Toshiba ACE-tronics G9 ASD Installation And Operation Manual page 296

Run Frequency Hysteresis, 127
Run Key, 33
Run Time, 54
Rush Relay Current Activation Time, 183
RX, 25, 26, 55
RX Input, 29
RX Input Bias, 165
RX Input Gain, 165
RX Input Point 1 Frequency, 116
RX Input Point 1 Rate, 118
RX Input Point 1 Setting, 116
RX Input Point 2 Frequency, 117
RX Input Point 2 Rate, 118
RX Input Point 2 Setting, 117
RX2, 55
RX2 (AI1) Input Bias, 166
RX2 (AI1) Input Gain, 166
RX2 (AI1) Input Point 1 Frequency, 120
RX2 (AI1) Input Point 1 Rate, 121
RX2 (AI1) Input Point 1 Setting, 119
RX2 (AI1) Input Point 2 Frequency, 120
RX2 (AI1) Input Point 2 Rate, 122
RX2 (AI1) Input Point 2 Setting, 120
S
S/L2, 16, 17
Save User Settings, 41
Second Speed Loop Proportional Gain, 163
Second Speed Loop Stabilization Coefficient, 164
Setpoints, 72
Short Circuit Detection At Start, 178
Short Circuit Protection, 276
Simple Positioning Completion Range, 154
Slack Rope, 58
Slack Rope Detection, 207
Slip Frequency Gain, 154
SOUT, 258
S-Pattern 1, 170
S-Pattern 2, 170
S-Pattern Acceleration Lower Limit Adjustment, 173
S-Pattern Acceleration Upper Limit Adjustment, 173
S-Pattern Deceleration Lower Limit Adjustment, 173
S-Pattern Deceleration Upper Limit Adjustment, 173
Special, 69
Special Functions, 46
Special Parameters, 70
Special Protection Parameters, 66
Speed at 0% Drooping Gain, 143
Speed at F320 Drooping Gain, 143
286
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Speed Control, 57
Speed Error, 258
Speed Limit (torque=0) Band, 160
Speed Limit (torque=0) Center Value, 159
Speed Limit (torque=0) Center Value Reference, 159
Speed Loop Proportional Gain, 163
Speed Loop Stabilization Coefficient, 163
Speed PID Switching Frequency, 164
Speed Reach Detection Band, 90
Speed Reach Frequency, 90
Speed Reference Setpoints, 67
ST (Standby), 92
Stall, 66
Stall Prevention Factor 1, 157
Stall Prevention Level, 176
Standard Mode Selection, 59
Start Frequency, 126
Startup Wizard Requirements, 42
Step Out, 258
Stepout Current Detection Level, 184
Stepout Current Detection Time, 184
Stopping Time at Stop Limit Switch UP, 135
Stop-Reset Key, 34
Super Creep Control, 57
Supply Voltage Correction, 141
SW2, 27
Switching Load Torque During Dynamic Braking, 147
Switching Load Torque During Power Running, 146
Synchronized Acceleration Time, 143
Synchronized Deceleration Time, 142
System Configuration and Menu Options, 52
System Grounding, 18
System Integration Precautions, 7
System Operation, 40
T
T/L3, 16, 17
T1, 17
T2, 17
T3, 17
Tension Torque Bias Input, 157
Terminal, 60
Terminal Descriptions, 26
Time Limit For Lower-Limit Frequency Operation, 128
Timed-Run, 58
Torque, 55, 72
Torque Command Selection, 157
Torque Control, 72
Torque Current, 55
ACE-tronics G9 ASD Installation and Operation Manual