GE VAT200 Quick Start Manual page 40

5-08 (Stop Sel by MFIT) Stop Mode Using MFIT
5-09 (Step Up/Down Fun) Step of Up/Down Function (Hz) 0.00 – 5.00
5-10 (Pulse Inp. Mult.)
5-11 (Ref.Source2)
※ Notes: 1. To switch to Run/Stop with Function 1-01 = 0001.
2. To switch to Forward/Reverse with Function 1-01 = 0001.
3. Preset Speed # 3 is obtained by activating Terms. S3 and S4 simultaneously
6- Jog, and Preset (MFIT) Frequency Setting on Keypad
Function LCD
Code No. Display
6-00 (Keypad Freq)
6-01 (Jog Freq)
6-02 (Preset Speed #1)
6-03 (Preset Speed #2)
6-04 (Preset Speed #3)
6-05 (Preset Speed #4)
6-06 (Preset Speed #5)
6-07 (Preset Speed #6)
6-08 (Preset Speed #7)
7- Analog Input Signal Operation
Function LCD
Code No. Display
7-00 (AIN Gain)
7-01 (AIN Offset)
7-02 (AIN Bias)
7-03 (AIN Slope)
7-04 (AIN Scan Time)
7-05 (AI2 Gain)
Encoder Inpulse Ratio
Select the source of auxiliary
frequency command
Description
Keypad Frequency (Hz)
Jog Frequency (Hz)
Preset Speed # 1 (Hz)
Preset Speed # 2 (Hz)
Preset Speed # 3 (Hz)
Preset Speed # 4 (Hz)
Preset Speed # 5 (Hz)
Preset Speed # 6 (Hz)
Preset Speed # 7 (Hz)
Description
AIN Gain (%)
AIN Bias (%)
AIN Bias Selection
AIN Slope
AIN Signal Verification Scan
Time (AIN, AI2)
(mSec x 2)
AI2 Gain (%)(S6)
0000: When the MFITs are
Programmed for Up/Down
Frequency Control, the Set
Frequency will remain when
the Drive stops. And when the
Drive stops, Up/Down
Function Disabled.
0001: Up/Down is used. The preset
frequency is reset to 0 Hz as
the inverter stops.
0002: When the MFITs are
Programmed for Up/Down
Frequency Control, the Set
Frequency will remain when
the Drive stops. And when the
Drive stops, Up/Down
Function Enabled. *7
0.001 – 9.999
0 - 4
Range/Code
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
0.00 - 650.00
Range/Code
0 - 200
0 - 100
0000: Positive
0001: Negative
0000: Positive
0001: Negative
1 - 100
0 - 200
4-14
Chapter 4 Software Index
0000
0.00
1.000
0
.
Factory
Remarks
Setting
5.00
2.00
5.00
10.00
20.00
30.00
40.00
50.00
60.00
Factory
Remarks
Setting
100
0
0000
0000
50
100
*7
*7
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1