Related Manuals for Allied Telesis SWITCH AND SWITCHBLADE X900
Summary of Contents for Allied Telesis SWITCH AND SWITCHBLADE X900
- Page 1 x900 Series Switch and SwitchBlade x908 ® Expansion Module Installation Guide XEM-1XP XEM-2XP XEM-12S XEM-12T XEM-2XT XEM-STK...
- Page 2 ® x900 Series Switch and SwitchBlade x908 Expansion Module Installation Guide XEM-1XP XEM-2XP XEM-12S XEM-12T XEM-2XT XEM-STK Download the complete document set from www.alliedtelesis.com/support/software...
- Page 3 Series Switch and SwitchBlade Document Number 613-000032 REV J © 2005-2010 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice.
-
Page 4: Table Of Contents
Installation Guide Contents About this Guide ... 4 Compatible Switches and Operating Systems ... 4 Compatible Pluggable Optical Modules ... 5 Package Contents ... 5 XEM-1XP 10 Gigabit XFP Port ... 6 XEM-2XP Dual 10 Gigabit XFP Ports ... 8 XEM-12S 100/1000BASE-X SFP Ports ... -
Page 5: About This Guide
Expansion Modules About this Guide Optional expansion modules (XEMs) enable economical combinations of port type, speed and density in a single switch. Front bays in the switch allow quick and easy installation. This Installation Guide describes how to install the following XEMs: ■... -
Page 6: Compatible Pluggable Optical Modules
SFP or XFP transceiver modules are approved for use. Package Contents The following items are included with each XEM: ■ this Installation Guide ■ one warranty card Contact your authorised Allied Telesis distributor or reseller if any items are damaged or missing. Installation Guide... -
Page 7: Xem-1Xp 10 Gigabit Xfp Port
Expansion Modules XEM-1XP 10 Gigabit XFP Port The XEM-1 XP single-port 10 Gigabit Ethernet expansion module features: ■ one XFP port ■ LEDs showing port status ■ support for hot-swappable XFP transceiver modules Front view XEM-1 XP The following LEDs report operations and faults on the XEM-1 XP. (Link Activity) LINK ENABLED... - Page 8 For the latest list of approved XFP transceiver modules, contact your authorised Allied Telesis distributor or reseller. See the most current revision available of the XEM datasheet (document number 617-000034) for further information about which XFP transceiver modules are approved for use with the XEM-1XP.
-
Page 9: Xem-2Xp Dual 10 Gigabit Xfp Ports
Expansion Modules XEM-2XP Dual 10 Gigabit XFP Ports The XEM-2 XP Dual 10 Gigabit Ethernet expansion module features: ■ two XFP ports ■ four LEDs (one set for each XFP port) showing port status ■ support for hot-swappable XFP transceiver modules Front view XEM-2 XP The following LEDs report operations and faults on the XEM-2XP. - Page 10 For the latest list of approved XFP transceiver modules, contact your authorised Allied Telesis distributor or reseller. See the most current revision available of the XEM datasheet (document number 617-000034) for further information about which XFP transceiver modules are approved for use with the XEM-2XP.
-
Page 11: Xem-12S 100/1000Base-X Sfp Ports
The following LEDs report operations and faults on the XEM-12 S. For the latest list of approved SFP transceiver modules, contact your authorised Allied Telesis distributor or reseller. See the most current revision available of the XEM datasheet (document number 617-000034) for further information about which SFP transceiver modules are approved for use with the XEM-12S. - Page 12 Caution It is recommended that you should wait 30 seconds between hot swapping any XEM to resume normal operations. Also ensure the XEM fastening thumbscrews are fully tightened. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller.
-
Page 13: Xem-12T 10/100/1000 Base-T Rj-45 Ports
Expansion Modules XEM-12T 10/100/1000 BASE-T RJ-45 Ports The XEM-12 T 12-port RJ-45 expansion module features: ■ two rows of 6 RJ-45 ports ■ gigabit ports that support speeds of 10/100/1000 Mbps ■ LEDs showing port status ■ cable fault detection and distance-to-fault diagnostics on switches running the AlliedWare®... - Page 14 Caution It is recommended that you should wait 30 seconds between hot swapping any XEM to resume normal operations. Also ensure the XEM fastening thumbscrews are fully tightened. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller.
-
Page 15: Xem-2Xt Dual 10G Base-T Rj-45 Ports
Caution It is recommended that you should wait 30 seconds between hot swapping any XEM to resume normal operations. Also ensure the XEM fastening thumbscrews are fully tightened. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller. 10G LINK State... -
Page 16: Xem-Stk Stacking Ports
XEM-STK Stacking Ports The XEM-STK dual-port stacking expansion module features: ■ two 15 Gbps full duplex stacking connections ■ LEDs showing port and stack member status ■ seven-segment stack ID display ■ recessed Select button to reset stack ID to 1 Front view XEM-STK PORT 1 MASTER... - Page 17 Expansion Modules A choice of 0.5 m or 2.0 m stacking cables can be ordered separately. For the latest list of approved cables, contact your authorised Allied Telesis distributor or reseller. The Select button resets the stack ID of this switch to 1, and causes the other members of the stack to be renumbered.
-
Page 18: Installation Procedure
■ Verify the package contents if you have not already done so. “Package Contents” on page contact your authorised Allied Telesis distributor or reseller. ■ Read the safety information for the switch. Safety information is available in the Installation and Safety Guide that is shipped with each switch. - Page 19 Expansion Modules ■ Gather necessary tools. You may need a Phillips #2 screwdriver to adjust the thumbscrews on the XEM. Installing or replacing XEMs without hot swap support Follow this procedure to: ■ install a XEM, except the XEM-STK, in a switch running the AlliedWare® operating system ■...
- Page 20 XEM to resume normal operations. Also ensure the XEM fastening thumbscrews are fully tightened. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller. Follow this procedure to hot swap a XEM in a switch running the AlliedWare Plus™...
- Page 21 Expansion Modules Verify the installation. If you have a terminal connected to the asyn0 port, any error message is displayed during installation. Confirm there is no error message about installation in the log file and that the switch has recognised the XEM, by using the commands: awplus>show system awplus>enable awplus#show log...
-
Page 22: Obtaining Documentation And Resources
You can download it from www.adobe.com. Other resources How-To Notes describe a range of standard Allied Telesis solutions, and include technical tips and guides to configuring specific hardware and software features. You can download the latest How-To Notes from www.alliedtelesis.com/resources/literature/howto.aspx. - Page 23 Contacting us With locations covering all of the established markets in North America, Latin America, Europe, Asia, and the Pacific, Allied Telesis provides localized sales and technical support worldwide. To find the representative nearest you, visit us on the Web at www.alliedtelesis.com.
Need help?
Do you have a question about the SWITCH AND SWITCHBLADE X900 and is the answer not in the manual?
Questions and answers