Mitsubishi Electric FX5 User Manual page 418

Error Error name
code
3628H Axis 8 limit
detection error
3629H Axis 9 limit
detection error
362AH Axis 10 limit
detection error
362BH Axis 11 limit
detection error
362CH Axis 12 limit
detection error
3631H Axis 1 positioning
address error
3632H Axis 2 positioning
address error
3633H Axis 3 positioning
address error
APPX
416
Appendix 3 Error Code
Error details and cause
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
Action
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Start the positioning within specifications.
• Start the positioning within specifications.
• Start the positioning within specifications.
Detailed Diagnostic
information timing
Error location At END
information instruction
and system execution, at
configuration instruction
information execution
Error location At END
information instruction
and system execution, at
configuration instruction
information execution
Error location At END
information instruction
and system execution, at
configuration instruction
information execution
Error location At END
information
instruction
and system execution, at
configuration instruction
information execution
Error location At END
information instruction
and system execution, at
configuration instruction
information
execution
Error location At END
information instruction
and system execution, at
configuration interrupt
information occurrence
Error location At END
information instruction
and system execution, at
configuration interrupt
information occurrence
Error location At END
information instruction
and system execution, at
configuration interrupt
information occurrence