Mitsubishi Electric FX5 User Manual page 414

Error Error name
code
33E2H Program
structure error
33E3H Program
structure error
33E4H Program
structure error
33E5H Program
structure error
33E6H Program
structure error
33E7H Program
structure error
33F1H Program
structure error
33F2H Program
structure error
33F3H Program
structure error
3400H Operation error
3401H Operation error
3402H Operation error
3403H Operation error
3404H Operation error
3405H Operation error
3406H Operation error
3420H Operation error
3500H Operation error
3502H Operation error
3503H Operation error
3504H Operation error
3505H Operation error
3506H Operation error
350AH Operation error
APPX
412
Appendix 3 Error Code
Error details and cause
• An instruction that should start from the
bus line is not connected to the bus line.
• The relationship between FOR and
NEXT instructions is invalid.
• The relationship between MC and MCR
instructions is invalid.
• The relationship between STL and
RETSTL instructions is invalid.
• An instruction or interrupt pointer that
cannot be used in the main routine
program is used.
• The relationship among a global pointer,
interrupt pointer, and return instruction is
invalid.
• The program structure of the ST
language, FB, and functions is invalid.
• The program structure of the ST
language, FB, and functions is invalid.
• More than two STL instructions for the
same S number are programmed.
• A value of 0 was input as a divisor in an
applied instruction.
• Data that cannot be converted was input
in an applied instruction.
• A value of -0, a denormalized number, a
non-number, or ±∞ was input in an
applied instruction.
• An overflow occurred in an applied
instruction.
• A string that is not supported in the
instruction was specified.
• Data that is outside the allowable range
was input in an applied instruction.
• The output result is outside the allowable
device range in an applied instruction.
• A module access device is specified to
both (s) and (d) in a BMOV instruction.
• A value outside the allowable range was
set to the sampling time (TS).
• A value outside the allowable range was
set to the input filter constant (α).
• A value outside the allowable range was
set to the proportional gain (KP).
• A value outside the allowable range was
set to the integral time (TI).
• A value outside the allowable range was
set to the derivative gain (KD).
• A value outside the allowable range was
set to the derivative time (TD).
• The sampling time is lower than the scan
time.
Action
• Rewrite the program file.
• Modify the program so that the mutual
relationship between instructions becomes
correct.
• Modify the program so that the mutual
relationship between instructions becomes
correct.
• Modify the program so that the mutual
relationship between instructions becomes
correct.
• Modify the program so that instruction or
pointer use becomes correct.
• Modify the program so that the mutual
relationship between pointer and return
instruction becomes correct.
• Check the syntax of the ST language, FB,
and functions.
• Check the syntax of the ST language, FB,
and functions.
• Recheck the structure of the step ladder.
• Review the data specified as the divisor in
the applied instruction.
• Review the data specified in the applied
instruction.
• Review the data specified in the applied
instruction.
• Review the data specified in the applied
instruction.
• Review the data specified in the applied
instruction.
• Review the data specified in the applied
instruction.
• Review the data specified in the applied
instruction.
• Review the device specified in the BMOV
instruction.
• Check the contents of the parameters.
• Check the contents of the parameters.
• Check the contents of the parameters.
• Check the contents of the parameters.
• Check the contents of the parameters.
• Check the contents of the parameters.
• The operation is continued in the condition
"sampling time (TS) = cyclic time (scan
time)".
Detailed Diagnostic
information timing
Error location At power-on,
information at RESET
Error location At power-on,
information at RESET
Error location At power-on,
information at RESET
Error location At power-on,
information at RESET
Error location At power-on,
information at RESET
Error location At power-on,
information at RESET
Error location At END
information instruction
execution, at
interrupt
occurrence
Error location At instruction
information execution
Error location At power-on,
information at RESET, at
STOP →
RUN state
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution
Error location At instruction
information execution