Danfoss VLT HVAC Basic Drive FC 100 Series Programming Manual page 119

Index
Motor
Control Principle............................................................................. 2-6
Current.................................................................................... 2-9, 2-55
Frequency......................................................................................... 2-9
Poles.................................................................................................. 2-10
Set-up...................................................................................... 1-2, 1-10
Speed Direction............................................................................ 2-17
Speed High Limit.......................................................................... 2-17
Speed Low Limit........................................................................... 2-17
Status................................................................................................ 2-54
Thermal Protection...................................................................... 2-12
Voltage.................................................................................... 2-8, 2-55
N
Navigation Keys And Indicator Lights (LEDs)............................ 1-1
Nominal Motor Speed....................................................................... 2-9
Not Changeable During Operation.............................................. 2-2
NPN........................................................................................................ 2-20
O
Open-loop............................................................................................. 2-6
Operating
Data................................................................................................... 2-52
Hours................................................................................................ 2-52
Mode................................................................................................... 2-1
State At Power-up.......................................................................... 2-1
Operation
Keys And Indicator Lights (LEDs).............................................. 1-1
Mode................................................................................................. 2-50
Output Filter....................................................................................... 2-50
Over
Temps............................................................................................... 2-52
Volts.................................................................................................. 2-52
Overmodulation................................................................................ 2-49
Over-voltage Control...................................................................... 2-13
P
Parameter Lists..................................................................................... 4-1
Parity And Stop Bits......................................................................... 2-37
Password................................................................................................ 2-5
PI
Anti Windup................................................................................... 2-59
Basic Settings................................................................................. 2-59
Controller........................................................................................ 2-59
Integral Time.................................................................................. 2-59
Normal/ Inverse Control............................................................ 2-59
Proportional Gain......................................................................... 2-59
PNP........................................................................................................ 2-20
Power
In Hp................................................................................................. 2-55
In KW................................................................................................. 2-54
Power-ups........................................................................................... 2-52
®
VLT HVAC Basic Drive Programming Guide
Preset
Programming
Protection Mode.................................................................................. 0-6
Protocol................................................................................................ 2-36
Q
Quick
R
Ramp
Rated Motor Speed............................................................................ 0-3
RCD........................................................................................................... 0-4
Readout And Programming Of Indexed Parameters.......... 1-12
Recommended Initialization........................................................ 1-12
Reference
Regional Settings................................................................................ 2-1
Relay
Relays.................................................................................................... 2-26
Reset
Reversing............................................................................................. 2-20
RFI Filter............................................................................................... 2-50
Run Permissive.................................................................................. 2-20
Running
S
Safety Precautions.............................................................................. 0-5
Semi-Auto Bypass Set-up.............................................................. 2-19
®
MG18B222 - VLT is a registered Danfoss trademark
Ref Bit 0............................................................................................ 2-20
Ref Bit 1............................................................................................ 2-20
Ref Bit 2............................................................................................ 2-20
Set-up................................................................................................. 2-2
With MCT-10 Setup Software..................................................... 1-1
Menu................................................................................................... 1-2
Stop Ramp Time........................................................................... 2-16
Transfer Of Parameter Settings Between Multiple Adjusta-
1 Ramp-down Time..................................................................... 2-15
1 Ramp-up Time........................................................................... 2-15
2 Ramp-down Time..................................................................... 2-16
2 Ramp-up Time........................................................................... 2-16
1 Source........................................................................................... 2-14
2 Source........................................................................................... 2-15
3 Source........................................................................................... 2-15
Output [bin]................................................................................... 2-56
Outputs............................................................................................ 2-24
Control Word Timeout............................................................... 2-36
KWh Counter................................................................................. 2-52
Mode................................................................................................. 2-49
SLC..................................................................................................... 2-42
Hours................................................................................................ 2-52
Hours Counter............................................................................... 2-52
ble Frequency Drives...... 1-12
6-3