Download  Print this page

GE UltraMax Installation Manual

Connected led driver.
Hide thumbs
   

Advertisement

GE Lighting Solutions
1975 Noble Rd. Cleveland, OH 44112
UltraMax
Only Qualified Electricians Should Perform the Installation of this LED Driver
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005(A).
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This equipment (GED80MCC/Z2P1500) contains the limited module with FCC ID PUU80MCCZ2P15
and ISED ID 10798A-80MCCZ2P15. This equipment complies with FCC CFR 47 Part 2 requirements for
radiation exposure for fixed facility or mobile applications that maintain a distance of 20 cm from a
person's body. This equipment complies with ISED RSS-102 Issue 5 requirements for radiation exposure
limits for an uncontrolled environment that maintain a distance of 20 cm from a person's body.
This radio transmitter ISED ID 10798A-80MCCZ2P15 has been approved by Innovation, Science and
Economic Development Canada to operate with the antenna types listed below, with the maximum
permissible gain indicated. Antenna types not included in this list that have a gain greater than the
maximum gain indicated for any type listed are strictly prohibited for use with this device.
TM
Connected LED Driver Installation Guide
GED80MCC/Z2P1500
BEFORE YOU BEGIN: Please read these instructions
completely and carefully

Advertisement

Table of Contents

   Related Manuals for GE UltraMax

   Summary of Contents for GE UltraMax

  • Page 1 GE Lighting Solutions 1975 Noble Rd. Cleveland, OH 44112 UltraMax Connected LED Driver Installation Guide GED80MCC/Z2P1500 BEFORE YOU BEGIN: Please read these instructions completely and carefully Only Qualified Electricians Should Perform the Installation of this LED Driver This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 2 Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Only the following antennas should be used with this limited module and the antenna should only be installed when the host product is manufactured.
  • Page 3 6. Install the new driver and make sure the new driver is properly grounded to metal fixture per National Electrical Code (NEC). Tighten driver mounting screws seating driver firmly against fixture surface. To insure electrical grounding between driver case and fixture housing mounting screws with star washers are recommended to break (penetrate) the painted surface of the driver mounting foot.

Comments to this Manuals

Symbols: 0
Latest comments: