
1)
Maximum working area limitation/
spindle speed limitation S
1) Programmable zero offset 1
1)
Programmable zero offset 2
1)
Spindle speed setpoint limitation under address S (acts
only with "G96 active")
Feedrate run-up and smoothing time under address T
Cylindrical interpolation, ratio between working and unit
diameter under address P
1) Reference point approach by program
Axis synchronization with change of channel
Speed reduction, exact stop fine
Contouring mode, block transition with speed reduction
Tapping without encoder, feedrate override 100 %
Continuous path control mode, block transition without
speed reduction
Input system inch
Input system metric
4)
Deselection of G81 to G89
4)
Call cycle L81: Drilling, centering
4) Call cycle L82: Drilling, spot facing
4)
Call cycle L83: Deep-hole drilling
4)
Call cycle L84: Tapping with/without encoder
4)
Call cycle L85: Boring 1
4)
Call cycle L86: Boring 2
4)
Call cycle L87: Boring 3
4)
Call cycle L88: Boring 4
4)
Call cycle L89: Boring 5
Absolute dimensioning along shortest path (rotary axis
only)
Absolute dimensioning
Incremental dimensioning
Feedrate under address F in mm/min or inch/min
Feedrate under address F in mm/rev or inch/rev
Feedrate under address F in mm/rev or inch/rev and
constant cutting speed under address S in m/min or ft/min
Cancel G96, store last set speed
Feedrate in mm/rev referred to rotary axis
© Siemens AG 1991 All Rights Reserved
Function and meaning
(Reset position via machine data)
(Reset position via machine data)
6ZB5 410-0HD02
SINUMERIK 880, (PG)
01.93
Sect.
4.2.8
3.9
3.9
5.3
3.5
3.5
5.3
4.4.4
4.2.4
3.12
4.2.16
4.2.7
4.2.7.2
4.3.4
4.2.7.2
3.7
3.7
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
4.1
3.3
3.3
4.2.6
4.2.6
4.2.6
4.2.6
4.2.6