Allied Telesis x950 Series Installation Manual page 9

Figures
Figure 1: Front Panels of the x950 Switches ........................................................................................................................18
Figure 2: Rear Panel of the x950 Switches ..........................................................................................................................19
Figure 3: Link and Activity LEDs for Ports 1 to 24 ................................................................................................................23
Figure 4: Link and Activity LEDs for Ports 1 to 24 on the x950-28XTQm Switch .................................................................25
Figure 5: QSFP-4SFP10G-3CU and QSFP-4SFP10G-5CU Copper Breakout Cables........................................................26
Figure 6: ET3-MPO08-4LC-5 and ET3-MPO08-4LC-10 Fiber Optic Breakout Cables ........................................................27
Figure 7: LEDs for Ports 25 to 37 .........................................................................................................................................27
Figure 8: Management Panel ...............................................................................................................................................30
Figure 9: Switch ID LED with the eco-friendly Mode Disabled .............................................................................................32
Figure 10: Switch ID LED with the eco-friendly Mode Enabled ............................................................................................33
Figure 11: PWR600 Power Supply .......................................................................................................................................35
Figure 12: FAN05 Fan Module .............................................................................................................................................37
Figure 13: PORT Parameter in the Command Line Interface...............................................................................................38
Figure 14: Slot Numbers for Port Numbering on Stand-alone Switches...............................................................................39
Figure 15: XEM2 Ethernet Line Cards..................................................................................................................................42
Figure 16: XEM2-8XSTm Line Card .....................................................................................................................................45
Figure 17: XEM2-12XT Line Card ........................................................................................................................................49
Figure 18: XEM2-12XTm Line Card .....................................................................................................................................51
Figure 19: XEM2-12XS Line Card ........................................................................................................................................53
Figure 20: XEM2-4QS Line Card..........................................................................................................................................55
Figure 21: XEM2-1CQ Line Card..........................................................................................................................................57
Figure 22: Installation Options ..............................................................................................................................................65
Figure 23: Removing Accessories ........................................................................................................................................67
Figure 24: Removing the Shipping Box Partition ..................................................................................................................68
Figure 25: Lifting the Switch from the Shipping Box .............................................................................................................69
Figure 26: Removing the Switch from the Shipping End-caps and Protective Bag ..............................................................69
Figure 27: Accessory Kit.......................................................................................................................................................71
Figure 28: Removing the Power Cord and Documents from the PWR600 AC Power Supply .............................................73
Figure 29: Removing the Partition from the PWR600 AC Power Supply Shipping Box .......................................................74
Figure 30: Removing the Power Supply from the Shipping Box...........................................................................................75
Figure 31: Removing the Power Supply from the Shipping End-caps and Protective Bag ..................................................75
Figure 32: Removing the Blank Power Supply Panel from Slot PSU B................................................................................79
Figure 33: Sliding the PWR600 AC Power Supply into the Chassis.....................................................................................80
Figure 34: Seating the Power Supply on the Internal Connector..........................................................................................81
Figure 35: Removing the Blank Line Card Cover .................................................................................................................82
Figure 36: Removing the Ethernet Line Card from the Anti-static Bag.................................................................................83
Figure 37: Sliding the Ethernet Line Card into the Slot.........................................................................................................83
Figure 38: Seating the Ethernet Line Card in the Expansion Slot ........................................................................................84
Figure 39: Tightening the Two Captive Screws on the Ethernet Line Card..........................................................................85
Figure 40: Parts of the Bumper Feet ....................................................................................................................................87
Figure 41: Holes for Bumper Feet ........................................................................................................................................88
Figure 42: Inserting the Rivet Housing into the Bumper Foot...............................................................................................88
Figure 43: Placing the Bumper Foot on a Base Corner Hole ...............................................................................................89
Figure 44: Inserting the Rivet into the Bumper Foot .............................................................................................................89
Figure 45: Bracket Holes on the Switch................................................................................................................................92
Figure 46: Switch Orientations in an Equipment Rack .........................................................................................................93
Figure 47: Removing the Bumper Feet.................................................................................................................................94
Figure 48: Attaching the Equipment Rack Brackets .............................................................................................................96
Figure 49: Installing the Switch in an Equipment Rack.........................................................................................................96
9