Toshiba ACE-tronics G9 ASD Installation And Operation Manual page 288

Index
Numerics
0 Hz Command Output, 128
0 Hz Dead Band Signal, 127
16-Bit Binary/BCD Input, 91
24-Volt I/O Terminal Board, 23
A
Abnormal Speed Detection Time, 180
Abnormal Speed Settings, 65
Acc/Dec #1 – #4 Settings, 69
Acc/Dec Pattern 1, 170
Acc/Dec Pattern 1 – 4, 172
Acc/Dec Pattern 2, 171
Acc/Dec Special, 69
Accel/Decel #1 Settings, 59
Accel/Decel Operation After Torque Limit, 162
Accel/Decel Suspend, 147
Accel/Decel Switching Frequency 1, 172
Acceleration, 83
Acceleration Suspend Frequency, 147
Acceleration Suspend Time, 147
Acceleration Time 1, 83
Acceleration Time 2, 168
Acceleration Time 3, 173
Acceleration/Deceleration Switching Frequency 2, 174
Acceleration/Deceleration Switching Frequency 3, 175
Adding Input Selection, 186
Add-on Option 1 Error, 256
AI2, 91
AI2 (Option V/I) Input Bias, 166
Alarm Prohibition, 63
Alarms, 248, 249
Alternate I/O Terminal Board, 23
Always ON 1 Terminal 1, 92
AM, 25, 27
AM Bias Adjustment, 189
AM Output, 54
AM Output Gradient Characteristic, 189
AM Output Terminal Adjustment, 187
AM Output Terminal Function, 186
AM/FM Output, 29
Analog Filter, 66
Analog Function Assigned Object 11, 223
Analog Function Assigned Object 21, 223
Analog Input, 25
Analog Input Filter, 112
Analog Input Function Target 11, 222
Analog Input Function Target 21, 223
278
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Analog Input Loss, 254
Analog Input Over-Voltage, 254
Analog Output, 25
Analog Output Terminals, 60
Annual Average Ambient Temperature, 183
ASD Capacity, 13
ASD Characteristics, 13
ASD Disposition at ST Deactivation, 193
ASD Input Phase Failure Detection, 177
ASD Load, 54
ASD Number, 197
ASD OL (Overload) Trip, 54
ASD Operation at Disconnect, 205
ASD Output Phase Failure Detection, 177
ASD Overload, 54, 182, 254
ASD/Motor connection diagram, 17
ASD-side Switching Wait Time, 150
At-trip Recorded Parameters, 260
Auto Restart, 138
Automatic Acceleration/Deceleration, 79
Automatic Express-Speed Operation Frequency, 145
Automatic Function Selection, 89
Automatic Torque Boost, 79
Autotune Error, 254
Autotuning, 10
Autotuning 1, 154
Autotuning 2, 155
B
Base Frequency 1, 84
Base Frequency 2, 101
Base Frequency 3, 102
Base Frequency 4, 103
Base Frequency Voltage, 65
Base Frequency Voltage 1, 155
Base Frequency Voltage 2, 101
Base Frequency Voltage 3, 102
Base Frequency Voltage 4, 103
Bearing Greaser, 58
Bearing Greaser (Alarm) Time, 180
Bearing Greaser Speed Multiplier, 167
Bezel Mounting Hardware, 37
BIN Input Point 1 Frequency, 124
BIN Input Point 1 Setting, 123
BIN Input Point 2 Frequency, 124
BIN Input Point 2 Setting, 124
Block Read Data 1, 209
Block Read Data 2, 209
Block Read Data 3, 209
ACE-tronics G9 ASD Installation and Operation Manual