Unlockoutput; Viewconnectionstateontheoutput; Viewcrosspointsize; Changevideoautoselectmode - Lightware HDMI-TPS-TX210 User Manual

   
6.LW2Programmer'sReference
6.4.5. Unlock Output
Unlockinganoutputport.Theconnectiononoutputcanbechanged.
Command and Response
 {+<<out>•<layer>}
 (0LO<out2>•<layer>)CrLf
Example
 {+<01V}
 (0LO01V)
O1videooutputportisunlocked.
INFO:
Thedeviceissuestheaboveresponseregardlessofthepreviousstateoftheoutput(eitheritwas
locked or unlocked).
6.4.6. View Connection State on the Output
Viewingthecrosspointstateofthedevice;showingtheinputportnumbersconnectedtotheoutputs.
Command and Response #crosspoint
 {VC•<layer>}
 (ALL<layer>•<O01>•<O02>)CrLf
Parameters
O01showsthecorrespondingoutput'sconnectionstate.
Identifier Parameterdescription
<layer> Signaltypeofthelayer
State letters
Letter
L Output is locked
M Output is muted
U Output is locked and muted
Example
 {VCAV}
 (ALLVM0101)
 (ALLA0101)
I2videoinputportisconnectedtothevideooutputportandI5audioinputportisconnectedtotheaudio
outputport.AVisnotusedintheresponse.WhenAVistypedinthecommands,theresponsewillresulttwo
lines,onefortheVideoandonefortheAudioportstates.
#switch
Parametervalues
A: audio layer
V: video layer
AV:audio&videolayer
State Example
L01
M01
U01
Appliedfirmwarepackage:v1.2.0 | LDCsoftware:v2.2.0
HDMI-TPS-TX200series–User'sManual
6.4.7. View Crosspoint Size
Showsthephysicalcrosspointsize.
Command and Response
 {getsize•<layer>}
 (SIZE=<size>•<layer>)CrLf
Parameters
Identifier
<size>
<layer>
Example
 {GETSIZEAV}
 (SIZE=6x1V)
 (SIZE=5x1A)
Thedevicereportsthatithasavideocrosspointwith6inputs(Testpatterngeneratoristhe6thinput)and1
outputandanaudiocrosspointwith5inputsand1output.
6.4.8. Change the Video Autoselect Mode
Theautoselectmodeofthevideooutputscanbechanged.
Command and Response
 {AS_V<out>=<state>;<mode>}
 (AS_V<out>=<state>;<mode>)CrLf
Parameters
Identifier
<state>
<mode>
Example
 {as_v1=E;P}
 (AS_V1=E;P)
 (AS_V2=E;P)
TheAutoselectmodeofvideooutput1andoutput2isenabledandsettoPrioritymode.Theoutputnumbers
are listed in the PortNumbering
INFO:
TheAutoselectmodecanbequeriedbytypingthe{as_v<out>=?}command.
Parameterdescription Parametervalues
Crosspointsize <number_of_inputs>x<number_of_outputs>
Signaltypeofthelayer Seetheprevioussection
Parameterdescription Parametervalues
ShowingtheAutoselectstate E: autoselect is enabled
D: autoselect is disabled
Theautoselectmodesetting F: First detect mode
L:Lastdetectmode
P:Prioritydetectmode
section.
61