About Parameters; Parameter Groups; Chapter 3 Programming And Parameters About Parameters - Allen-Bradley PowerFlex 525 User Manual

Chapter 3 Programming and Parameters

About Parameters

Parameter Groups

Basic Display Output Voltage
DC Bus Voltage
Drive Status
Fault 1 Code
Output Freq b001 Fault 2 Code
Commanded Freq b002
Fault 3 Code
Output Current b003 Process Display
Basic Program Motor NP Hertz
Motor OL Current
Motor NP FLA
Motor NP Poles
Language P030
Motor NP RPM
Motor NP Volts P031 Motor NP Power
Terminal Blocks DigIn TermBlk 08
Opto Out1 Sel
Opto Out1 Level
Opto Out1 LevelF
DigIn TermBlk 02 t062 Opto Out2 Sel
DigIn TermBlk 03 t063
Opto Out2 Level
2-Wire Mode t064
Opto Out2 LevelF
DigIn TermBlk 05 t065 Opto Out Logic
DigIn TermBlk 06 t066
Relay Out1 Sel
DigIn TermBlk 07 t067 Relay Out1 Level
Communications EN Addr Sel
EN IP Addr Cfg 1
EN IP Addr Cfg 2
EN IP Addr Cfg 3
Comm Write Mode C121 EN IP Addr Cfg 4
Cmd Stat Select C122 EN Subnet Cfg 1
RS485 Data Rate C123
EN Subnet Cfg 2
RS485 Node Addr C124 EN Subnet Cfg 3
Comm Loss Action C125
EN Subnet Cfg 4
Comm Loss Time C126 EN Gateway Cfg 1
RS485 Format C127
EN Gateway Cfg 2
58
To configure a drive to operate in a specific way, drive parameters may have to be
set. Three types of parameters exist:
• ENUM
ENUM parameters allow a selection from 2 or more items. Each item is
represented by a number.
• Numeric Parameters
These parameters have a single numerical value (0.1V).
• Bit Parameters
Bit parameters have five individual digits associated with features or
conditions. If the digit is 0, the feature is off or the condition is false. If the
digit is 1, the feature is on or the condition is true.
Some parameters are marked as follows.
= Stop drive before changing this parameter.
= 32 bit parameter. Parameters marked 32 bit will have two parameter numbers ([Step Units x] and
32
[Step Units F x]) when using RS485 communications and programming software. The second parameter
number is shown only in the Parameter Groups and Parameter Cross Reference by Name tables for reference.
For an alphabetical listing of parameters, see
on page 128.
b004 Process Fract
b005 Control Source
b006 Contrl In Status
b007 Dig In Status
b008 Output RPM
b009 Output Speed
b010 Output Power
P032 Voltage Class
P033 Torque Perf Mode
P034 Autotune
P035 Accel Time 1
P036 Decel Time 1
P037 Minimum Freq
t068 Relay Out1 LevelF
t069 Relay 1 On Time
t070 Relay 1 Off Time
t071 Relay Out2 Sel
t072 Relay Out2 Level
t073 Relay Out2 LevelF
t074 Relay 2 On Time
t075 Relay 2 Off Time
t076 EM Brk Off Delay
t077 EM Brk On Delay
C128 EN Gateway Cfg 3
C129 EN Gateway Cfg 4
C130 EN Rate Cfg
C131 EN Comm Flt Actn
C132 EN Idle Flt Actn
C133 EN Flt Cfg Logic
C134 EN Flt Cfg Ref
C135 EN Flt Cfg DL 1
C136 EN Flt Cfg DL 2
C137 EN Flt Cfg DL 3
C138 EN Flt Cfg DL 4
Rockwell Automation Publication 520-UM001A-EN-E - February 2013
Parameter Cross Reference by Name
b011 Power Saved b018
b012 Elapsed Run Time b019
b013 Average Power b020
b014 Elapsed kWh b021
b015 Elapsed MWh b022
b016 Energy Saved b023
b017 Accum kWh Sav b024
P038 Maximum Freq P044
P039 Stop Mode P045
P040 Start Source 1 P046
P041 Speed Reference1 P047
P042 Start Source 2 P048
P043 Speed Reference2 P049
t078 Analog Out Sel t088
t079 Analog Out High t089
t080 Anlg Out Setpt t090
t081 Anlg In 0-10V Lo t091
t082 Anlg In 0-10V Hi t092
t083 10V Bipolar Enbl t093
t084 Anlg In V Loss t094
t085 Anlg In4-20mA Lo t095
t086 Anlg In4-20mA Hi t096
t087 Anlg In mA Loss t097
C139 EN Data In 1 C153
C140 EN Data In 2 C154
C141 EN Data In 3 C155
C143 EN Data In 4 C156
C144 EN Data Out 1 C157
C145 EN Data Out 2 C158
C146 EN Data Out 3 C159
C147 EN Data Out 4 C160
C148 Opt Data In 1 C161
C149 Opt Data In 2 C162
C150 Opt Data In 3 C163
Accum Cost Sav b025
Accum CO2 Sav b026
Drive Temp b027
Control Temp b028
Control SW Ver b029
Start Source 3 P050
Speed Reference3 P051
Average kWh Cost P052
Reset To Defalts P053
Anlg Loss Delay t098
Analog In Filter t099
Sleep-Wake Sel t100
Sleep Level t101
Sleep Time t102
Wake Level t103
Wake Time t104
Safety Open En t105
Opt Data In 4 C164
Opt Data Out 1 C165
Opt Data Out 2 C166
Opt Data Out 3 C167
Opt Data Out 4 C168
MultiDrv Sel C169
Drv 1 Addr C171
Drv 2 Addr C172
Drv 3 Addr C173
Drv 4 Addr C174
DSI I/O Cfg C175