Mitsubishi Electric melsec q00ujcpu User Manual page 479

Number Name
XCALL instruction
SM734 execution condition
designation
SFC comment readout
SM735 instruction in
execution flag
MSG instruction
SM738
reception flag
Scaling instruction
SM750
search method setting
PID bumpless
processing
SM774
(for complete
derivative)
Selection of refresh
processing during
SM775
COM/CCOM
instruction execution
Enable/disable local
SM776
device at CALL
Enable/disable local
SM777 device in interrupt
program
PID bumpless
SM794 processing(for
incomplete derivative)
*1: The module whose first 5 digits of serial No. is "06082" or later.
*2: The module whose first 5 digits of serial No. is "07012" or later.
*3: The module whose first 5 digits of serial No. is "07032" or later.
*4: This applies to the CPU module of function version B or later.
*5: The module whose first 5 digits of serial No. is "04012" or later.
*6: The module whose first 5 digits of serial No. is "05032" or later.
*8: The relevant modules are as follows:
• The Universal model QCPU whose serial number (first five digits) is "10102" or later.
• Q00UJCPU, Q00UCPU, Q01UCPU
*9: The Universal model QCPU except the Q00UJCPU.
12 - 13
Table12.8 Special relay
Meaning
OFF : Not executed by
• During OFF, XCALL instructions will not be executed
execution condition
even if execution condition is risen.
risen
• During ON, XCALL instructions will be executed
ON : Executed by execution
when execution condition is risen.
condition risen
OFF : SFC comment readout
instruction is • Turns on the instructions, (S(P).SFCSCOMR) to
inactivated. read the SFC step comments and (S(P).
ON : SFC comment readout SFCTCOMR) to read the SFC transition condition
instruction is comments.
activating.
OFF : Instruction not
executed • Goes ON when MSG instruction is executed
ON : Instruction execution
OFF : Search next Determines a search method when the scaling
ON : 2-part search instruction is executed.
OFF : Matched • Specifies whether to match the set value (SV) with
ON : Not matched the process value (PV) or not in the manual mode.
• Select whether link refresh processing will be
OFF : Performs link refresh
performed or not when only communication with the
ON : Performs no link
CPU module is made at the execution of the COM
refresh
instruction.
OFF : Performs refresh
processes other than • Select whether to perform refresh processes other
an I/O refresh than an I/O refresh set by SD778 when the COM or
ON : Performs refresh set CCOM instruction is executed.
by SD778
• Set whether the local device of the subroutine
OFF : Local device disabled
program called at execution of the CALL instruction
ON : Local device enabled
is valid or invalid.
OFF : Local device disabled • Set whether the local device at execution of the
ON : Local device enabled interrupt program is valid or invalid.
OFF : Matched • Specifies whether to match the set value (SV) with
ON : Not matched the process value (PV) or not in the manual mode.
Explanation
S (status change)
Corres-
Set by ponding Corresponding
ACPU
(When Set)
M9
U New
New
QnPRH
S (Instruction
New
execution)
U New
Q00J/Q00/Q01
U New
Q00J/Q00/Q01
U New
Q00J/Q00/Q01
U New
U New
U New
Q00J/Q00/Q01
U New
CPU
*1
Qn(H)
*2
Qn(H)
*3
QnPH
*3
Qn(H)
QnPRH
*8
QnU
*4
Qn(H)
QnPRH
QnU
Qn(H)
QnPH
*4
*5
Qn(H)
*3
QnPH
QnPRH
QnU
Qn(H)
QnPH
QnPRH
*9
QnU
*4
*6
Qn(H)
QnPRH
QnU