Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY RX1330 M3 Upgrade and Maintenance Manual April 2017...
Page 2: Copyright And Trademarks
– The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
Page 5 Only for Japan: Shielded LAN cables should be used in this product. Only for Japan: Although described in this manual, some sections do not apply for Japan. These options and routines include: – CSS (Customer Self Service) – USB Flash Module (UFM) Upgrade and Maintenance Manual RX1330 M3...
Page 6: Version History
Version history Issue number Reason for update 1.0 / April 2017 Initial release Upgrade and Maintenance Manual RX1330 M3...
Page 7: Table Of Contents
Contents Introduction ......21 Notational conventions ....22 Before you start .
Page 8 Contents Shutting down the server ....53 Disconnecting the power cord ....54 Getting access to the component .
Page 9 Contents 5.2.7 Resetting the error status after replacing memory modules or CPUs ......86 5.2.7.1 Memory modules .
Page 10 Concluding steps ..... . 120 Fujitsu battery unit (FJBU) ....121 6.4.1...
Page 11 Contents Hard disk drive (HDD) / solid state drive (SSD) ..133 Basic information ..... . . 134 7.1.1 Handling HDDs or SSDs without installation frame .
Page 12 Contents 7.2.10 Replacing the SAS expander board ....163 7.2.10.1 Preliminary steps ..... . 163 7.2.10.2 Removing the defective SAS expander board .
Page 13 Contents Fans ....... 179 Basic information ..... . . 180 8.1.1 Numbering of the fan modules .
Page 14 Contents 9.4.4 Replacing a riser card ..... . 204 9.4.4.1 Preliminary steps ..... . 204 9.4.4.2 Removing the riser card .
Page 15 Contents 10.2.3 Installing a memory module ....226 10.2.4 Concluding steps ......227 10.3 Removing a memory module .
Page 16 Contents 12.2.2 Removing the ODD ..... . . 252 12.2.2.1 Preliminary steps ..... . 252 12.2.2.2 Removing the ODD .
Page 17 Contents 13.4 Front panel on QRL (10 x 2.5-inch HDD configuration) . . . 268 13.4.1 Replacing the front panel on QRL ....268 13.4.1.1 Preliminary steps .
Page 18 Contents 14.4.3 Replacing the TPM ..... . . 292 14.4.3.1 Preliminary steps ..... . 293 14.4.3.2 Removing the defective TPM .
Page 19 Indicator on hot-plug PSUs (slide-in unit) ..338 16.2.3.4 Indicator on Fujitsu battery unit (FJBU) ... 339 16.3 Onboard settings ......340 16.4...
Page 20 Contents Upgrade and Maintenance Manual RX1330 M3...
Page 21: Introduction
Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.
Page 22: Notational Conventions
Introduction Notational conventions The following notational conventions are used in this manual: indicates commands or menu items Text in italics indicates system output fixed font indicates text to be entered by the user semi-bold fixed font "Quotation marks" indicate names of chapters and terms that are being emphasized describes activities that must be performed in the order Ê...
Page 23: Before You Start
Before you start Before you start any upgrade or maintenance task, please proceed as follows: Ê Carefully read the safety instructions in chapter "Important information" on page Ê Make sure that all necessary manuals are available. Refer to the documentation overview in section "Documents you need at hand"...
Page 24 For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information.
Page 25: Classification Of Procedures
At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more detailed information. 2.1.1 Customer Replaceable Units (CRU)
Page 26: Upgrade And Repair Units (Uru)
(Repair Units). For Japan, customer allows only upgrade. For upgrade units as customer replaceable, please refer to: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Server management error messages and diagnostic indicators on the front panel and system board will report defective Upgrade and Repair Units as customer replaceable CSS components.
Page 27: Field Replaceable Units (Fru)
Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...
Page 28: Average Task Duration
Before you start Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. Refer to the following table for an overview of steps taken into account for calculating the average task duration: Step included...
Page 29: Tools You Need At Hand
Before you start Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below. You will find a list of required tools at the beginning of each procedure. List of used screws (not valid for Japan) Screw driver/ bit insert Screw...
Page 30 Before you start Screw driver/ bit insert Screw Usage Type Torque M2 x 4 mm Torx Plus 6 (black) ODD latch 0.09 Nm C26192-Y10-C166 Phillips M3 x 4 mm UFM nylon PH1 / (+) No. 1 (white) screw 0.06 Nm A3C40109082 Phillips M2.5 x 4 mm...
Page 31 Before you start List of used screws for Japan Screw driver/ bit insert Screw Usage Type Torque Phillips M3 x 6 mm Slot bracket to PH2 / (+) No. 2 (silver) chassis, system board 0.6 Nm F6-SW2N3-06121 Phillips M3 x 5 mm Slot bracket to PH2 / (+) No.
Page 32: Documents You Need At Hand
– Ensure to store all printed manuals enclosed with your server in a save place for future reference. – Unless stated otherwise, all manuals are available online at under x86 Servers. http://manuals.ts.fujitsu.com For Japan please use the following address: http://www.fujitsu.com/jp/products/computing/servers/primergy/manual/ Upgrade and Maintenance Manual...
Page 33 Before you start Document Description "Quick Start Hardware - Quick installation poster for initial operation, FUJITSU Server PRIMERGY available online RX1330 M3" leaflet "ServerView Quick Start Guide" Information on initial server setup and " ServerView クイックスタート software configuration, available online ガイド...
Page 34 Recycling and contact information, "Service Desk" leaflet available online, or as a printed copy " サポート＆サービス " for Japan RAID documentation, available online at http://manuals.ts.fujitsu.com under x86 Servers - Expansion Cards - Storage Adapters Additional documentation For Japan please use the following address: http://www.fujitsu.com/jp/products/computing/s...
Page 35: Important Information
Important information Depending on your server or the installed options some information is not valid for your server. CAUTION! Before installing and starting up a server, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the server and endanger the data base.
Page 36 Important information Before starting up During installation and before operating the server, observe the instructions ● on environmental conditions for your server. If the server is brought in from a cold environment, condensation may form ● both inside and on the outside of the server. Wait until the server has acclimatized to room temperature and is absolutely dry before starting it up.
Page 37 Important information Always connect the server and the attached peripheral devices to the same ● power circuit. Otherwise you run the risk of losing data if, for example, the server is still running but a peripheral device (e.g. memory subsystem) fails during a power outage.
Page 38 Important information The warranty is void if the server is damaged during installation or ● replacement of server expansions. Only set screen resolutions and refresh rates that are specified in the ● operating manual for the monitor. Otherwise, you may damage your monitor. If you are in any doubt, contact your sales outlet or customer service center.
Page 39 Important information The battery used in this server may present a fire or chemical burn hazard if ● mistreated. Do not disassemble, heat about 100 °C (212F), or incinerate the battery. Replace the lithium battery on the system board in accordance with the ●...
Page 40 Important information Do not pull on, press hard, or otherwise handle the CD/DVD/BD tray ● roughly. Do not disassemble the optical disk drive. ● Before use, clean the optical disk tray using a soft, dry cloth. ● As a precaution, remove disks from the optical disk drive when the ●...
Page 41 Important information You can prevent damage from the optical disk drive and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: – Only insert disks in the drive when needed and remove them after use.
Page 42 Important information The circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. To ensure reliable protection, you must wear an earthing band on your wrist when working with ESD modules and connect it to an unpainted, conducting metal part of the server.
Page 43 Important information When connecting and disconnecting cables, observe the relevant ● instructions in the "Important Information" chapter of the technical manual for the corresponding rack. The technical manual is supplied with the corresponding rack. When installing the rack, make sure that the anti-tilt mechanism is ●...
Page 44: Energy Star
CPU utilization levels. CE conformity :The system complies with the requirements of European Regulations. Find the CE declaration on certificate portal: https://sp.ts.fujitsu.com/sites/certificates/default.aspx To open the CE declaration applicable for your system, proceed as follows: Ê Select Industry Standard Servers.
Page 45: Fcc Class A Compliance Statement
Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Page 46: Environmental Protection
Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
Page 47 Further information can be found at: http://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: http://ts.fujitsu.com/recycling Upgrade and Maintenance Manual RX1330 M3...
Page 48 Important information Upgrade and Maintenance Manual RX1330 M3...
Page 49: Basic Hardware Procedures
Basic hardware procedures Using diagnostics information Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. Please refer to the following ServerView Suite topics: – Operation – Maintenance It is recommended to prepare local maintenance tasks using remote diagnostics procedures, as described in the "ServerView Suite Local Service Concept...
Page 50: Locating The Defective Server
Basic hardware procedures 4.1.1 Locating the defective server When working in a datacenter environment, switch on the ID indicator on the front and rear connector panels of the server for easy identification. Ê Press the ID button on the front panel, use the iRMC web frontend or the ServerView Operation Manager user interface to switch on the system identification LEDs.
Page 51: Customer Self Service (Css) Indicator
Basic hardware procedures – Software / agent related errors: Check the ServerView System Monitor, available on Windows or Linux based servers with ServerView agents installed. For further information, please refer to the "ServerView System Monitor" user guide. 4.1.2.2 Customer Self Service (CSS) indicator Ê...
Page 52: Local Diagnostic Indicators On The System Board
Basic hardware procedures 4.1.3.2 Local diagnostic indicators on the system board Using the Indicate CSS button Ê Shut down and power off the server. Ê Disconnect the AC power cord(s) from the system. It is mandatory to disconnect power cords in order to use the Indicate CSS functionality.
Page 53: Shutting Down The Server
Basic hardware procedures Shutting down the server CAUTION! For further safety information, please refer to chapter "Important information" on page This step is only required when upgrading or replacing non-hot plug components. Ê Inform the system administrator that the server will be shut down and put offline.
Page 54: Disconnecting The Power Cord
Basic hardware procedures Disconnecting the power cord Standard power supply Figure 2: Unlocking the cable tie of a standard PSU Ê Pull out on the locking lever on the cable tie (1) and loosen the loop (2). Ê Disconnect the power cord from the PSU and remove it from the cable tie. Redundant power supply Figure 3: Unlocking the cable clamp of a PSU Ê...
Page 55: Getting Access To The Component
Basic hardware procedures Getting access to the component CAUTION! Only for non-hot plug components: ● Before removing or attaching covers, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the outlet. Failure to do so can cause electric shock. The top cover must be replaced as soon as possible for purposes of ●...
Page 56: Extending The Server Out Of The Rack
Basic hardware procedures 4.4.1 Extending the server out of the rack CAUTION! Use the anti-tilt plate to prevent the rack from tipping when installing ● the rack. Pulling the server out of the rack without having installed the anti-tilt plate may cause the rack to tip over. Be careful not to pinch fingers or clothes when sliding out the server ●...
Page 57: Removing The Server From The Rack
Basic hardware procedures 4.4.2 Removing the server from the rack In most cases maintenance tasks can be performed while the server is extended from the rack. However, depending on accessibility or security guidelines, it may make sense to completely remove the server from the rack cabinet for maintenance purposes.
Page 58 Basic hardware procedures Figure 5: Removing the server from the rack Ê Release the locking bars on both rack rails (1). Ê Lift the server out of the rack rails (2) and place it on an even surface. Upgrade and Maintenance Manual RX1330 M3...
Page 59: Removing The Top Cover
Basic hardware procedures 4.4.3 Removing the top cover Figure 6: Removing the top cover Ê Push green touch points inside (1). Ê Push the top cover as far as it will go in the direction of the arrow (2). Ê Lift off the top cover upward (3). Upgrade and Maintenance Manual RX1330 M3...
Page 60: Reassembling
Basic hardware procedures Reassembling CAUTION! Before attaching the covers, make sure no unnecessary parts or tools ● are left inside the server. The top cover must be replaced as soon as possible for purposes of ● cooling, to comply with EMC regulations (regulations regarding electromagnetic compatibility) and to prevent fires.
Page 61: Installing The Server In The Rack
Basic hardware procedures 4.5.2 Installing the server in the rack CAUTION! At least two people are needed to position the server on the rack rails. (For Japan, please refer to " 安全上のご注意 ".) For configurations below 32 kg: At least two people are needed to lift the server into the rack cabinet.
Page 62 Basic hardware procedures Figure 8: Inserting the server into the rack rails Ê Fully extend the rack rails until they lock in place (1). The rack rails must click into place so that they can no longer be moved. Ê At a slight angle, lower the server onto the rear mounting point on the rack rails (2).
Page 63: Sliding The Server Into The Rack
Basic hardware procedures 4.5.3 Sliding the server into the rack Figure 9: Sliding the server into the rack Ê Release the locking mechanism of both rails (1). Ê Push the server as far as it will go into the rack (2) until the quick-release levers engage (3).
Page 64: Connecting The Power Cord
Basic hardware procedures Connecting the power cord CAUTION! The server supports a mains voltage in the range of 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage. Standard power supply Ê...
Page 65 Basic hardware procedures Redundant power supply Ê If applicable, connect the mains plugs to power outlets of the rack socket strip. To provide true phase redundancy, the second PSU should be connected to a different AC power source from the other PSU. If one AC power source should fail, the server will still continue to run.
Page 66: Switching On The Server
Basic hardware procedures Switching on the server CAUTION! Before switching on the server, make sure the top cover is closed. In ● order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the top cover is removed. For further safety information, please refer to chapter "Important ●...
Page 67 Basic hardware procedures Figure 13: Removing the riser module 2 Figure 14: Removing the riser module 3 Figure 15: Removing the full height riser module Ê If necessary, disconnect cables from the other components. Ê Carefully pull out the riser module upward. Upgrade and Maintenance Manual RX1330 M3...
Page 68: Installing A Riser Module
Basic hardware procedures 4.8.2 Installing a riser module Figure 16: Installing the riser module 1 Figure 17: Installing the riser module 2 Figure 18: Installing the riser module 3 Upgrade and Maintenance Manual RX1330 M3...
Page 69 Basic hardware procedures Figure 19: Installing the full height riser module Ê Insert the riser card into the system board slot and press down the green touch points (see circles). CAUTION! Valid for the full height riser module: Make sure that the EMC springs make contact correctly (see close- ups).
Page 70 Basic hardware procedures Upgrade and Maintenance Manual RX1330 M3...
Page 71: Basic Software Procedures
Basic software procedures Starting the maintenance task 5.1.1 Suspending BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. In the scenario described here, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.
Page 72: Disabling Svom Boot Watchdog Functionality
For further information on how to suspend BitLocker drive encryption, please refer to the Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. Please refer to the Fujitsu web pages for more details. 5.1.2 Disabling SVOM boot watchdog functionality The ServerView Operations Manager boot watchdog determines whether the server boots within a preset time frame.
Page 73: Configuring Boot Watchdog Settings
Basic software procedures Ê Under Boot Watchdog, you can obtain detailed information about the current watchdog status, time out intervals and actions that are triggered if watchdog time outs are exceeded. For detailed information on BIOS settings, refer to the corresponding BIOS Setup Utility reference manual.
Page 74: Removing Backup And Optical Disk Media
For further information on "forcible" tape ejection, please refer to the "Tape Facts" pages available to Fujitsu service partners from the following https address: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/Pages/ TapeFacts.aspx...
Page 75: Verifying And Configuring The Backup Software Solution
This is a known restriction of Windows PE with Multipath drivers. Using Update Manager Express Ê If performing an offline BIOS / firmware update, first of all prepare the ServerView Update DVD or USB stick: Ê Download the latest ServerView Update DVD image from Fujitsu: ftp://ftp.ts.fujitsu.com/images/serverview http://www.fujitsu.com/jp/products/computing/servers/primergy/support/ (for Japan) svsdvd/dvd/ Ê...
Page 76 Basic software procedures Ê Before using the ServerView Update DVD or USB stick in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN, FC or SAS cables) from the system. Only keep mouse, keyboard, video cable and AC power cord connected. Ensure that all external I/O connections are uniquely identified so that you can reconnect them into their original locations after concluding the task.
Page 77 Basic software procedures Using PrimeCollect To start PrimeCollect, proceed as follows: Ê Before using PrimeCollect in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN, FC or SAS cables) from the system. Only keep mouse, keyboard, video cable and AC power cord connected.
Page 78: Switching On The Id Indicator
Basic software procedures 5.1.6 Switching on the ID indicator When working in a datacenter environment or a server room, switch on the ID indicator on the front and rear connector panels of the server for easy identification. For further information, refer to section "Locating the defective server"...
Page 79: Completing The Maintenance Task
Fujitsu support internet pages at: http://ts.fujitsu.com/support/ For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/ Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. 5.2.1.1 Updating or recovering the system board BIOS BIOS flash procedure Ê...
Page 80 Basic software procedures Ê Choose one of the following options from the update tool menu to start the iRMC update process: Normal Choose this option to update an existing system board. Initial Choose this option if the system board has been replaced prior to the iRMC update procedure.
Page 81: Verifying System Information Backup / Restore
Basic software procedures CAUTION! Do not interrupt the iRMC upgrade process after it has started. If the process is interrupted, the iRMC BIOS may be permanently corrupted. If the iRMC does not work after flashing, disconnect the system from the mains and reconnect it again. Ê...
Page 82: Updating Expansion Card Firmware
"Local System Update for PRIMERGY Servers" user guide Using the flash tool The latest firmware files are available as ASPs (Autonomous Support Packages) for Windows or as DOS tools from the Fujitsu support web pages at: http://ts.fujitsu.com/support/ For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/ Ê...
Page 83: Enabling Option Rom Scan
Basic software procedures or enter its serial or ident number into the search field. Ê Select your operating system and version. Ê Select the desired component type (e.g. SAS RAID). Ê Select your controller from the device list to expand a compilation of available drivers and firmware.
Page 84: Reconfiguring The Backup Software Solution
Further information on suitable backup software solutions and related documentation is available from the Fujitsu web pages. Re-enabling backup drives If a backup drive has been disabled or deleted from the backup software drive list as described in section "Verifying and configuring the backup software...
Page 85: Resetting The Boot Retry Counter
Basic software procedures Ê Under Boot Retry Counter the current number of remaining boot attempts is displayed. The value is further decremented with every failed boot attempt or system reboot resulting from critical system errors. Ê Exit the BIOS. 5.2.6.2 Resetting the boot retry counter The boot retry counter should be reset to its original value concluding every service task.
Page 86: Resetting The Error Status After Replacing Memory Modules Or Cpus
Basic software procedures Resetting the boot retry counter using iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Server Management menu. Ê The following boot retry counter settings are available under ASR&R Options: Ê Under Retry counter max specify the maximum number of attempts to boot the operating system (0 to 7).
Page 87 Using ServerView Maintenance Tools (Windows only) Ê Launch the ServerView Maintenance Tools: – Windows Server 2008 R2 and below: Start > (All) Programs > Fujitsu > ServerView Suite > Agents > Maintenance Tools – Windows Server 2012 and above: Start > Apps > Fujitsu > Maintenance Tools Ê...
Page 88: Cpus
Using ServerView Maintenance Tools (Windows only) Ê Launch the ServerView Maintenance Tools: – Windows Server 2008 R2 and below: Start > (All) Programs > Fujitsu > ServerView Suite > Agents > Maintenance Tools – Windows Server 2012 and above: Start > Apps > Fujitsu > Maintenance Tools Ê...
Page 89: Enabling Svom Boot Watchdog Functionality
Basic software procedures Ê If the error status cannot be reset with the method above, please use the following procedure for resetting the error counter of all CPUs: Ê Log in as root. Ê Enter the commands below, followed by [ENTER]: 1.
Page 90: Enabling Replaced Components In The System Bios
Basic software procedures Configuring boot watchdog settings using the iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Server Management menu. Ê Under Watchdog Settings ensure that the check box next to Boot Watchdog is selected. From the drop down list choose Reset and specify the desired timeout delay.
Page 91: Verifying The Memory Mode
Basic software procedures 5.2.10 Verifying the memory mode If a memory module fails, the server will reboot and the defective module will be disabled. As a result, the current operation mode (e.g. Mirrored Channel mode) may no longer be available due to a lack of identical memory module pairs. In this case, the operation mode will automatically revert to Independent Channel Mode.
Page 92: Viewing And Clearing The System Event Log (Sel)
Basic software procedures Ê Select the Main menu. Ê Under System Time and System Date specify the correct time and date. By default, the system time set in the BIOS is RTC (Real Time Clock) local time. If your IT infrastructure relies on universally accepted time standards, set the System Time to UTC (Universal Time, Coordinated) instead.
Page 93: Clearing The Sel
Basic software procedures may have to log on to the server beforehand. The status of the component will then be reset to ok. To see the new status you must refresh the Driver Monitor view with Refresh. For detailed information on how to view and sort the SEL using ServerView Operations Manager, refer to the "ServerView Operations Manager - Server Management"...
Page 94: Updating The Nic Configuration File In A Linux And Vmware Environment
Basic software procedures 5.2.13 Updating the NIC configuration file in a Linux and VMware environment In order to prevent errors caused by changing network device names (eth<x>), it is recommended to store the MAC address (hardware address) of a network interface card in the related NIC configuration file of the Linux OS.
Page 95: Resuming Bitlocker Functionality
Basic software procedures Ê For the changes to take effect, you need to reboot the network by entering the following command: # service network restart If the system board or network controller offers multiple LAN ports, it is necessary to update the remaining ifcfg-eth<x> definition files accordingly.
Page 96: Performing A Raid Array Rebuild
Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. Please refer to the Fujitsu web pages for more details. 5.2.15 Performing a RAID array rebuild After replacing an HDD that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process.
Page 97: Looking Up Changed Mac / Wwn Addresses
Basic software procedures 5.2.16 Looking up changed MAC / WWN addresses When replacing a network controller, the MAC (Media Access Control) and WWN (World Wide Name) addresses will change. In addition to the procedures described below, MAC / WWN addresses can also be found on the type label attached to a network controller or system board.
Page 98: Using The Chassis Id Prom Tool
After replacing the Chassis ID EPROM, system information has to be entered using the Chassis ID Prom tool. The tool and further instructions are available to maintenance personnel from the Fujitsu Technology Solutions Extranet: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ Ê Select your PRIMERGY system from the main area of the page.
Page 99: Configuring Lan Teaming
Basic software procedures Note on Advanced Thermal Design (ATD) If the Advanced Thermal Design (ATD) option is available and has been enabled for your server, please set information within the Chassis ID Prom Tool accordingly. The ATD option can only be ordered from the manufacturer as a factory preset.
Page 100: After Replacing The System Board
Basic software procedures 5.2.18.2 After replacing the system board Ê Confirm with the customer whether the onboard LAN controller you have replaced has been used as part of a LAN teaming configuration. Ê If LAN teaming has been active, you will need to restore the configuration using the LAN driver utility after replacing the system board.
Page 101: Performing A Fan Test
Basic software procedures 5.2.20 Performing a fan test Notes on replacing a defective fan After replacing a defective system fan or PSU containing a defective fan, the fan error indicators will stay lit until the next fan test. By default, a fan test is automatically started every 24 hours.
Page 102 Basic software procedures Ê After the fan test is complete, restore the time setting to its initial value and click Save Page. For more detailed information, refer to the "ServerView Operations Manager" user guide. For Japan: Executing the fan test via Chassis ID Prom Tool Please follow the instructions provided separately.
Page 103: Power Supply Unit (Psu)
Power supply unit (PSU) Safety notes CAUTION! Do not disassemble the PSU. Doing so may cause electric shock. ● Areas around the PSU may remain extremely hot after shutdown. ● After shutting down the server, wait for hot components to cool down before removing the PSU.
Page 104: Basic Information
PSU can be replaced during operation (hot-plug). – or one hot-plug PSU and a Fujitsu battery unit (FJBU) Besides the PSU, an FJBU can be installed optionally as a modular UPS. When power fail happened, the server can operate via FJBU for a while. The FJBU can be replaced during operation (hot-plug).
Page 105: Standard Power Supply
Power supply unit (PSU) Standard power supply 6.2.1 Replacing the standard PSU Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 6.2.1.1 Preliminary steps "Locating the defective server" on page 50 Ê "Suspending BitLocker functionality" on page 71 Ê...
Page 106 Power supply unit (PSU) Figure 22: Removing the screws Ê Remove the two screws (see circles). Figure 23: Taking out the standard PSU Ê Remove the two screws (1). Ê Pull the PSU a few centimeters toward the inside (2). Ê...
Page 107: Installing The New Standard Psu
Power supply unit (PSU) 6.2.1.3 Installing the new standard PSU Figure 24: Inserting the standard PSU Ê Insert the PSU into the bay (1). Ê Push the PSU toward the adapter plate (2). Ê Fasten the PSU with two screws in the chassis (3). Ê...
Page 108: Concluding Steps
Power supply unit (PSU) Figure 25: Connecting the power cables Ê Connect the two power cables to the system board connectors "PC98" and "PWR1". For the cable plan see section "Cabling plans" on page 312. 6.2.1.4 Concluding steps "Reassembling" on page 60 Ê...
Page 109: Redundant Power Supply
Power supply unit (PSU) Redundant power supply PSU 1 PSU 2 Figure 26: PSU bays 6.3.1 Installing a hot-plug PSU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.3.1.1 Preliminary steps No steps needed. 6.3.1.2 Removing the dummy cover Figure 27: Removing a dummy cover Ê...
Page 110: Installing A Hot-Plug Psu
Power supply unit (PSU) 6.3.1.3 Installing a hot-plug PSU Figure 28: Folding up the handle Ê Push the handle of the PSU halfway upward in the direction of the arrow. Figure 29: Installing the hot-plug PSU Ê Push the PSU into its bay (1) as far as it will go until the locking latch snaps in place.
Page 111: Concluding Steps
Power supply unit (PSU) Figure 30: Installing the cable tie Ê Push the cable tie into the corresponding hole until it clicks in. 6.3.1.4 Concluding steps "Connecting the power cord" on page 64 Ê Upgrade and Maintenance Manual RX1330 M3...
Page 112: Removing A Hot-Plug Psu
Power supply unit (PSU) 6.3.2 Removing a hot-plug PSU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less Note for servers using CMA (Cable Management Arm) Regarding of removing PSUs, additional tasks are needed, due to an interference between CMA stopper and the PSUs. Figure 31: Unlocking the CMA stopper Ê...
Page 113 Power supply unit (PSU) Figure 32: Removing the CMA stopper Ê Remove the CMA stopper with the mounted crossbar. Ê Hold the CMA stopper, the crossbar and the CMA including cables in the one hand. Figure 33: Removing the PSU Ê...
Page 114: Preliminary Steps
Power supply unit (PSU) 6.3.2.1 Preliminary steps No steps needed. 6.3.2.2 Removing a hot-plug PSU Ê Remove the power cord from the dedicated PSU as described in section "Disconnecting the power cord" on page 54 Figure 34: Unlocking and removing the hot-plug PSU Ê...
Page 115: Installing The Dummy Cover
Power supply unit (PSU) 6.3.2.3 Installing the dummy cover Figure 35: Installing the dummy cover Ê Insert the dummy cover into the empty bay with the impressed arrow symbol facing to the top (see circle). Ensure that the upper rear cant of the dummy cover fits under the PSU cage. Ê...
Page 116: Preliminary Steps
Power supply unit (PSU) Note for servers using CMA (Cable Management Arm) Regarding of replacing PSUs, additional tasks are needed, due to an interference between CMA stopper and the PSUs. Ê Push the lock spring inward to unlock the CMA stopper (see figure 31). CAUTION! In case of not enough space at the under side, unlock the CMA stopper of the server below and pull out the CMA to the rear side...
Page 117: Installing The New Hot-Plug Psu
Power supply unit (PSU) 6.3.3.3 Installing the new hot-plug PSU Ê Install the PSU as described in section "Installing a hot-plug PSU" on page 110. 6.3.3.4 Concluding steps Ê Connect the power cord to the new PSU and secure it with a cable tie as described in section "Connecting the power cord"...
Page 118: Removing The Defective Power Distribution Board
Power supply unit (PSU) 6.3.4.2 Removing the defective power distribution board Ê Remove all PSUs as described in section "Removing a hot-plug PSU" on page 114. Figure 36: Removing the power distribution board Ê Disconnect the two power cables from the power distribution board (see orange arrows).
Page 119: Installing The New Power Distribution Board
Power supply unit (PSU) 6.3.4.3 Installing the new power distribution board Figure 37: Installing the power distribution board Ê Insert the power distribution board (1) and slide it in the guidings of the chassis (2). Ê Fasten the power distribution board with one screw (see circle). Ê...
Page 120: Concluding Steps
Power supply unit (PSU) Ê Install the PSUs as described in section "Installing a hot-plug PSU" on page 110. 6.3.4.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê...
Page 121: Fujitsu Battery Unit (Fjbu)
Power supply unit (PSU) Fujitsu battery unit (FJBU) 6.4.1 Installing the FJBU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.4.1.1 Preliminary steps No steps needed. 6.4.1.2 Removing the dummy cover Figure 39: Removing a dummy cover Ê Press in on both release latches (1) and remove the dummy cover (2).
Page 122: Installing An Fjbu
Ê No steps needed. To execute auto shutdown after power fail, you should install the FJBU management software. How to install and configure the FJBU management software, please refer to the “Fujitsu Battery Unit" user guide. 6.4.2 Removing the FJBU...
Page 123: Preliminary Steps
Power supply unit (PSU) Ê Push the lock spring inward to unlock the CMA stopper (see figure 31). CAUTION! In case of not enough space at the under side, unlock the CMA stopper of the server below and pull out the CMA to the rear side Ê...
Page 124: Installing The Dummy Cover
Power supply unit (PSU) 6.4.2.3 Installing the dummy cover Figure 42: Installing the dummy cover Ê Insert the dummy cover into the empty bay with the impressed arrow symbol facing to the top (see circle). Ensure that the upper rear cant of the dummy cover fits under the PSU cage. Ê...
Page 125: Preliminary Steps
Power supply unit (PSU) Ê Remove the CMA stopper with the mounted crossbar (see figure 32). Ê Hold the CMA stopper, the crossbar and the CMA including cables in the one hand. Ê Remove the FJBU and install the new FJBU carefully. Ê...
Page 126: Converting A Standard Psu To A Redundant Psu
Power supply unit (PSU) Converting a standard PSU to a redundant The standard PSU can be replaced by a redundant PSU. The redundant PSU consists of up to two PSUs (slide-in units). The upgrade kit contains only one PSU (for PSU redundancy the second PSU must be additionally ordered). The upgrade kit for the redundant PSU consists of the following parts: –...
Page 127: Installing The Upgrade Kit
Power supply unit (PSU) Figure 43: Removing the adapter plate Ê Remove the screw (see circle) which attach the adapter plate of the PSU to the housing. Ê Push the adapter plate a few centimeters inward to detach it from the two bolts (see close-ups).
Page 128 Power supply unit (PSU) Figure 45: Inserting the PSU cage Ê Insert the PSU cage in the housing and push it to the rear side. CAUTION! The PSU cage must engage in the five bolts (positions see figure 44). Three bolts are shown as examples in the close-ups. Figure 46: Fastening the PSU cage Ê...
Page 129 Power supply unit (PSU) Installing the power distribution board Figure 47: Folding the flat cable Ê Fold the flat cable as shown. Ê Install the power distribution board as described in section "Installing the new power distribution board" on page 119.
Page 130 Power supply unit (PSU) Installing hot-plug PSU and dummy cover Ê Install the PSU as described in section "Installing a hot-plug PSU" on page 110. The PSU must be installed in the first bay (left bay seen from rear side). The dummy cover must be installed in the second bay. Ê...
Page 131: Concluding Steps
Power supply unit (PSU) Figure 51: Installing fan module 5 Ê Press down the four rubber pins until they engage (see circles). Ê Connect the fan cable to connector "FAN5" on the system board. For the cable plan see section "Cabling plans"...
Page 132 Power supply unit (PSU) Upgrade and Maintenance Manual RX1330 M3...
Page 133: Hard Disk Drive (Hdd) / Solid State Drive (Ssd)
Hard disk drive (HDD) / solid state drive (SSD) Safety notes CAUTION! The HDD or SSD must not be removed from the installation frame by ● anyone except a service technician. The HDD/SSD modules (drives) must all be marked clearly so that ●...
Page 134: Basic Information
Hard disk drive (HDD) / solid state drive (SSD) Basic information The HDD or SSD and the installation frame together make up the HDD module or SSD module. The server is shipped with one of the following HDD or SSD subsystems: –...
Page 135: Handling Hdds Or Ssds Without Installation Frame
Hard disk drive (HDD) / solid state drive (SSD) 7.1.1 Handling HDDs or SSDs without installation frame 7.1.1.1 2.5-inch HDD/SSD and 2.5-inch installation frame Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: Phillips PH1 / (+) No. 1 screw driver Installing a 2.5-inch HDD/SSD in a 2.5-inch installation frame Figure 52: Installing the 2.5-inch HDD/SSD in the 2.5-inch installation frame (A) Ê...
Page 136 Hard disk drive (HDD) / solid state drive (SSD) Figure 53: Installing the 2.5-inch HDD/SSD in the 2.5-inch installation frame (B) Ê Fasten the 2.5-inch HDD/SSD with four screws. Removing a 2.5-inch HDD/SSD from a 2.5-inch installation frame Ê Please proceed in reversed order. Upgrade and Maintenance Manual RX1330 M3...
Page 137: Inch Hdd/Ssd And 3.5-Inch Installation Frame
Hard disk drive (HDD) / solid state drive (SSD) 7.1.1.2 2.5-inch HDD/SSD and 3.5-inch installation frame Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: Phillips PH1 / (+) No. 1 screw driver In order to use 2.5-inch HDD/SSD, you can install a 2.5-inch HDD/SSD in the 3.5-inch installation frame.
Page 138 Hard disk drive (HDD) / solid state drive (SSD) Figure 55: Installing the 2.5-inch HDD/SSD in the 3.5-inch installation frame (A) Figure 56: Installing the 2.5-inch HDD/SSD in the 3.5-inch installation frame (B) Ê Fasten the 2.5-inch HDD/SSD with four screws. Removing a 2.5-inch HDD/SSD from a 3.5-inch installation frame Ê...
Page 139: Inch Hdd And 3.5-Inch Installation Frame
Hard disk drive (HDD) / solid state drive (SSD) 7.1.1.3 3.5-inch HDD and 3.5-inch installation frame Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: Phillips PH1 / (+) No. 1 screw driver Installing a 3.5-inch HDD in a 3.5-inch installation frame Figure 57: Installing the 3.5-inch HDD in the 3.5-inch installation frame (A) Ê...
Page 140 Hard disk drive (HDD) / solid state drive (SSD) Figure 58: Installing the 3.5-inch HDD in the 3.5-inch installation frame (B) Ê Fasten the 3.5-inch HDD with four screws. Removing a 3.5-inch HDD from a 3.5-inch installation frame Ê Please proceed in reversed order. Upgrade and Maintenance Manual RX1330 M3...
Page 141: Inch Hdd/Ssd Configurations
Hard disk drive (HDD) / solid state drive (SSD) 2.5-inch HDD/SSD configurations 7.2.1 Equipping the 2.5-inch HDDs/SSDs – SSDs are always equipped before installing HDDs. – If only one HDD/SSD module is installed, the HDD/SSD module will be installed in position 1. Free bays must be equipped with a dummy module. 7.2.2 Configuration with up to four HDD/SSD modules Figure 59: Configuration with up to four 2.5-inch HDDs/SSDs...
Page 142: Configuration With Up To Eight Hdd/Ssd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.2.3 Configuration with up to eight HDD/SSD modules Figure 60: Configuration with up to eight HDDs/SSDs The HDD/SSD numbering as listed in the ServerView RAID Manager: Position Logical drive number ServerView RAID Manager display name Vendor Product (0) Vendor Product (1) Vendor Product (2)
Page 143: Configuration With Up To 10 Hdd/Ssd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.2.4 Configuration with up to 10 HDD/SSD modules Figure 61: Configuration with up to 10 HDDs/SSDs The HDD/SSD numbering as listed in the ServerView RAID Manager: Position Logical drive number ServerView RAID Manager display name Vendor Product (0) Vendor Product (1) Vendor Product (2)
Page 144: Installing 2.5-Inch Hdd/Ssd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.2.5 Installing 2.5-inch HDD/SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.2.5.1 Preliminary steps Ê Locate the correct drive bay as described in section "2.5-inch HDD/SSD configurations" on page 141.
Page 145: Installing A 2.5-Inch Hdd/Ssd Module
Hard disk drive (HDD) / solid state drive (SSD) Figure 63: Removing a 2.5-inch dummy module Ê Press both tabs together (1) and pull the dummy module out of its bay (2). CAUTION! Save the dummy module for future use. Always replace dummy modules into unused HDD/SSD bays to comply with applicable EMC regulations and satisfy cooling requirements.
Page 146: Concluding Steps
Hard disk drive (HDD) / solid state drive (SSD) Figure 65: Installing the 2.5-inch HDD/SSD module Ê Insert the HDD/SSD module into a drive bay and carefully push back as far as it will go (1). Ê Close the locking lever to lock the HDD in place (2). Ê...
Page 147: Removing 2.5-Inch Hdd/Ssd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.2.6 Removing 2.5-inch HDD/SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.2.6.1 Preliminary steps Ê If the HDD/SSD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure Only remove an HDD module combined in a RAID 0 array if...
Page 148: Removing A 2.5-Inch Hdd/Ssd Module
Hard disk drive (HDD) / solid state drive (SSD) For further information, please refer to the "ServerView Suite RAID Management" user guide. 7.2.6.2 Removing a 2.5-inch HDD/SSD module Ê Pinch the green locking clips and open the locking lever (see figure 64). Ê...
Page 149: Replacing A 2.5-Inch Hdd/Ssd Module
Hard disk drive (HDD) / solid state drive (SSD) 7.2.7 Replacing a 2.5-inch HDD/SSD module Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! Only remove an HDD/SSD module during operation if the drive is not ● currently being accessed. Observe the indicators for the corresponding HDD/SSD modules, see section "Indicators on the hot-plug HDD module"...
Page 150: Preliminary Steps
Hard disk drive (HDD) / solid state drive (SSD) 7.2.7.1 Preliminary steps "Locating the defective server" on page 50 Ê "Locating the defective component" on page 51 Ê 7.2.7.2 Removing the defective 2.5-inch HDD/SSD module Ê Remove the HDD/SSD module as described in section "Removing 2.5-inch HDD/SSD modules"...
Page 151: Replacing The 4 X 2.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) 7.2.8 Replacing the 4 x 2.5-inch HDD backplane Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: tool-less 7.2.8.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 152 Hard disk drive (HDD) / solid state drive (SSD) Left side 4 x 2.5-inch HDD backplane (A3C40196780) Figure 67: Releasing the ODD latch and disconnecting the cables Ê If applicable, disconnect both cables from the ODD (see orange circle). Ê If applicable, pull the ODD latch upward (1) until it disengages and push the ODD somewhat in direction of the front side (2).
Page 153: Installing The New 4 X 2.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) Right side 4 x 2.5-inch HDD backplane (A3C40196777) Figure 69: Removing the 4 x 2.5-inch HDD backplane Ê Disconnect all cables from the HDD backplane (see orange arrows). If applicable, remove the OOB cable from the HDD backplane, too. Ê...
Page 154 Hard disk drive (HDD) / solid state drive (SSD) Right side 4 x 2.5-inch HDD backplane (A3C40196777) Figure 70: Installing the 4 x 2.5-inch HDD backplane Ê Position the HDD backplane on the four hooks (see circles). Ê Push the HDD backplane downward. Make sure that the HDD backplane fits in the guides (A).
Page 155 Hard disk drive (HDD) / solid state drive (SSD) Left side 4 x 2.5-inch HDD backplane (A3C40196780) Figure 71: Installing the 4 x 2.5-inch HDD backplane Ê Position the HDD backplane on the six hooks (see circles). Ê Push the HDD backplane downward. Make sure that the HDD backplane fits in the guides (A).
Page 156: Concluding Steps
Hard disk drive (HDD) / solid state drive (SSD) Figure 72: Connecting the cables to the ODD and the 4 x 2.5-inch HDD backplane Ê If applicable, push the ODD in its bay until the ODD latch engages (see orange arrow). Ê...
Page 157: Replacing The 10 X 2.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) 7.2.9 Replacing the 10 x 2.5-inch HDD backplane Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver (for removing/installing SAS expander board) 7.2.9.1 Preliminary steps "Locating the defective server"...
Page 158 Hard disk drive (HDD) / solid state drive (SSD) Figure 74: Disconnecting SAS cables Ê Disconnect the two SAS cables from the SAS expander board. Figure 75: Removing the SAS expander board (A) Ê Remove the two screws from the SAS expander board (see circles). Upgrade and Maintenance Manual RX1330 M3...
Page 159: Removing The Defective 10 X 2.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) Figure 76: Removing the SAS expander board (B) Ê Get the SAS expander board out of the two connectors of the HDD backplane and remove it. CAUTION! Lift up the SAS expander board while removing it in order to prevent the components to be damaged by the stand-offs of the chassis (see orange arrows).
Page 160: Installing The New 10 X 2.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) 7.2.9.4 Installing the new 10 x 2.5-inch HDD backplane Figure 78: Installing the 10 x 2.5-inch HDD backplane Ê Position the HDD backplane on the six hooks (see circles). Ê Push the HDD backplane downward. Make sure that the HDD backplane fits in the guides (A).
Page 161 Hard disk drive (HDD) / solid state drive (SSD) Figure 80: Installing the SAS expander board (B) Ê Fasten the SAS expander board with two screws (see circles). MLC 2 MLC 1 Figure 81: Connecting SAS cables Ê Connect the two SAS cables to the SAS expander board: –...
Page 162: Concluding Steps
Hard disk drive (HDD) / solid state drive (SSD) Figure 82: Connecting power cable to the HDD backplane Ê Connect the power cable to the HDD backplane. 7.2.9.6 Concluding steps Ê Insert all HDD/SSD modules, see section "Installing a 2.5-inch HDD/SSD module"...
Page 163: Replacing The Sas Expander Board
Hard disk drive (HDD) / solid state drive (SSD) 7.2.10 Replacing the SAS expander board Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 7.2.10.1 Preliminary steps "Locating the defective server" on page 50 Ê...
Page 164: Upgrading Configuration From Up To Four To Up To Eight 2.5-Inch Hdds/Ssds
Hard disk drive (HDD) / solid state drive (SSD) 7.2.11 Upgrading configuration from up to four to up to eight 2.5-inch HDDs/SSDs Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less CAUTION! All data on all HDDs/SSDs in the array will be lost when deleting the RAID array! Be sure to back up your data before deleting a RAID array.
Page 165: Installing The Second Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) Figure 84: Removing the ODD lock (B) Ê Remove the ODD lock. 7.2.11.3 Installing the second HDD backplane Ê Install the second HDD backplane as described in section "Left side 4 x 2.5- inch HDD backplane (A3C40196780)"...
Page 166 Hard disk drive (HDD) / solid state drive (SSD) Figure 86: Connecting OOB cable (example with 2nd 2.5-inch HDD backplane) Figure 87: Connecting OOB cable (example without 2nd 2.5-inch HDD backplane) Ê If applicable, connect the OOB cable to HDD backplanes. Ê...
Page 167: Installing Additional Hdd/Ssd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.2.11.4 Installing additional HDD/SSD modules Ê Remove the dummy locks as described in section "Removing a 2.5-inch HDD/SSD dummy module" on page 144. Ê Insert additional HDD/SSD modules as described in section "Installing 2.5- inch HDD/SSD modules"...
Page 168: Inch Hdd Configurations
Hard disk drive (HDD) / solid state drive (SSD) 3.5-inch HDD configurations 7.3.1 Equipping the 3.5-inch HDDs – If only one HDD module is installed, the HDD module will be installed in the left bay (seen from the front) and dummy modules must be installed in the free bays.
Page 169: Installing 3.5-Inch Hdd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.3.2 Installing 3.5-inch HDD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.3.2.1 Preliminary steps Ê Locate the correct drive bay as described in section "3.5-inch HDD configurations" on page 168.
Page 170: Installing A 3.5-Inch Hdd Module
Hard disk drive (HDD) / solid state drive (SSD) 7.3.2.3 Installing a 3.5-inch HDD module Figure 90: Opening the 3.5-inch HDD module locking lever Ê Pinch the green locking clip (1) and open the locking lever (2). Figure 91: Installing the 3.5-inch HDD module Ê...
Page 171: Removing 3.5-Inch Hdd Modules
Hard disk drive (HDD) / solid state drive (SSD) 7.3.3 Removing 3.5-inch HDD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.3.3.1 Preliminary steps Ê If the HDD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure Only remove an HDD module combined in a RAID 0 array if...
Page 172: Removing A 3.5-Inch Hdd Module
Hard disk drive (HDD) / solid state drive (SSD) 7.3.3.2 Removing a 3.5-inch HDD module Ê Pinch the green locking clips and open the locking lever (see figure 90). Ê Pull the HDD module out a few centimeters. Ê Wait about 30 seconds to allow the HDD to spin down. This period is necessary for the RAID controller to recognize that an HDD module has been removed and for the HDD to come to a stop.
Page 173: Replacing A 3.5-Inch Hdd Module
Hard disk drive (HDD) / solid state drive (SSD) 7.3.4 Replacing a 3.5-inch HDD module Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! Only remove an HDD module during operation if the drive is not ● currently being accessed. Observe the indicators on the HDD module, see section "Indicators on the hot-plug HDD module"...
Page 174: Preliminary Steps
Hard disk drive (HDD) / solid state drive (SSD) 7.3.4.1 Preliminary steps "Locating the defective server" on page 50 Ê "Locating the defective component" on page 51 Ê 7.3.4.2 Removing the defective 3.5-inch HDD module Ê Remove the HDD module as described in section "Removing a 3.5-inch HDD module"...
Page 175: Replacing The 3.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) 7.3.5 Replacing the 3.5-inch HDD backplane Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: tool-less 7.3.5.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 176: Removing The Defective 3.5-Inch Hdd Backplane
Hard disk drive (HDD) / solid state drive (SSD) 7.3.5.2 Removing the defective 3.5-inch HDD backplane Ê Disconnect all cables from the HDD backplane. If applicable, remove the OOB cable from the HDD backplane, too. Ê If applicable, disconnect the ODD power and SATA cable to make room to remove the HDD backplane easier.
Page 177: Concluding Steps
Hard disk drive (HDD) / solid state drive (SSD) Figure 95: Connecting the cables to the 3.5-inch HDD backplane Ê Connect the following cables to the HDD backplane: – SAS/SATA data cable: (1), (2), (4), (5) to connectors "P1", "P2", "P3", "P4" according to the length (6) plug P6 to connector "SGPIO"...
Page 178 Hard disk drive (HDD) / solid state drive (SSD) Upgrade and Maintenance Manual RX1330 M3...
Page 179: Fans
Fans Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices inside the server remain hot after shutdown. Wait for a while ● after shutdown before installing or removing internal options. The circuit boards and soldered parts of internal options are exposed ●...
Page 180: Basic Information
Fans Basic information Base units with a standard PSU are supplied with four fan modules without redundancy. CAUTION! In the configuration with four fan modules, defective system fans have to be replaced immediately. Base units with a redundant PSU are supplied with five fan modules in a 1 of 5 redundancy.
Page 181: Replacing A Defective Fan Module
Fans Replacing a defective fan module Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: tool-less 8.2.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 182: Installing The New Fan Module
Fans Figure 98: Removing the fan module Ê Push the fan cable through the opening of the fan cage. Ê Take out the fan module. 8.2.3 Installing the new fan module Figure 99: Installing the fan module Ê Thread the fan cable through the opening of the fan cage (see close-up) and insert the fan module.
Page 183: Concluding Steps
Fans Figure 100: Connecting the fan cable Ê Press down the four rubber pins until they engage (A). Ê Connect the fan cable to the system board. 8.2.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê...
Page 184 Fans Upgrade and Maintenance Manual RX1330 M3...
Page 185: Expansion Cards And Backup Units
Expansion cards and backup units Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.
Page 186: Basic Information
Expansion cards and backup units Basic information FRONTPANEL1 PC98 Riser card (x8) USB 3.0 Slot3 PWR1 Battery USB 3.0 USB3.0 FRONT USB 3.0 USB 3.0 Intel C236 COM1 HDD LED FAN2 SYS Slot2 DIMM2A Riser card (x4) DIMM1A Riser card (x8) DIMM2B Slot1 DIMM1B...
Page 187 Adapter Adapter Product Name Max # Customer 2 n/a Sequence Vendor Description (Softwarepool) Adapter Order No. if 3FH Controller Crad- TPM Fujitsu TPM 1.2 Module (D3127-A1x) S26361-F3552- Technology L6,S2... Solutions Fujitsu TPM 2.0 Module (D3467) S26361-F3552- Technology L10,S... Solutions Controller Card – Graphic...
Page 188: Handling Slot Brackets
Expansion cards and backup units Handling slot brackets 9.2.1 Installing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Use the low profile bracket perforated for relevant controllers. Figure 102: Perforated and non-perforated slot brackets Full height bracket non-perforated Full height bracket perforated Low profile bracket perforated...
Page 189 Expansion cards and backup units Example network adapter Figure 103: Placing the slot bracket Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel (2).
Page 190: Removing A Slot Bracket
Expansion cards and backup units 9.2.2 Removing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 9.2.2.1 Removing the slot bracket Ê Remove the two screws. Ê Remove the controller from the mounting tabs on the slot bracket. Upgrade and Maintenance Manual RX1330 M3...
Page 191: Handling Sfp+ Transceiver Modules
Expansion cards and backup units Handling SFP+ transceiver modules For Fiber Channel over Ethernet (FCoE) configurations, the ethernet server adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules. 9.3.1 Installing SFP+ transceiver modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less...
Page 192 Expansion cards and backup units Figure 106: Unlatching the locking bail Ê Carefully unlatch and fold down the locking bail on the SFP+ transceiver module. Inserting the SFP+ transceiver module Figure 107: Inserting the SFP+ transceiver module Ê Insert and slide the SFP+ transceiver module into the socket connector as far as it will go.
Page 193 Expansion cards and backup units Figure 108: Latching the locking bail Ê Carefully fold up and latch the locking bail. Figure 109: Installing the protective optical port plug Ê If the SFP+ transceiver module is not immediately connected to an LC connector, attach the protective optical port plug to the transceiver optical bores.
Page 194: Removing An Sfp+ Transceiver Module
Expansion cards and backup units Installing the secondary SFP+ transceiver module Figure 110: Installing the secondary SFP+ transceiver module Ê If applicable, install the secondary SFP+ transceiver module accordingly. 9.3.2 Removing an SFP+ transceiver module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less For Fiber Channel over Ethernet (FCoE) configurations, the ethernet server...
Page 195 Expansion cards and backup units Figure 111: Removing the protective optical port plug Ê If present, remove the protective optical port plug from the SFP+ transceiver module. CAUTION! Save the protective port plug for future use. Figure 112: Unlatching the locking bail Ê...
Page 196 Expansion cards and backup units Figure 113: Removing the SFP+ transceiver module Ê Pull the SFP+ transceiver module out of its socket connector. Ê Attach the protective optical port plug to the transceiver optical bores. Place the removed SFP+ transceiver module in an antistatic bag or other protective environment.
Page 197: Expansion Cards And Riser Cards
Expansion cards and backup units Expansion cards and riser cards 9.4.1 Installing an expansion card Upgrade and Repair Unit Hardware: 10 minutes (URU) Software: 5 minutes Tools: tool-less 9.4.1.1 Preliminary steps "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê...
Page 198: Installing The Expansion Card
Expansion cards and backup units CAUTION! Keep the slot cover for future use. If the expansion card is removed and not replaced with a new one, the slot cover must be reinstalled due to cooling, to comply with applicable EMC regulations and to protect against fire.
Page 199: Removing An Expansion Card
Expansion cards and backup units 9.4.2 Removing an expansion card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 9.4.2.1 Preliminary steps "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 200: Installing The Slot Cover
Expansion cards and backup units 9.4.2.3 Installing the slot cover Figure 117: Installing the slot cover - example riser module 1 Ê Insert the slot cover. Make sure that the lug on the slot cover (A) clicks into place in the corresponding hole. 9.4.2.4 Concluding steps Ê...
Page 201: Replacing An Expansion Card
Expansion cards and backup units 9.4.3 Replacing an expansion card Upgrade and Repair Unit Hardware: 10 minutes (URU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver (only for replace the slot bracket) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values.
Page 202: Removing An Expansion Card
Expansion cards and backup units 9.4.3.2 Removing an expansion card Ê Remove the expansion card as described in section "Removing the expansion card" on page 199. Ê If the slot bracket on the defective expansion card is to be reused, remove it from the expansion card as described in section "Removing a slot bracket"...
Page 203 Expansion cards and backup units Ê If applicable, reconfigure your network settings in the operation system according to the original configuration of the replaced controller (expansion card or onboard). Configuration of network settings should be performed by the customer. For further information, please refer to section "Note on network settings recovery"...
Page 204: Replacing A Riser Card
Expansion cards and backup units 9.4.4 Replacing a riser card Field Replaceable Unit Hardware: 5 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 9.4.4.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 205: Installing The Riser Card
Expansion cards and backup units 9.4.4.3 Installing the riser card Figure 119: Installing the riser card - example riser module 1 Ê Insert the riser card (1). Ê Fasten the riser card with two screws (2). Ê Install the expansion card as described in section "Installing the expansion card"...
Page 206: Replacing A Tfm
Expansion cards and backup units 9.4.5 Replacing a TFM Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver 9.4.5.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 207 Expansion cards and backup units Figure 121: Removing the TFM Ê Remove the two screws (1). Ê Remove the TFM (2). Note for replacing the TFM: The two spacer bolts can remain on the RAID controller. Upgrade and Maintenance Manual RX1330 M3...
Page 208: Installing The New Tfm
Expansion cards and backup units 9.4.5.3 Installing the new TFM Example RAID controller Figure 122: Installing the TFM (A) Ê If no TFM has been installed before: fit the two spacer bolts on the RAID controller. Upgrade and Maintenance Manual RX1330 M3...
Page 209: Concluding Steps
Expansion cards and backup units Figure 123: Installing the TFM (B) Ê Secure the TFM on the RAID controller with the two screws from the TFM kit. Figure 124: Connecting the FBU adapter cable Ê Connect the FBU adapter cable to the TFM. Ê...
Page 210: Upgrading To The Full Height Riser Module
Expansion cards and backup units 9.4.6 Upgrading to the full height riser module Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Figure 125: Upgrade kit Full height riser module Extension bracket Screw 9.4.6.1 Preliminary steps...
Page 211: Installing The Upgrade Kit
Expansion cards and backup units 9.4.6.2 Installing the upgrade kit Figure 126: Removing the riser module support Ê Remove the screw (1). Ê Remove the riser module support (2). Ê Remove the riser card from riser module 3 as described in section "Removing the riser card"...
Page 212 Expansion cards and backup units Figure 128: Installing the expansion card - example full height riser module Ê Install the expansion card as described in section "Installing the expansion card" on page 198. Figure 129: Installing the extension bracket Ê Fasten the extension bracket with one screw to the full height riser module (see circle).
Page 213 Expansion cards and backup units Figure 130: Installing the full height riser module Ê Insert the riser card into the system board slot and press down the green touch points (see circles). CAUTION! Make sure that the EMC springs make contact correctly (see close-ups). Upgrade and Maintenance Manual RX1330 M3...
Page 214: Flash Backup Unit (Fbu)
Expansion cards and backup units Flash Backup Unit (FBU) The FBU backs up the memory contents of the RAID controller in the event of a power failure. You can install one FBU. 9.5.1 Installing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH1 / (+) No.
Page 215 Expansion cards and backup units Ê At a slight angle, fit the FBU under both retaining brackets of the holder. Ê Push in the FBU until it locks in place. Figure 132: Installing the FBU in the holder (B) Ê Ensure that the FBU is properly seated in the holder as shown. Figure 133: Connecting the FBU adapter cable to the FBU Ê...
Page 216: Installing The Fbu
Expansion cards and backup units 9.5.1.3 Installing the FBU Figure 134: Position of the shoulder screw caps Figure 135: Installing the FBU with the holder Ê Insert the holder into the chassis so that the three shoulder screw caps on the chassis floor rest in the wide ends of the keyhole slots on the holder.
Page 217: Concluding Steps
Expansion cards and backup units Ê If applicable, install the TFM as described in section "Installing the new TFM" on page 208. Ê Connect the FBU adapter cable to the TFM as described in section "Installing the new TFM" on page 208.
Page 218: Removing An Fbu
Expansion cards and backup units 9.5.2 Removing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less CAUTION! Dispose of used battery properly. Keep away from children. ● Do not throw flash backup units into the trash can. Batteries must be ●...
Page 219: Disconnecting The Fbu Cable From The Fbu
Expansion cards and backup units Ê Lift the holder out of the chassis. 9.5.2.3 Disconnecting the FBU cable from the FBU Figure 138: Disconnecting the FBU cable from the FBU Ê Disconnect the FBU cable from the FBU. 9.5.2.4 Removing the FBU from the holder Figure 139: Removing the FBU from the holder Ê...
Page 220: Concluding Steps
Expansion cards and backup units 9.5.2.5 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê 9.5.3 Replacing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less CAUTION!
Page 221: Installing The New Fbu
Expansion cards and backup units 9.5.3.3 Installing the new FBU Ê Install the FBU in the holder and connect the FBU adapter cable to the FBU as described in section "Preparing the FBU" on page 214. Ê Install the FBU with the holder as described in section "Installing the FBU"...
Page 222 Expansion cards and backup units Upgrade and Maintenance Manual RX1330 M3...
Page 223: Main Memory
Main memory Safety notes CAUTION! Do not install unsupported third party memory modules. For further ● information on supported memory modules, refer to section "Basic information" on page 224. Memory modules remain hot after shutdown. Wait for components to ● cool down before installing or removing memory modules to prevent burns.
Page 224: Basic Information
Main memory 10.1 Basic information Slot2 DIMM2A Riser card (x4) DIMM1A Riser card (x8) DIMM2B Slot1 DIMM1B Standard Intel i210 SATA5 SATA1-4 Shared Jumper iRMC Intel Indicate SATA6 i210 Front Micro Managem. I2C5 Service PWR4 Figure 140: Slots of the main memory The system board offers four slots for memory modules.
Page 225: Modes Of Operation
Main memory 10.1.1.2 Modes of operation – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory. The DRAM device technology (1Gbit / 2Gbit / 4Gbit) may vary from one channel to the other.
Page 226: Installing A Memory Module
Main memory 10.2 Installing a memory module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.2.1 Preliminary steps "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 227: Concluding Steps
Main memory Figure 142: Installing a memory module Ê Align the notch on the bottom of the module with the crossbar in the slot. Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module. 10.2.4 Concluding steps "Reassembling"...
Page 228: Removing A Memory Module
Main memory 10.3 Removing a memory module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 229: Concluding Steps
Main memory 10.3.3 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resuming BitLocker functionality" on page 95 Ê 10.4 Replacing a memory module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less...
Page 230: Concluding Steps
Main memory 10.4.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resetting the error status after replacing memory modules or CPUs" on Ê page 86 "Enabling replaced components in the system BIOS"...
Page 231: Processor (Cpu)
Processor (CPU) Safety notes CAUTION! Do not install unsupported CPUs. For further information on ● supported CPUs, refer to section "Supported CPUs" on page 232. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.
Page 232: Basic Information
Quad-Core Xeon E3-12xxv6 or one Dual Core i3-7xxx or one Dual Core Pentium G4xxx CPU – one CPU socket LGA 1151 For system relevant information, refer to your server’s hardware configurator available online at the following address: http://ts.fujitsu.com/products/standard_servers/index.htm For Japan: http://jp.fujitsu.com/platform/server/primergy/system/ 11.2 Upgrading or replacing the CPU...
Page 233: Removing The Heat Sink
Processor (CPU) "Getting access to the component" on page 55 Ê "Removing a riser module" on page 66 Ê 11.2.2 Removing the heat sink Figure 145: Removing the heat sink Ê Loosen the four screws of the heat sink in a crossover pattern according to the numbering.
Page 234: Removing The Cpu
Processor (CPU) 11.2.3 Removing the CPU Figure 146: Unlatching the socket lever Ê Unlatch the socket lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Figure 147: Removing the CPU Ê...
Page 235: Installing The Cpu
Processor (CPU) 11.2.4 Installing the CPU Ê Confirm that the CPU model number printed on the top of the CPU fits with the requirements. Ê If applicable, remove the protective cap from the bottom side of the CPU. Figure 148: Installing the CPU Ê...
Page 236 Processor (CPU) Figure 149: Closing the load plate (A) Ê Lower the load plate over the CPU while leaving the socket lever in the open position. Figure 150: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.
Page 237 Processor (CPU) Figure 151: Latching the socket lever Ê Latch the socket lever under the load plate tab. Upgrade and Maintenance Manual RX1330 M3...
Page 238: Applying The Thermal Paste
Processor (CPU) 11.2.5 Applying the thermal paste For Japan the service engineer must follow the instruction provided separately. If the CPU upgrade or replacement kit contains a new heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
Page 239 Processor (CPU) Figure 153: Applying the thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the CPU surface as shown. CAUTION! Do not mix different types of thermal paste. Upgrade and Maintenance Manual RX1330 M3...
Page 240: Installing The Heat Sink
Processor (CPU) 11.2.6 Installing the heat sink Figure 154: Installing the heat sink Ê Ensure that the heat sink cooling fins match the direction of the airflow! Ê Carefully seat the heat sink on the four threaded holes as shown. CAUTION! –...
Page 241: Concluding Steps
Processor (CPU) 11.2.7 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê When the system is powered on after a CPU has been replaced or upgraded, the Global Error indicator will start flashing with the error message CPU has been changed.
Page 242: Replacing The Heat Sink
Processor (CPU) 11.3 Replacing the heat sink Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 11.3.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 243: Concluding Steps
Processor (CPU) 11.3.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê Upgrade and Maintenance Manual RX1330 M3...
Page 244 Processor (CPU) Upgrade and Maintenance Manual RX1330 M3...
Page 245: Accessible Drives
Accessible drives Safety notes CAUTION! Before installing an accessible drive, acquaint yourself with the ● drive's user documentation. When inserting an accessible drive into the server, ensure not to ● pinch or strain any connected cables. When installing an accessible drive, hold it by its sides. Applying force ●...
Page 246: Basic Information
Accessible drives 12.1 Basic information You can install one 5.25-inch slimline ODD. The installation bay depends on the 2.5-inch or 3.5-inch HDD configuration. The proceeding for installing/removing is identic except the routing of the cables and the depending ODD power connector on the system board (see section "Onboard connectors"...
Page 247 Accessible drives 2.5-inch HDD configuration Figure 157: Position of the ODD bay - example 2.5-inch HDD configuration Figure 158: Routing ODD cables - example 2.5-inch HDD configuration Upgrade and Maintenance Manual RX1330 M3...
Page 248: Optical Disk Drive (Odd)
Accessible drives 12.2 Optical disk drive (ODD) 12.2.1 Installing the ODD Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver 12.2.1.1 Preliminary steps "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê...
Page 249: Installing The Odd
Accessible drives CAUTION! Keep the dummy cover for future use. If you remove the accessible drive again and do not replace it with a new one, the dummy cover must be reinstalled to comply with EMC regulations and to satisfy cooling requirements and fire protection measures.
Page 250 Accessible drives Figure 161: Installing the ODD latch on the ODD Ê Fasten the ODD latch with two screws to the rear side of the ODD (see arrow and circles). Figure 162: Installing the ODD Ê Push the ODD into the bay (1) simultaneously pressing the front of the ODD slightly down until the ODD latch engages (2).
Page 251: Concluding Steps
Accessible drives Figure 163: Connecting cables (example with 2nd 2.5-inch HDD backplane) Figure 164: Connecting cables (example without 2nd 2.5-inch HDD backplane) Ê Connect the ODD power cable (1) to the ODD. Ê Connect the SATA cable (2) to the ODD. For the cable plan see section "Cabling plans"...
Page 252: Removing The Odd
Accessible drives 12.2.2 Removing the ODD Field Replaceable Unit Hardware: 5 minutes (FRU) Tools: Phillips PH1 / (+) No. 1 screw driver 12.2.2.1 Preliminary steps "Removing backup and optical disk media" on page 74 Ê "Suspending BitLocker functionality" on page 71 Ê...
Page 253 Accessible drives Figure 166: Disconnecting cables (example without 2nd 2.5-inch HDD backplane) Ê Disconnect the ODD power cable and the SATA cable from the ODD. Figure 167: Removing the ODD Ê Press the ODD latch in direction of the arrow until it disengages (1). Ê...
Page 254: Installing The Dummy Cover
Accessible drives Figure 168: Removing the ODD latch from the ODD Ê Remove the two screws (see circles). Ê Remove the ODD latch (see arrow). Ê If no new ODD will be installed: fasten the ODD latch with two screws to the fan bridge (see figure 160).
Page 255: Concluding Steps
Accessible drives 12.2.2.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resuming BitLocker functionality" on page 95 Ê 12.2.3 Replacing the ODD Field Replaceable Unit Hardware: 5 minutes (FRU) Tools: Phillips PH1 / (+) No.
Page 256: Concluding Steps
Accessible drives 12.2.3.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resuming BitLocker functionality" on page 95 Ê Upgrade and Maintenance Manual RX1330 M3...
Page 257: Front Panel
Front panel Safety notes CAUTION! When inserting the front panel into the server, ensure not to pinch or ● strain any connected cables. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.
Page 258: Front Panel Module
Front panel 13.2 Front panel module 13.2.1 Replacing the front panel module Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: Phillips PH1 / (+) No. 1 screw driver Note on system information backup/restore The front panel contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.
Page 259: Removing The Front Panel Module
Front panel 13.2.1.2 Removing the front panel module Figure 170: Disconnecting the cables (A) Ê Disconnect the front panel cable (1) and the front USB cable (2) from the system board. Figure 171: Disconnecting the cables (B) Ê If applicable, disconnect the front VGA cable (black cable) from the system board.
Page 260 Front panel Figure 172: Removing the front panel module Ê Remove the two screws (1). Ê Pull the front panel module out of its bay (2) until the holder is completely accessible. Figure 173: Removing cables from the front panel module Ê...
Page 261: Installing The Front Panel Module
Front panel Ê If applicable, open the cable tie and disconnect the front VGA cable (3). Please do not cut the cable tie. Ê If applicable, remove the front VGA board with the front VGA connector as described in section "Removing the front VGA board"...
Page 262 Front panel Figure 175: Installing the front panel module Ê Push the front panel module in its bay (1). Ê Fasten the front panel module with two screws (2). Figure 176: Connecting the cables (A) Ê Connect the front panel cable (1) and the front USB cable (2) to the system board.
Page 263: Concluding Steps
Front panel 13.2.1.4 Concluding steps "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Using the Chassis ID Prom Tool" on page 98 Ê "Verifying system information backup / restore" on page 81 Ê...
Page 264: Removing The Dummy Cover
Front panel 13.3.1.2 Removing the dummy cover Figure 178: Removing the dummy cover Ê Remove the dummy cover. CAUTION! Keep the dummy cover for future use. If you remove the front VGA board again and do not replace it with a new one, the dummy cover must be reinstalled to comply with EMC regulations and to satisfy cooling requirements and fire protection measures.
Page 265: Concluding Steps
Front panel 13.3.1.4 Concluding steps "Installing the front panel module" on page 261 Ê "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê 13.3.2 Removing the front VGA board Upgrade and Repair Unit Hardware: 10 minutes (URU)
Page 266: Removing The Front Vga Board
Front panel 13.3.2.2 Removing the front VGA board Figure 180: Removing the front VGA board Ê If the VGA cable was secured with a cable tie, pull out the cable tie (1). Ê Remove the two screws (2) and remove the front VGA board (3). 13.3.2.3 Installing the dummy cover Ê...
Page 267: Replacing The Front Vga Board
Front panel 13.3.3 Replacing the front VGA board Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver 13.3.3.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 268: Front Panel On Qrl (10 X 2.5-Inch Hdd Configuration)
Front panel 13.4 Front panel on QRL (10 x 2.5-inch HDD configuration) 13.4.1 Replacing the front panel on QRL Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: Phillips PH1 / (+) No. 1 screw driver Note on system information backup/restore The front panel contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.
Page 269: Removing The Front Panel On Qrl
Front panel 13.4.1.2 Removing the front panel on QRL The front panel on QRL and the front panel cable are combined in one spare part. Figure 181: Disconnecting the front panel cable Ê Pull up the locking bar (1). Ê Remove the front panel cable (2). Figure 182: Disconnecting the front panel cable (B) Ê...
Page 270 Front panel Figure 183: Removing the front panel on QRL (A) Ê Remove the two screws (see circles). Figure 184: Removing the front panel on QRL (B) Ê Remove the front panel. Ê Pull the front cable out of the opening. Upgrade and Maintenance Manual RX1330 M3...
Page 271: Installing The Front Panel On Qrl
Front panel 13.4.1.3 Installing the front panel on QRL Figure 185: Installing the front panel (A) Ê Thread the front panel cable through the opening. Figure 186: Installing the front panel (B) Ê Position the front panel on the QRL. Ê...
Page 272: Concluding Steps
Front panel Ê Thread the front panel cable through the opening (see figure 182). Figure 187: Connecting the front panel cable (B) Ê Pull up the locking bar (1). Ê Bend the cable 90 degrees by hand for easier routing. Ê...
Page 273: System Board And Components
System board and components Safety notes CAUTION! Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. Circuit boards and soldered parts of internal options are exposed and ●...
Page 274: Cmos Battery
System board and components SATA DOM ● With the Innodisk Serial ATA Disk on Module (SATA DOM) an internal SSD is offered. This SSD can be configured as a boot device or data storage device. iRMC microSD card ● The iRMC microSD card is necessary for using the embedded Lifecycle Management (eLCM) functionality of the iRMC.
Page 275: Preliminary Steps
System board and components 14.2.1.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê "Getting access to the component" on page 55 Ê Ê...
Page 276: Concluding Steps
System board and components 14.2.1.3 Concluding steps Ê Dispose of the CMOS battery in accordance with local regulations concerning special waste. "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê...
Page 277: Installing The Ufm
System board and components 14.3.1.2 Installing the UFM Figure 189: UFM installation kit USB Flash Module (UFM) UFM spacer UFM nylon screw Figure 190: Position on the system board Upgrade and Maintenance Manual RX1330 M3...
Page 278: Concluding Steps
System board and components Figure 191: Installing the UFM Ê Connect the UFM to the system board. The UFM spacer must click into the hole on the system board. 14.3.1.3 Concluding steps Ê Install the riser module 3 as described in section "Installing a riser module"...
Page 279: Removing The Ufm
In order to setup the ESXi, please refer to the corresponding version of the "VMware vSphere Software Description" from the following URL and reinstall ESXi to the USB Flash Module. http://jp.fujitsu.com/platform/server/primergy/software/vmware/manual/ 14.3.2 Removing the UFM Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: –...
Page 280: Removing The Ufm
System board and components 14.3.2.2 Removing the UFM Figure 192: Removing the UFM Ê Remove the nylon screw of the UFM (1). Ê Disconnect and remove the UFM (2). The UFM spacer remains on the system board. Figure 193: Remaining UFM spacer CAUTION! UFM contains customer information (e.g.
Page 281: Concluding Steps
System board and components Figure 194: Tools for breaking the UFM Figure 195: UFM breaking method Ê Use a flat nose pliers and a combination pliers to break the UFM in half as shown in the figure. 14.3.2.3 Concluding steps Ê...
Page 282: Replacing The Ufm
System board and components 14.3.3 Replacing the UFM Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: – Phillips PH1 / (+) No. 1 screw driver – combination pliers and flat nose pliers 14.3.3.1 Preliminary steps "Locating the defective server" on page 50 Ê...
Page 283: Installing The New Ufm
System board and components 14.3.3.3 Installing the new UFM Figure 196: Removing the UFM spacer Ê Remove the nylon screw from the UFM (1). Ê Remove the UFM spacer (2). Figure 197: Installing the UFM Ê Connect the UFM to the system board and the remaining UFM spacer (1). Ê...
Page 284: Concluding Steps
System board and components 14.3.3.4 Concluding steps Ê Install the riser module 3 as described in section "Installing a riser module" on page "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê...
Page 285: Trusted Platform Module (Tpm)
System board and components 14.4 Trusted Platform Module (TPM) 14.4.1 Installing the TPM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: – Bit screw driver – TPM bit insert For Japan: – TPM module fixing tool (S26361-F3552-L909) 14.4.1.1 Preliminary steps "Suspending BitLocker functionality"...
Page 286: Installing The Tpm
System board and components 14.4.1.2 Installing the TPM Figure 198: TPM installation kit TPM (Trusted Platform Module) Special screw for TPM TPM spacer TPM bit insert for TPM special screw The black TPM spacer is not used in this server. Slot2 DIMM2A Riser card (x4)
Page 287: Concluding Steps
System board and components Figure 201: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (for Japan) to a bit screw driver. Figure 202: Installing the TPM Ê Connect the TPM to the system board (1). Ê...
Page 288: Removing The Tpm
System board and components "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resuming BitLocker functionality" on page 95 Ê Ê Enable TPM in the system board BIOS. Proceed as follows: Ê Switch on or restart your server. Ê...
Page 289: Preliminary Steps
For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê...
Page 290: Removing The Tpm
System board and components For detailed information on how to access the BIOS and modify settings, refer to the corresponding BIOS Setup Utility reference manual. "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord"...
Page 291 System board and components CAUTION! Ensure to turn the screw clockwise in order to remove it! Slowly and carefully increase the pressure on the screw until it begins to turn. The effort when loosing the screw should be as low as possible.
Page 292: Concluding Steps
System board and components 14.4.2.3 Concluding steps "Installing the new system board" on page 307 Ê "Reassembling" on page 60 Ê "Connecting the power cord" on page 64 Ê "Switching on the server" on page 66 Ê "Resuming BitLocker functionality" on page 95 Ê...
Page 293: Preliminary Steps
System board and components 14.4.3.1 Preliminary steps "Locating the defective server" on page 50 Ê "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê "Getting access to the component" on page 55 Ê...
Page 294: Sata Dom
System board and components 14.5 SATA DOM 14.5.1 Installing the SATA DOM Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less In the RX1330 M3 two SATA DOM can be installed. In the case of installing the second SATA DOM, no ODD can be used. 14.5.1.1 Preliminary steps "Shutting down the server"...
Page 295: Concluding Steps
System board and components Figure 207: Installing the first SATA DOM Ê Connect the first SATA DOM to the connector "SATA5 DOM" on the system board. Figure 208: Installing the second SATA DOM Ê If applicable, disconnect the SATA cable for an ODD from connector "SATA6 DOM"...
Page 296: Removing The Sata Dom
System board and components 14.5.2 Removing the SATA DOM Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 14.5.2.1 Preliminary steps "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê "Getting access to the component" on page 55 Ê...
Page 297: Replacing The Sata Dom
System board and components 14.5.3 Replacing the SATA DOM Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 14.5.3.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 298: Irmc Microsd Card
System board and components 14.6 iRMC microSD card The iRMC microSD card is necessary for using the Embedded Lifecycle Management (eLCM) functionality of the iRMC. It requires a valid eLCM license key, which is always purchased together with the iRMC microSD card and activated through the iRMC web frontend.
Page 299: Concluding Steps
System board and components Figure 211: Installing the iRMC microSD card Ê With the label facing up, insert the iRMC microSD card into the microSD card slot (1) until it locks in place (2). The onboard position of the microSD card slot can be found in section "Connectors and indicators on the system board"...
Page 300: Removing The Irmc Microsd Card
System board and components Ê Remove the riser module 1 as described in section "Removing a riser module" on page 14.6.2.2 Removing the iRMC microSD card Figure 212: Removing the iRMC microSD card Ê To eject the iRMC microSD card, gently push it in and then let go (1). Ê...
Page 301: Replacing The Irmc Microsd Card
System board and components 14.6.3 Replacing the iRMC microSD card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: a pair of side-cutting pliers 14.6.3.1 Preliminary steps "Locating the defective server" on page 50 Ê "Shutting down the server" on page 53 Ê...
Page 302: System Board
System board and components 14.7 System board 14.7.1 Replacing the system board Field Replaceable Unit Hardware: 40 minutes (FRU) Software: 20 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting CPU socket springs (recommended) Replacing the TPM: –...
Page 303 System board and components CAUTION! – Before replacing the system board, ask the customer whether TPM functionality is used. – If the customer is using TPM functionality, remove the TPM from the old system board and install it on the new system board. Advise your contact persons that they must provide you with all recovery keys which belong to the system to restore them in the TPM later.
Page 304: Preliminary Steps
System board and components 14.7.1.1 Preliminary steps "Locating the defective server" on page 50 Ê "Note on network settings recovery" on page 303 Ê "Suspending BitLocker functionality" on page 71 Ê "Shutting down the server" on page 53 Ê "Disconnecting the power cord" on page 54 Ê...
Page 305: Removing The Defective System Board
System board and components 14.7.1.2 Removing the defective system board Ê Disconnect all cables from the system board. Figure 213: Position of the screws Ê Remove the eight screws from the system board. Upgrade and Maintenance Manual RX1330 M3...
Page 306 System board and components Figure 214: Removing the system board Ê Use both hands to lift the system board carefully out of the chassis in a slight angle. Thereby you pull the connectors out of the connector panel. CAUTION! Always take the system board with both hands! Never lift the system board one-sided or at a heat sink, because the solder connections between the socket and the system board come under tension and increase the risk of damage and malfunction!
Page 307: Installing The New System Board
System board and components 14.7.1.3 Installing the new system board Ê Check the settings on the new system board (see section "Onboard settings" on page 340). Ê Insert the system board by holding it at a slight angle. Slide the connectors into the connector panel (see figure 214 on page 306).
Page 308: Concluding Steps
System board and components 14.7.1.4 Concluding steps "Installing the iRMC microSD card" on page 298 (if applicable) Ê "Installing the SATA DOM" on page 294 (if applicable) Ê "Installing the TPM" on page 285 (if applicable) Ê "Installing the UFM" on page 276 (if applicable) Ê...
Page 309 System board and components "Verifying the system time settings" on page 91 Ê "Updating or recovering the system board BIOS and iRMC" on page 79 Ê Ê If applicable, activate TPM functionality in the system BIOS under Security > TPM (Security Chip) Setting > Security Chip. For more information, refer to the corresponding BIOS Setup Utility reference manual.
Page 310 System board and components Upgrade and Maintenance Manual RX1330 M3...
Page 311: Cables
Cables 15.1 Overview cables The numbers in the cable list correspond to those shown in the cabling plans. Part number Description From - to T26139-Y4015-V301 CBL FRONT_PANEL System board to front panel T26139-Y3959-V301 CBL_HDD_2.5_POWER System board to HDD backplane 1 T26139-Y3990-V301 CBL_ODD_Power System board to ODD power...
Page 312: Cabling Plans
Cables Part number Description From - to T26139-Y4040-V20 CBL_SAS3.0_385 RAID controller to 4x 2.5-inch HDD backplane, rectangle, Expander T26139-Y4031-V103 CBL FBU03 700 RAID controller to FBU T26139-Y4031-V108 CBL_TFM_EP540_750 EP540i / EP580i to FBU T26139-Y2361-V103 CBL_HDD_SIGNAL_220 EP540i / EP580i to System board T26139-Y4040-V71 CBL_4HDD_DATA3.5 L...
Page 313 Cables System Board Front Panel D3375 Front USB 3.0 Panel FRONTPANEL1 Front VGA USB 3.0 FRONT Data Drive Bay 1 FRONT VGA SATA ODD PWR 1 PWR 2 PWR 3 PWR 4 4x 3.5" HDD SATA5 DOM SAS Backplane A3C40157818 SATA6 DOM I2C5 SMBUS...
Page 314 Cables System Board Front D3375 Front Panel Panel (on QRL ) FRONTPANEL1 FRONTPANEL2 USB 3.0 FRONT FRONT VGA MLC1 MLC2 Controller Figure 217: Basic cabling: 10x 2.5-inch HDD Power From PSU Data Standard SATA ODD From PSU Control System Board D3375 PC98 4x 3.5"...
Page 315 Cables Data Redundant PSU Backplane SATA ODD A3C40157835 System Board D3375 PC98 4x 2.5" HDD SAS Backplane L-Shape A3C40196780 PWR 1 SMBUS PWR 2 PWR 3 4x 2.5" HDD SAS Backplane A3C40196777 PWR 4 SMBUS Figure 219: Power cabling: 8x 2.5-inch HDD, redundant PSU Redundant PSU Backplane A3C40157835...
Page 316 Cables System Board D3375 4x 3.5" HDD SATA1-4 SAS Backplane A3C40157818 SATA5 DOM SATA6 DOM SMBUS SGPIO I2C5 Figure 221: Drive/HDD cabling: 4x 3.5-inch HDD onboard controller System Board D3375 SATA1-4 HDD Led 4x 3.5" HDD SAS Backplane A3C40157818 MLC1 C17 / C22 Controller MLC2...
Page 317 Cables System Board D3375 SATA1-4 SATA5 DOM 4x 2.5" HDD SATA6 DOM SAS Backplane A3C40196777 SMBUS I2C5 Figure 223: Drive/HDD cabling: 4x 2.5-inch HDD onboard controller System Board D3375 SATA1-4 HDD Led MLC1 4x 2.5" HDD Controller MLC2 SAS Backplane A3C40196777 C19 / C20 SMBUS...
Page 318 Cables System Board D3375 4x 2.5" HDD SATA1-4 SAS Backplane L-Shape A3C40196780 HDD Led SMBUS MLC1 4x 2.5" HDD Controller MLC2 SAS Backplane A3C40196777 C19 / C20 SMBUS Figure 225: Drive/HDD cabling: 8x 2.5-inch HDD PRAID controller System Board D3375 SATA1-4 10x 2.5"...
Page 319: Appendix
Appendix 16.1 Mechanical overview 16.1.1 Server front Figure 227: Front side 2.5-inch HDDs (up to 4 HDDs) Figure 228: Front side 2.5-inch HDDs (up to 8 HDDs) Figure 229: Front side 2.5-inch HDDs (up to 10 HDDs) Pos. Component ID card Front VGA (option) / dummy cover Front panel and indicators ODD (option) / dummy cover...
Page 320 Appendix Figure 230: Front side 3.5-inch HDDs (up to 4 HDDs) Pos. Component ODD (option) / dummy cover ID card Front VGA (option) / dummy cover Front panel and indicators 4x 3.5-inch HDDs / dummy modules Upgrade and Maintenance Manual RX1330 M3...
Page 321: Server Rear
Appendix 16.1.2 Server rear Figure 231: Rear side (standard PSU) Figure 232: Rear side (redundant PSU) Figure 233: Rear side (redundant PSU and full height riser module) Pos. Component Standard PSU: one PSU Redundant PSU: up to 2 hot-plug PSUs / dummy cover PCI slot 3 / riser module 3 PCI slot 2 / riser module 2 PCI slot 1 / riser module 1...
Page 322: Server Interior
Appendix 16.1.3 Server interior Figure 234: Interior (example 3.5-inch HDDs and standard PSU) Pos. Component Standard PSU: one PSU Front panel module / front VGA (option) / dummy cover Up to 4x 3.5-inch HDDs / dummy modules ODD (option) / dummy cover 4x fan modules Main memory SATA DOM (option)
Page 323 Appendix Figure 235: Interior (example: 2.5-inch HDDs and redundant PSU) Pos. Component Redundant PSU: up to 2 hot-plug PSUs / dummy cover Front panel module / front VGA (option) / dummy cover ODD (option) / dummy cover Up to 8x 2.5-inch HDDs / dummy modules 5x fan modules Main memory SATA DOM (option)
Page 324: Connectors And Indicators
Appendix 16.2 Connectors and indicators 16.2.1 Connectors and indicators on the system board 16.2.1.1 Onboard connectors FRONTPANEL1 PC98 Riser card (x8) USB 3.0 Slot3 PWR1 Battery USB 3.0 USB3.0 FRONT USB 3.0 USB 3.0 Intel C236 COM1 HDD LED Slot2 DIMM2A Riser card (x4) DIMM1A...
Page 325 Appendix Print Description Connector for optional USB Flash Module (UFM) FRONTPANEL2 Front panel connector (front panel on QRL) PSU connector (redundant PSU only) FRONTPANEL1 Front panel connector (front panel module) PWR3 PSU connector for ODD (2.5-inch HDD configuration) PC98 PSU connector (standard PSU only) PWR2 Power connector for HDD backplane PWR1...
Page 326: Onboard Indicators And Controls
Appendix 16.2.1.2 Onboard indicators and controls FRONTPANEL1 PC98 Riser card (x8) USB 3.0 Slot3 PWR1 Battery USB 3.0 USB3.0 FRONT USB 3.0 USB 3.0 Intel C236 COM1 HDD LED Slot2 DIMM2A Riser card (x4) DIMM1A Riser card (x8) DIMM2B Slot1 DIMM1B Standard Intel...
Page 327 Appendix The LEDs have the following meaning: Indicator Meaning A - Identification blue on The server has been highlighted using iRMC web frontend, ServerView Operations Manager or the ID button on the front panel for easy identification. blue flashing The server has been highlighted using IRMC (AVR) when local VGA off for easy identification.
Page 328: Server Front
Appendix Indicator Meaning H - iRMC iRMC S4 inactive green flashing iRMC S4 okay 16.2.2 Server front 16.2.2.1 Indicators on the front panel Figure 238: Indicators on the front panel module Figure 239: Indicators on the front panel on QRL Upgrade and Maintenance Manual RX1330 M3...
Page 329 Appendix Pos. Label Indicator Status Description The server has been highlighted using ServerView Operations indicator, blue on Manager, iRMC web frontend or see also the ID button on the front panel for "iRMC- easy identification. related The server has been highlighted status blue for easy identification using the...
Page 330 Appendix Pos. Label Indicator Status Description – The server is switched off. – The server has been switched on but Power Cycle Delay settings delay it from turning green on on for a specified time. – The server is switched on and Power-on operating normally.
Page 331 Appendix iRMC-related status signals Global error ID indicator Description indicator A remote connection has been established. Local VGA output has blue flashing been disabled during the remote session. An emergency flash of the iRMC blue flashing orange flashing firmware is in progress. For further information please refer to section "Updating or recovering the iRMC"...
Page 332: Indicators On The Accessible Drives/Components
Appendix 16.2.2.2 Indicators on the accessible drives/components Optical drive activity indicator Figure 240: Indicator on the optical drive Pos. Indicator Status Description The optical drive is inactive. Activity indicator green on The storage medium is being accessed. Depending on your system configuration the activity indicator may not be installed.
Page 333 Appendix Indicators on the hot-plug HDD module Figure 241: Indicators on the hot-plug HDD module Pos. Label Indicator Status Description The HDD is inactive. Access indicator green on The HDD is being accessed. No HDD error detected. An HDD error has been detected. Possible causes: –...
Page 334: Server Rear
Appendix 16.2.3 Server rear 16.2.3.1 Connectors on the I/O panel Figure 242: Connector panel No. Description 4x USB 3.0 connectors Serial connector COM1 (can be used as default interface or to communicate with the iRMC S4) Video connector (VGA) Standard LAN connector; this connector is displayed in BIOS Setup Utility and MAC address label as LAN1 Shared LAN connector (for WOL/PXE/iSCSI function);...
Page 335: Indicators On The I/O Panel
Appendix 16.2.3.2 Indicators on the I/O panel ID, CSS and Global Error indicators Figure 243: ID, CSS and Global Error indicators Pos. Label Indicator Status Description The server has been highlighted using ServerView Operations indicator, blue on Manager, iRMC web frontend or see also the ID button on the front panel for "iRMC-...
Page 336 Appendix Pos. Label Indicator Status Description No critical event detected (non component). Prefailure event detected (non Global orange on component). Error indicator, Non CSS component failure see also detected. "iRMC- Possible causes: related – System is out of the specified orange status range...
Page 337 Appendix iRMC-related status signals Global error ID indicator Description indicator A remote connection has been established. Local VGA output has blue flashing been disabled during the remote session. An emergency flash of the iRMC blue flashing orange flashing firmware is in progress. LAN indicators Figure 244: LAN indicators Pos.
Page 338: Indicator On Hot-Plug Psus (Slide-In Unit)
Appendix 16.2.3.3 Indicator on hot-plug PSUs (slide-in unit) Figure 245: Indicator on the hot-plug PSUs Pos. Indicator Status Description green The server is switched off, but mains flashing voltage is present (standby mode). The server is switched on and operating green on properly.
Page 339: Indicator On Fujitsu Battery Unit (Fjbu)
Appendix 16.2.3.4 Indicator on Fujitsu battery unit (FJBU) Figure 246: Indicator on FJBU Pos. Indicator Status Description green The battery unit is charging. flashing green flashing The battery unit is discharging. slowly FJBU status green on The battery unit is fully charged.
Page 340: Onboard Settings
Appendix 16.3 Onboard settings Slot2 DIMM2A Riser card (x4) DIMM1A Riser card (x8) DIMM2B Slot1 DIMM1B Standard Intel i210 SATA5 SATA1-4 Shared Jumper iRMC Intel Indicate SATA6 i210 Front Micro Managem. I2C5 PWR4 Service Jumper Setting Default RCVR PWD-CLR Password Clear Recovery Password Description...
Page 341: Minimum Startup Configuration
Appendix 16.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component. The minimum startup configuration consists of the following components and cables: Component...
Page 342 Appendix CAUTION! Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! Upgrade and Maintenance Manual...

Fujitsu PRIMERGY RX1330 M3 Upgrade And Maintenance Manual

1 Introduction

2 Before You Start

3 Important Information

4 Basic Hardware Procedures

5 Basic Software Procedures

6 Power Supply Unit (PSU)

7 Hard Disk Drive (HDD) / Solid State Drive (SSD)

8 Fans

9 Expansion Cards and Backup Units

10 Main Memory

11 Processor (CPU)

Quick Links

Related Manuals for Fujitsu PRIMERGY RX1330 M3

Summary of Contents for Fujitsu PRIMERGY RX1330 M3