Table of Contents
Advertisement
5 - 36
5. OPERATION
SUB MENU
MAIN MENU
NEXT PAGE
-
INTERFACE
-
COMMAND MODE
-
COMMAND/PC
-
ISCP LOG
QUIT
(It is displayed only
when ISCP is selected
RESET LOG
with the COMMAND
MODE.)
COMM LOG
LOG RUN
EXIT
-
CAUTION
MAIN MENU
SUB MENU
NEXT PAGE
-
IRIS CIRCUIT ADJUST
QUIT
ADJUST MODE
FILTER SETUP
QUIT
POSITION ADJUST
ND FILE SETUP MODE
-
SINGLE FILTER MODE
-
BLK SET REF
QUIT
R BLK REF
G BLK REF
B BLK REF
ENGINEER SET FILE
QUIT
RENEW
DATA RENEW
MODE
PROGRAM UPDATE
CAMERA ROM
EXIT
-
****** ENGINEER PAGE2 ******
SELECT
DEFAULT
-
-
422, SINGLE
422
ICCP, ISCP
ICCP
(1200/2400/4800
/9600/19200)
COMMAND, PC
COMMAND
-
-
ON, OFF
-
0 to 82
0
START, STOP
START
-
-
W h e n I S C P i s s e l e c t e d w i t h t h e C O M M A N D M O D E , t h e u s u a l
remote controller cannot be connected. At this time, the menu
operation becomes impossible. In this case, please operate the
menu switch of CCU to return it to ISCP.
****** ENGINEER PAGE3 ******
SELECT
DEFAULT
-
-
-
-
-
-
-
-
ON, OFF
OFF
ON, OFF
OFF
ON, OFF
OFF
-
-
-100 to +100
-4
-100 to +100
-4
-100 to +100
-4
-
-
-
-
READY, CANCEL,
-
EXECUTE
-
-
FUNCTION
Moves to ENGINEER PAGE3.
Switches I/O interfaces of the REMOTE connector.
422 : balanced RS-422 level, SINGLE : unbalanced TTL level
Switches communication protocols of the REMOTE connector.
ICCP : Standard remote controller protocol in two-way handshaking
mode.
ISCP : Remote control protocol in one-way or two-way handshaking
mode. Baud rate is set according to the communication speed.
COMMAND : Mode for connecting standard remote controller.
PC : Mode for adjusting. It is not used usually.
Moves from the sub menu to the main menu.
OFF : Saves the received data log.
ON : When it is set to ON, data is reset to 0 by selecting EXE.
Received data log of ISCP command is displayed by selecting "COMM
LOG." And the data up to 100 can be confirmed by changing the numerical value.
START : Saves the received data to the log.
STOP : Does not save the received data to the log.
Turns off the menu.
FUNCTION
Moves to ENGINEER PAGE4.
Moves from the sub menu to the main menu.
Adjusts the relationship between the fixed iris value and the answer value.
Moves from the sub menu to the main menu.
When it is set to ON, impresses the voltage to filter servo forcibly.
Creates ND FILE when set to ON, and AWB is executed at each ND
filter position.
When it is set to ON, operates as same as the filter structure of 1 :
through, 2 : 5600k, 3 : 5600k+1/4ND, 4 : 5600k+1/64ND at the CC filter
command.
Moves from the sub menu to the main menu.
R ch correction value
G ch correction value
B ch correction value
Moves from the sub menu to the main menu.
Saves the camera level adjustments and menu item settings. The saved
data can be read as user-set data through "PRESET FILE LOAD" of
MENU PAGE6.
Updates the program software of the camera.
Operates while connecting the remote controller (RCP-50B, etc.) with a
memory card slot.
Turns off the menu.
Advertisement
Table of Contents
