Default Settings For Copying - Kyocera TASKalfa 620 Service Manual

Printing from unregistered sources (printer)
Authorizes or prohibits printing from computers with
printer drivers that do not support job accounting.
This setting is displayed only if Printer Job Accounting
is [On].
1. Press [Job Accntg Def. Set.].
2. Select [Others Mgt. Reg. (print)] and press [Change
#].
3. Select [On] or [Off].
4. Press [Close].
Copy/Printer output management
Select whether copying and printing are managed
together or separately.
1. Press [Job Accntg Def. Set.].
2. Select [Copy/Printer output mgt] and press
[Change #].
3. Select [All] or [Split].
4. Press [Close].
Scanner job accounting
Activates or deactivates job accounting when the
copier is used for scanning.
This setting is displayed only if the copier is equipped
with the optional scanner kit.
1. Press [Job Accntg Def. Set.].
2. Select [Scanner Job Accounting] and press
[Change #].
3. Select [On] or [Off].
4. Press [Close].
Response to unauthorized requests
Sets the actions when users attempt to copy in excess
of the specified copy limitation.
1. Press [Job Accntg Def. Set.].
2. Select [Apply limit] and press [Change #].
3. Press [Stop job immediately], [Stop after job done]
or [Alert Only].
4. Press [Close].
Default of copy limitation
Sets the default of copy limitation when registering a
new department.
1. Press [Job Accntg Def. Set.].
2. Select [Def. Val. of coun. Limit] and press [Change
#].
3. Enter the number of pages from 1 to 999,999 using
the numeric keys.
4. Press [Close].
Total count by size, 1-5
Registers specific paper sizes and types of paper to
check the copy count.
1. Press [Job Accntg Def. Set.].
2. Select [Total size 1-5] and press [Change #].
3. Press [On].
4. Press [Select size].
5. Select a paper size and press [Close].
6. To specify a paper type, press [Select Media Type].
7. Select the media type and press [Close].
8. Press [Close].

(3) Default settings for copying

Density mode
Exposure mode changes the default for how the copier
adjust how dark or light copying is made.
1. Select [Density Mode] using the cursor up/down
keys and press [Change #].
2. Select [Manual] or [Auto].
Density steps
Changes the number of intermediate steps for manual
adjustment of exposure.
1. Select [Density Steps] using the cursor up/down
keys and press [Change #].
2. Select [1 step] or [0.5 step].
Original image
Sets the default original quality.
1. Select [Original Image] using the cursor up/down
keys and press [Change #].
2. Select [Text+Photo], [Text], or [Photo].
EcoPrint
Selects whether to select EcoPrint on or off.
1. Select [EcoPrint] using the cursor up/down keys
and press [Change #].
2. Select [On] or [Off].
Adjusting background intensity
If the background on copies appears too dark, you can
lighten it.
1. Select [Background Density Adj] using the cursor
up/down keys and press [Change #].
2. Press [Lighter] or [Darker] to adjust the intensity.
Setting range: -2 to +2
Adjusting thin lines
Depending on the using environment, paper or original,
drag marks may appear around horizontal thin lines in
some cases. To eliminate these marks, use the [Thin-
ner] setting in this option.
1. Select [Thin Line adjustment] using the cursor up/
down keys and press [Change #].
2. Press [Thinner] or [Thicker] to adjust the line thick-
ness (1 to 5).
Correcting fine black line
Configures the copier to make them less noticeable if
the copied image has black streaks (dirty streaks not
present on the original).
1. Select [Correcting Black Line] using the cursor up/
down keys and press [Change #].
2. Select [Off], [On(Low)] or [On(High)].
Paper selection
Sets whether the copy paper is automatically selected
according to the size of the original document or the
copy paper in the default cassette is forcibly selected.
1. Select [Paper Selection] using the cursor up/down
keys and press [Change #].
2. Select [APS(automatic paper selection] or [Default
cassette].
2KN/2KP
1-3-99