Changingthehdcpsetting(Inputport); Queryingthehdcpsetting(Outputport); Changingthehdcpsetting(Outputport); Testpatterngenerator - Lightware HDMI-TPS-TX210 User Manual

   
7.LW3Programmer'sReference
7.5.19. Changing the HDCP Setting (Input Port)
Command and Response #hdcp
SET·/MEDIA/VIDEO/<in>.HdcpEnable=<HDCP_setting>

pw·/MEDIA/VIDEO/<in>.HdcpEnable=<HDCP_setting>

Parameters
If the <HDCP_setting> parameter is 0 (or false)theHDCPisdisabledontheport,thus,encryptedcontentwill
not be present. If the value is 1 (or true)theHDCPisenabled,thus,encryptedcontentcanbereceived.
Example
 SET/MEDIA/VIDEO/I2.HdcpEnable=0
 pw/MEDIA/VIDEO/I2.HdcpEnable=false
7.5.20. Querying the HDCP Setting (Output Port)
HDCPcapabilityoftheoutputportcanbesettofollowtheinputportortoencryptthesignalalways.Latter
caseoccursifencryptedsignalisacceptedbythethird-partydeviceonly.SeemoreinformationintheHDCP
Management section.
Command and Response
 GET·/MEDIA/VIDEO/<out>.HdcpModeSetting
pw·/MEDIA/VIDEO/<out>.HdcpModeSetting=<HDCP_setting>

Parameters
If the <HDCP_setting> is 0 (or false) the port is in Automode,thus,theoutputportfollowsthesettingofthe
connected input port. If the <HDCP_setting>is1(ortrue),theoutgoingsignalisencryptedalways.
Example
 GET/MEDIA/VIDEO/O1.HdcpModeSetting
 pw/MEDIA/VIDEO/O1.HdcpModeSetting=0
7.5.21. Changing the HDCP Setting (Output Port)
Command and Response
SET·/MEDIA/VIDEO/<out>.HdcpModeSetting=<HDCP_setting>

pw·/MEDIA/VIDEO/<out>.HdcpModeSetting=<HDCP_setting>

Parameters
Seetheprevioussection.
Example
 SET/MEDIA/VIDEO/O1.HdcpModeSetting=0
 pw/MEDIA/VIDEO/O1.HdcpModeSetting=0
HDMI-TPS-TX200series–User'sManual
7.5.22. Test Pattern Generator
Theoutputportscansendaspecialimagetowardsthesinkdevicesfortestingpurposes.Thesettingis
availableonoutputportswiththebelow-listedparameters.
ATTENTION!

arecommonontheTPSandHDMIoutputports(O1andO2).
7.5.22.1. Test Pattern Generator Mode Setting
Command and Response
SET·/MEDIA/VIDEO/<out>.TpgMode=<mode_setting>

pw·/MEDIA/VIDEO/<out>.TpgMode=<mode_setting>

Parameters
Identifier
<mode_setting>
Example
 SET/MEDIA/VIDEO/O1.TpgMode=2
 pw/MEDIA/VIDEO/O1.TpgMode=2
7.5.22.2. Clock Source – The Clock Frequency of the Test Pattern
Command and Response
SET·/MEDIA/VIDEO/<out>.TpgClockSource=<clk_freq>

pw·/MEDIA/VIDEO/<out>.TpgClockSource=<clk_freq>

Parameters
Identifier
<clk_freq>
Example
 SET/MEDIA/VIDEO/O1.TpgClockSource=576
 pw/MEDIA/VIDEO/O1.TpgClockSource=576
Appliedfirmwarepackage:v1.2.0 | LDCsoftware:v2.2.0
TheModecanbesetindividuallyoneachport,buttheClocksourceandthePatternsettings
#testpattern #nosyncscreen
Parameterdescription
The current mode of the 0: disabled, the test pattern is not displayed on the output.
testpatterngenerator. 1: enabled, the test pattern is displayed on the output.
2: no signal mode, the test pattern is displayed if there is no
signalontheoutputport.
Parameterdescription
The clock frequency
480:480p.
of the of the pattern
576:576p.
generator.
EXT:externalclock(fromactualTMDSsource).
75
Parametervalues
Parametervalues