Toshiba strata DK8 Installation Instructions Manual page 163

program the VM machine to dial the following
sequences (in
Program 10-2,
turn LED 04 ON):
1) To set a MW LED, the VM machine must
dial 6 3 + station number.
2) To cancel a MW LED, the VM machine
must dial 6 4 + station number.
NOTE:
Only dial codes 63 and 64 are set in the VM
device configuration; the VM device will dial
the station numberautomatically to set/cancel
the Message Waiting indication LED.
No Conference
VM-Prevents undesired CO
line three-party connections during VM call
transfers. All VM ports should be set for no
conference
(Program 31,
LED 09).
Privacy Override
Deny-Prevents stations from
overriding (breaking in) in-progress VM calls
(Program 31,
LED 18).
End-to-End
Signaling-Allows VM port
DTMF operation. All VM ports should be set for
end-to-end signaling
(Program 31,
LED 17).
NOTE:
The DK8 QRCU or DK16 K4RCU must be
installed to allow End-to-End Signaling.
VM to VM Call Blocking-Prevents VM auto
attendant calls from forwarding back to VM auto
attendant during supervised transfers
(Program
31, LED 04 ON). This will prevent the problem of
auto attendant to auto attendant looping connec-
tions.
Receive Auto Call Forward ID
Codes-Pro-
vides auto digits from call forwarded stations to
direct callers to stations' mailboxes. All VM ports
should be set to receive auto ID code
(Program
31,
LED 16).
"A" and "D" tones; see Paragraph 7.13.
7.24 Voice Mail Program Checklist.
The follow-
ing items should be verified before programming
voice mail:
1) Set Toshiba VP Maintenance Menu system
parameters to "D" = STRATA DK8 and DK16
INSTALLATION-PERIPHERALS
SECTION 100-816-207
MARCH 1993
(seeToshibaVP /nsta//ationandMaintenance
Manual for other parameter settings).
2) STRATA DK8 and DK16 programs:
Program
92: Initialization clears voice mail
auto dial codes.
Program
03: Verify that the KRCU is pro-
grammed in the Base Unit to allow the VM/
AA to send DTMF tones (does not apply to
DK8).
Program
04: Assigns station numbers to
VM/AA ports (initialized numbers recom-
mended).
Program
05: First digit of special codes 63
and 64 (initialized numbers recommended).
Program 1 O-l
: Set the system for voice first,
and program the VM/AA device to dial the
suffix as "1" after station numbers.
Program 1
O-2: Set LED 04 ON for set/cancel
operation and 06 ON for the VM to detect 80
msec. tones.
Program 13:
If the VM/AA device is the
message center, set the lowest VM port as
the message center.
Program 31:
Turn LEDs 05,09, and 15 - 20
ON for the QSTU, KSTU, PESU, or PSTU
ports that are connected to-the Toshiba VP
VM/AA ports. Do not set these options for
standard telephone, digital telephone, or
electronic telephone station ports. LED 04
should beoff iftheautoattendantonly"BLIND"
transfers; if the AA does "Supervise" or
"Screened" transfers, set LED 04 ON for auto
attendant ports.
NOTE:
A, D, and B tones should be enabled only for
VM/AA devices that respond to these tones.
l
Program
33: Set the QSTU, KSTU, PESU
and PSTU ports that are connected to the
VM/AA ports to a hunting sequence, starting
with the lowest port hunting to the next high-
est port, etc. The last hunt should be to an
attendant.
l
Program
35: LEDs 01 and 02 must be ON for
stations to receive the message indication
(Msg LED flashing) from a VM device.
7-31