Toshiba strata DK8 Installation Instructions Manual page 268

SECTION lOO-816-302
MARCH1993
Forced/Verified Account Code dialing restric-
tions set in Programs 69 and 30 (LEDs 8 and
14). If CO lines are behind CENTREX or PBX,
program the appropriate one-digit or two-digit
CENTREX/PBX trunk access code in front of
the emergency number. Example: If the PBX
trunk access code is 8, then program 8911 in
Program 44A-51 to allow 911 to bypass Forced/
Verified Account Code dial requirements.
NOTES:
1. If CO lines are behind PBX or CENTREX,
program the PBXCENTREXoutside trunk
access code. (See Program 42-O and
42-1 to assign CO lines and access codes
for behind PBXKENTREX operation.)
2. If Verified Account Codes assigned in
Program 69 conflict (duplicate) with
emergency or other type telephone num-
bers set in Program 44A, Program 44A
has priority.
3. Toll Restriction and Direct Inward System
Access (DISA) parameters requirements
are not affected by this program.
Programs 45 - 48-Toll Restriction: All Toll
Restriction program information is provided later
in this chapter.
Programs
50 - 56-Least Cost Routing: All
Least Cost Routing program information is pro-
vided later in this chapter.
Program 60-Station Message Detail Record-
ing (SMDR) Output/Account Code Digit
Length:
SMDR Threshold Time, Item 2-The time
that a call must be in progress before it will
register with SMDR can be set to 1 second
or 10 seconds. The default is 10 seconds.
SMDR Output, Item 3-System output to
an SMDR device can include information for
both incoming and outgoing calls, or only for
outgoing calls. Local and long distance call
data will be sent out.
Forced/Voluntary/Verified Account Code
Digit Length, Item 4-The Account Code
entered at a station can vary in length from
4 - 15 digits. For Forced Account Code use,
a call will not be completed unless the speci-
fied number of digits is entered by a station
user. With Voluntary Account Codes, the
Account Code will not be sent to the SMDR
call record unless the specified number of
digits are dialed. See Program 69 for Veri-
fied Account Codes.
SMDR Printout Options, Item 5-This
option selectively deletes local call data and
allows long distance/toll call data only to be
sent out the SMDR port. The type of long
distance/toll call data that prints out is se-
lected by long distance prefix codes 0, 1 , 00,
or 1 or 0.
Direct Inward System Access (DISA) Se-
curity Code, Item 6-A security code (1 -
15 digits) can be required for incoming DISA
calls to access outgoing CO lines. If the
DISA security code is not set in program-
ming, DISA users can access outgoing CO
lines without dialing a security code. This
code is not required for DISA calls to sta-
tions. The DISA security code can also be
changed from stations enabled in Program
30.
Credit Card Call Digit Length, Item 07-
Station users bypassing Toll Restriction with
the "O+" Credit Card Calling feature (Pro-
gram 43) must dial a predetermined num-
ber of digits including the "O."This predeter-
mined number is established with Item 7 and
can be 1 - 30 digits.Program 69-Verified
Account Codes: Verified Account Codes
may be added, deleted, or changed with
Program 69. The STRATA DK8 allows a
maximum of 100 Verified Account Codes;
the Strata DKl6 allows a maximum of 300.
Each Verified Account Code can be 1 - 15
digits long, but cannot exceed the overall
Account Code length requirement set in
Program 60-4. The following programs and
options should be considered when estab-
lishing Verified Account Codes.
Account Code Digit Length-Program
60-4 sets the digit length that must be dialed
for all Account Codes: Forced (Verified/
Nonverified) and Voluntary (Verified/
Nonverified).
2-18