Lightware HDMI-TPS-TX210 User Manual page 95

   
7.LW3Programmer'sReference
SettingaStaticIPAddress
SET·/MANAGEMENT/NETWORK.StaticIpAddress=<IP_address>

QueryingtheSubnetMask
 GET·/MANAGEMENT/NETWORK.NetworkMask
SettingaStaticSubnetMask
SET·/MANAGEMENT/NETWORK.StaticNetworkMask=<subnet_mask>

QueryingtheGatewayAddress
 GET·/MANAGEMENT/NETWORK.GatewayAddress
SettingaStaticGatewayAddress
SET·/MANAGEMENT/NETWORK.StaticGatewayAddress=<gateway_address>

RS-232 Port Configuration
ProtocolSetting
SET·/MEDIA/UART/<port>.ControlProtocol=<protocol>

BAUDRateSetting
SET·/MEDIA/UART/<port>.BaudRate=<baud_rate>

DatabitSetting
SET·/MEDIA/UART/<port>.DataBits=<data_bits>

StopbitSetting
SET·/MEDIA/UART/<port>.StopBits=<stop_bits>

ParitySetting
SET·/MEDIA/UART/<port>.Parity=<parity_value>

RS-232OperationMode
SET·/MEDIA/UART/<port>.Rs232Mode=<mode>

CommandInjectionMode
SET·/MEDIA/UART/<port>.CommandInjectionEnable=<CI_set>

Infrared Port
EnableCommandInjectionMode
SET·/MEDIA/IR/<port>.CommandInjectionEnable=<CI_set>

Enable/DisableOutputSignalModulation
SET·/MEDIA/IR/<out>.EnableModulation=<mod_set>

SendingProntoHexCodesinLittle-endianFormatviaIRPort
 CALL·/MEDIA/IR/D1:sendProntoHex(<hex_code>)
HDMI-TPS-TX200series–User'sManual
Message Sending Capabilities
Sending Message via TCP Port
CommandSending(tcpMessage)
 CALL·/MEDIA/ETHERNET:tcpMessage(<IP_address>:<port_no>=<message>)
TextMessageSending(tcpText)
 CALL·/MEDIA/ETHERNET:tcpText(<IP_address>:<port_no>=<message>)
BinaryMessageSending(tcpBinary)
 CALL·/MEDIA/ETHERNET:tcpBinary(<IP_address>:<port_no>=<message>)
Sending Message via UDP Port
CommandSending(udpMessage)
 CALL·/MEDIA/ETHERNET:udpMessage(<IP_address>:<port_no>=<message>)
TextMessageSending(udpText)
 CALL·/MEDIA/ETHERNET:udpText(<IP_address>:<port_no>=<message>)
BinaryMessageSending(udpBinary)
 CALL·/MEDIA/ETHERNET:udpBinary(<IP_address>:<port_no>=<message>)
Sending Message via an RS-232 Port
CommandSending(sendMessage)
 CALL·/MEDIA/UART/<port>:sendMessage(<message>)
TextMessageSending(sendText)
 CALL·/MEDIA/UART/<port>:sendText(<message>)
BinaryMessageSending(sendBinaryMessage)
 CALL·/MEDIA/UART/<port>:sendBinaryMessage(<message>)
Sending CEC Commands
SendinganOSDString
SET·/MEDIA/CEC/<port>.OsdString=<text>

SendingaCECCommandinTextFormat
 CALL·/MEDIA/CEC/<port>:send(<command>)
SendingaCECCommandinHexadecimalFormat
 CALL·/MEDIA/CEC/<port>:sendHex(<hex_code>)
Appliedfirmwarepackage:v1.2.0 | LDCsoftware:v2.2.0
95