Honeywell GX-Series Installation And Setup Manual page 197

KEYPAD TEXT
–HIGH RES Zone changing from High Resistance to Normal Closed (1300 to 1200 Ohm)
Eng. Log only
ILL -CODE Illegal code entry
+INST SET Instant set of system or group
INTRUDER Intruder zone activated (opened)
INT DELAY Intruder delay zone activated (opened)
INVALD CD Invalid Code entered
JAM DELAY RF jam signal sent to panel
KEYSWITCH Keyswitch zone activated (opened)
KSW CANCL Keyswitch Cancels alarm activation (system or Group(s) still Set).
KSW P/SET Keyswitch part sets the system or group(s)
KSW RESET Keyswitch resets the system or group(s)
KSW SET Keyswitch full sets the system or group(s)
KSW UNSET Keyswitch unsets (disarms) the systems or group(s)
LATE SET Late Set of the system or group(s)
LEGAL CD Legal code entered
LF RESET Line Fail Reset has occured
LID TAMP Lid Tamper alarm
+LINE FAIL Comms Module Line fail has occured or a Line Fail zone activated (opened)
–LINE FAIL Comms Module Line fail has finished or a Line Fail zone de-activated (closed)
+LINK Link zone activated (opened)
–LINK Link zone de-activated (closed)
LOC WRITE Diagnostics local write event
+LOCKTIMER Lockout timer activated.
–LOCKTIMER Lockout timer de-activated.
+LOG Log zone activated (opened).
–LOG Log zone de-activated (closed).
LOG 90% Event log 90% full
LOG DELAY Log Delay zone has been activated (opened) for longer than the Delay Alarm
time.
+LOW RES Zone changing to low resistance (900 to 800 Ohm).
–LOW RES Zone changing from Low Resistance to Normal Closed (800 to 900 Ohm).
+LOW VOLTS Voltage of AUX outputs has dropped below 10V.
+MASK Mask zone activated (opened).
–MASK Mask zone de-activated (closed).
MASKED Zone masked. Detector has activated its masking output.
MAX ALARM MAX alarm — door forced.
MAX TAMP MAX Tamper
MEM RESET Memory Reset (Restart) to factory default settings (Cold Start).
+MISSING Module Missing its AB (RS485) communications.
–MISSING Module that was Missing now has its AB (RS485) communications re-
established.
MOD CODES Modify Codes menu (Menu Option 42) has been accessed.
MOD REM Remote Servicing menu (Menu Option 47) has been accessed.
MOD SUMMR Modify Summer menu (Menu Option 43) has been accessed.
MOD T/D Modify Time/Date menu (Menu Option 42) has been accessed.
MOD TMRS Modify Timers Control menu (Menu Option 45) has been accessed.
NEW T/D New Time/Date after modification.
OMIT ATM1 Omit all ATM1 zones.
OMIT ATM2 Omit all ATM2 zones.
OMIT ATM3 Omit all ATM3 zones.
OMIT ATM4 Omit all ATM4 zones.
OMIT VIBS Mass omit of vibration zones.
OMIT ZONE Omit zones menu (menu option 0 in Quick Menu or menu option 11 in Full Menu
has been accessed.
OMITTED Zone has been omitted
OVERRIDE Event has been overridden to set the system
OVWR SITE Remote overwrite of the site has occured via Remote Servicing or RS232
module
P.AUDIBLE PA Audible zone activated (opened).
GX-Series Control Panel Installation and Setup Guide
DESCRIPTION
D-3
TRIGGER
EVENT
15. Trouble M
16. Log Zone NM
None NM
2. Intruder M
18. Zone restoral
None M
None NM
None M
None NM
11. Reset/Cancel NM
10. Setting M
None NM
10. Setting M
10. Setting M
10. Setting NM
16. Log Zone NM
20. Fault NM
9. Tamper M
12. M
Modules/Comms
20. Fault
12. M
Modules/Comms
20. Fault
16. Log Zone NM
16. Log Zone NM
None M
None NM
None NM
16. Log NM
16. Log NM
Always TR NM
16. Log NM
15. Trouble M
15. Trouble M
13. Elec Status M
15. Trouble
4. Security M
4. Security M
18. Zone restoral
15. Trouble M
20. Fault
4. Security M
17. Max Tag
9. Tamper M
13. Elec Status NM
9. Tamper M
9. Tamper M
18. Zone restoral
14. Menu Access M
14. Menu Access NM
14. Menu Access NM
14. Menu Access M
14. Menu Access NM
Always TR M
8. Omit M
8. Omit M
8. Omit M
8. Omit M
8. Omit M
None N
8. Omit M
None M
None M
None NM