Control Command - Icom IC-910H Instruction Manual

Command Sub command
Send frequency data for trans-
00 —
ceive.
Same as
01 Send mode data for trans-
command 06
ceive.
02 —
Read band edge frequencies.
03 —
Read operating frequency data.
04 —
Read operating mode data.
05 —
Set operating frequency.
00
01 Set LSB.
06
03 Set USB.
04 Set CW.
Set FM.
—
Select VFO mode.
00
01 Select VFO A.
07
A0 Select VFO B.
B0 Equalize VFO A and VFO B.
D0 Switch VFO A and VFO B.
D1 Select MAIN VFO.
Select SUB VFO.
—
Select memory mode.
01–0106*
Select memory channel.
08
*1A=0100
2A=0102
3A=0104
Call=0106
09 —
Memory write.
0A —
Transfer memory contents to
VFO.
0B —
Memory clear.
0C —
Read duplex offset frequency.
0D —
Set duplex offset frequency.
00
01 Cancel scan.
0E
D0 Start scan.
D3 Set scan resume OFF.
Set scan resume ON.
00
01 Turn the split function OFF.
0F 10 Turn the split function ON.
11 Set simplex operation.
12 Set DUP– operation.
Set DUP+ operation.
00
01 Set 1 Hz tuning step.
02 Set 10 Hz tuning step.
03 Set 50 Hz tuning step.
04 Set 100 Hz tuning step.
10 05 Set 1 kHz tuning step.
06 Set 5 kHz tuning step.
07
Set 6.25 kHz tuning step.
08 Set 10 kHz tuning step.
09 Set 12.5 kHz tuning step.
10 Set 20 kHz tuning step.
11 Set 25 kHz tuning step.
Set 100 kHz tuning step.
00
11
10, 20, 30 Turn attenuator OFF.
Turn attenuator ON.
Description
1b=0101
2b=0103
3b=0105
From The N3UJJ.COM Document Library From The N3UJJ.COM Document Library

CONTROL COMMAND

Command Sub command
00 Announce all S-meter levels,
13 displayed
01 mode.
02 Announce displayed frequency.
Announce operating mode.
01
[AF] level setting
02
128=center; 255=max. CW)
[RF GAIN] level setting
03
(0=max. CCW; 255=max. CW)
[SQL] level setting
04
CCW; 255=max. CW)
[IF SHIFT] level setting
06
CCW; 128=center; 255=max. CW)
Set noise reduction level
14 09
(0=0%; 255=100%)
Set CW pitch
0A
255=900 Hz)
[RF PWR] level setting
0B
CCW; 128=center; 255=max. CW)
[MIC GAIN] level setting
0C
CCW; 128=center; 255=max. CW)
Key speed setting
0E
255=60 wpm)
Set mic. compressor level
0F
(0=0%; 255=100%)
Set break-in delay
255=13.0 sec.)
01
15 Read squelch condition
02
or closed)
Read S-meter level.
02
12 Set pre-amp
22 Set AGC
40 Set noise blanker
+level data Set noise reduction level
41
(0=OFF; 1–15=ON)
Set auto notch filter
16 42
(0=OFF; 1=ON)
Set subaudible tone
43
(0=OFF; 1=ON)
44 Set tone squelch
Set mic. compressor
46
(0=OFF; 1=ON)
47 Set VOX
4A Set break-in
Set AFC
19 00
Read the transceiver ID.
00
01 Read/write memory channel.
02 Set satellite memory.
+level data Set VOX gain level
03
(0=0%; 255=100%)
+level data Set VOX delay
04
(0=0 sec.; 20=2.0 sec.)
1A +level data Set anti-VOX
05
(0=0%; 255=100%)
+level data Attenuation level setting
06
(0=0%; 255=100%)
07 Set RIT
Set satellite mode
08
(0=OFF; 1=ON)
Set simple bandscope
13
Description
frequency and
(0=max. CCW;
.
.
(0=max.
.
(0=max.
.
.
(0=300 Hz;
.
(0=max.
.
(0=max.
.
(0=6 wpm;
.
.
(0=2.0 sec;
.
(open
.
.
(0=OFF; 1=ON)
.
(0=Slow; 1=Fast)
.
(0=OFF; 1=ON)
.
.
.
.
(0=OFF; 1=ON)
.
.
(0=OFF; 1=ON)
.
(0=OFF; 1=ON)
.
(0=OFF; 1=ON)
.
.
.
.
.
(0=OFF; 1=ON; 2=Sub dial)
.
79