Table of Contents
Advertisement
!4
N o .
2
B U T T O N = 5 p s
C R O S S
The newly input data is stored under memory switch number "2". This completes the input procedure.
(The previous data remains stored under memory number "1".)
＊ The following switches are valid when inputting data.
The number specified is increased.
The number specified is reduced.
The previous indication display is restored.
The indication display is scrolled forward.
(Caution) 1. The number of buttons that can be specified in step 2 is from "2" through "20". If you
input any number except these, the corresponding error message will appear on the
display screen for three seconds. If this occurs, specify the correct number of buttons.
※ A single button can be sewn only when the machine is in the manual operation
mode or independent operation mode. (See page 35.)
2. When the total sum of each button interval specified in step 3 through 7 is not within
the range of 25.0 mm to 650.0 mm, the same error message as stated above will appear
on the screen. However, for the long-material mode, when the total sum of each button
interval is not within the range of 25.0 mm to 1,200.0 mm, the error message will
apppear.
3. If the button number specified in step 8 indicating the position to return the carriage
to its origin exceeds the number of buttons specified in step 2 or is set to "1", the
same error message will be shown on the display screen.
4. If the total sum of the feed amount up to the button number specified in step 8 indicating
the position to return the carriage to its origin exceeds 650 mm, the same error message
will appear on the display screen.
5. If a number except "1 through 20" is specified for the value for stacker timing in step
!0 ' , the same error message as stated above will be shown on the display screen.
6. If a number except "1 through 20" is specified in step !2 , the same error message as
stated above will be shown on the display screen.
Error indication on the display screen
＊ ＊ ＊ ＊ ＊ ＊
0 0
3) Checking the sewing data
The details of the sewing data stored under the designated memory number are shown on the display
screen.
(At this time, the data input is not possible.)
(Example) Machine operation to check the details of the data stored in memory in "2. Input of the sewing
data"
1
N o .
2
B U T T O N = 5 p s
C R O S S
Press
so that the sewing LED lights up. (
• Input data in the area bounded by a dotted line will be shown only for the "jump function" or "long-
material mode". (Refer to page 60 for how to set the mode.)
2
The distance for jump and the button number indicating the position to make the carriage return to its
origin are shown on the display screen.
3
B U T N
( p s )
I N D X
( m m )
The intervals from the first button to the 6th button are shown on the display screen.
S H I R T
C O U N T
D A T A
Error message
S H I R T
C O U N T
1 – – – – – 2 – – – – – 3 – – – – – 4 – – – – – 5 – – – – – ＊
1 0 0 . 0
1 0 0 . 0
I N D E X < 1 →
2 >
=
0
B O B B I N
The previous number is restored.
The inpu data is deleted.
E R R O R ＊ ＊ ＊ ＊ ＊ ＊ ＊
I N P U T
I N D E X < 1 →
2 >
=
0
B O B B I N
)
J U M P = 6 6 . 0 mm
R E T U R N
B U T T O N
1 0 0 . 0
1 0 0 . 0
31
−
−
= 1 0 0 .
0 m m
C O U N T
=
4 0 0
=
1 0 0 . 0 m m
C O U N T
=
4 0 0
N o . =
4
＊ ＊ ＊ .
＊
Advertisement
Table of Contents
