Factory Default Settings; Wiring Guide For Rs-232 Data Transmission; Firmware Release Notes - Lightware HDMI-TPS-TX210 User Manual

   
11.Appendix
11.4. Factory Default Settings
Parameter
Crosspoint settings (for SW4-TPS-TX240)
Video
Audio
Video input port settings (HDMI, DVI-D, DP)
HDCP
Emulated EDID
Video output port settings (TPS, HDMI)
Autoselect
Test pattern mode
Test pattern resolution
Test pattern
Signaltype
HDCPmode
Power5Vmode
TPSmode
Analog audio input port settings
Volume
Balance
Gain
Network settings
IPaddress
Subnetmask
Staticgateway
DHCP
LW2portnumber
LW3portnumber
HTTPportnumber
RS-232 settings
Control protocol
Baud rate
Databits
Parity
Stopbits
Setting/Value
Operation mode
Commandinjectionstatus
I1(DPin)
Commandinjectionportno.-Local
I1(DPin)
Commandinjectionportno.-TPS
Enabled
Commandinjectionstatus
Dynamic#1:TheEDIDofthe
Comm.inj.inputportno.-Local
connected sink device.
Comm.inj.outputportno.-Local
Comm.inj.inputportno.-TPS
Disabled
Comm.inj.outputportno.-TPS
Off
640x480p
Direction
Bar
Output level
Auto
Auto
11.5. Wiring Guide for RS-232 Data Transmission
Always on
Thestandalonetransmittersarebuiltwith3-polePhoenixconnector.
Auto
Seetheexamplesbelowofthemostcommonconnectingcases.
Matrix and a DCE (Data Circuit-
0.00 dB
terminating Equipment)
50(center)
0 dB
192.168.0.100
255.255.255.0
192.168.0.1
Disabled
10001
6107
80
LW2
57600
8
None
Appliedfirmwarepackage:v1.2.0 | LDCsoftware:v2.2.0
HDMI-TPS-TX200series–User'sManual
Parameter Setting/Value
1
Pass-through
Enabled
8001
8002
IR port settings
Enabled
9001
9002
9003
9004
GPIO port settings
Input
High
Matrix and a DTE (Data Terminal
Equipment)
D-SUB 9 and Phoenix D-SUB 9 and Phoenix
TX RX TX RX
5 1
1
9 6
6
2: TX data 2: RX data
3: RX data 3: TX data
5: Ground 5: Ground
#factory
11.6. Firmware Release Notes
Below list shows the released firmware packages with important
notes.
v1.2.0b16
Releasedate:2019-08-15
New feature:
▪ CompatibleforLDU2only!
▪ ModifiedDPinputdrivertofixHDCPissuewithMacBooks
▪ UseLDU2v1.2.5orlaterfortheupgrade!
▪ CEC-sendCECcommand(e.g.turnontheTVwithEventActions)
forSW4-TPS-TX240-Plusonly!
▪ RS232MinimalRecognizerforCiscocompatibility(CiscoLogin)
forSW4-TPS-TX240-Plusonly!
▪ Sending IR codes (SendProntoHex e.g. send max. 200 Byte IR
codewithEventActions)forSW4-TPS-TX240-Plusonly!
▪ Modified RS-232 modes to support SendMessage in Control
mode
▪ Added'Forcedbuttonlock'functiontolockbuttonsviaprotocol
command
▪ Firmware platform library updated
▪ Added'Darkmode'functiontoturnofffrontpanelLEDs
▪ ImprovedGPIOdetection
▪ Added'Disabledefaultbuttonfunction'optiontosupportbutton
customizationinEventManager
▪ Added'Userreplaceableminiwebslot'tosupportbuilt-incontrol
webpage
Bugfix:
▪ TheproblemwithHDCPLEDlightingonTPSlinkwasfixed.
▪ ProblemwithEEPROMproductiontestwasfixed.
5
9
114