Toshiba ACE-tronics G9 ASD Installation And Operation Manual page 97

F018
Preset Speed 1
Program  Frequency  Preset Speeds
Up to fifteen (15) output frequency values that fall within the Lower-Limit and
the Upper-Limit range may be programmed into the ASD and output as a
Preset Speed. This parameter assigns an output frequency to binary number
0001 and is identified as Preset Speed 1. The binary number is applied to
I1 – I4 of the ACE G9-120V-PCB to output the Preset Speed.
Perform the following setup to allow the system to receive Preset Speed
control input at the I1 – I4 terminals:
Program  Fundamental  Standard Mode Selection  Command Mode
1.
Selection  Terminal Board.
Program  Terminal  Input Terminals  I1 (set to Preset Speed 1; LSB
2.
of 4-bit count). Repeat for I2 – I4 (MSB of 4-bit count) as Preset Speed 2
– 4, respectively (all Normally Open).
Program  Frequency  Preset Speeds  Preset Speed 1 (set an output
3.
frequency as Preset Speed 1; repeat for Preset Speeds 2 – 15 as required).
Program  Pattern Run  Operation Mode  Preset Speed Operation
4.
Mode  Enabled/Disabled.
Select Enable to use the direction, accel/decel, and torque settings of the
Preset Speed being run. The torque settings used will be as defined in
– F181 and as selected via the associated discrete input terminals V/f
Switching 1 and 2 in Table 7 on pg.
Select Disabled to use the speed setting only of the Preset Speed being run.
5. Place the system in the Remote mode (Local/Remote LED Off).
6. Provide a Run command (activate F and/or R).
Activate I1 to run Preset Speed 1 (120 VAC to I1 = 0001 binary).
With I1 – I4 configured to output Preset Speeds
may be applied to I1 – I4 of the ACE G9-120V-PCB to run the associated
Preset Speed. If bidirectional operation is required F and R must be activated.
With I1 being the least significant bit of a binary count, the I1 – I4 settings will
produce the programmed speed settings as indicated in the Preset Speed Truth
Table to the right.
Preset Speeds are also used in the Pattern Run mode.
Preset Speed 2
Program  Frequency  Preset Speeds
This parameter assigns an output frequency to binary number 0010 and is
identified as Preset Speed 2. The binary number is applied to I1 – I4 of the
ACE G9-120V-PCB to output the Preset Speed (see
information on this parameter).
ACE-tronics G9 ASD Installation and Operation Manual
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
236.
(F115 – F118), 0001 – 1111
F018 for additional
Direct Access Number — F018
Parameter Type — Numerical
Factory Default — 60.0
Changeable During Run — Yes
Minimum — Lower Limit (F013)
Maximum — Upper Limit (F012)
Units — Hz
Preset Speed Truth Table
I4
Preset I3 I2
MSB
1 0 0
2 0 0
3 0 0
4 0 1
5 0 1
6 0 1
F170
7 0 1
8 1 0
9 1 0
10 1 0
11 1 0
12 1 1
13 1 1
14 1 1
15 1 1
Note: 1 = Terminal activated.
Direct Access Number — F019
Parameter Type — Numerical
Factory Default — 0.0
Changeable During Run — Yes
Minimum — Lower Limit (F013)
Maximum — Upper Limit (F012)
Units — Hz
F019
I1
Output
LSB
0 1 F018
1 0 F019
1 1 F020
0 0 F021
0 1 F022
1 0 F023
1 1 F024
0 0 F287
0 1 F288
1 0 F289
1 1 F290
0 0 F291
0 1 F292
1 0 F293
1 1 F294
87