Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 24.0
23.4
New Zealand Telepermit Notes
•
The grant of a telepermit for a device does not
indicate Telecom acceptance of responsibility for
the correct operation of the device under all
operating conditions.
•
This equipment shall not be used in any manner
that could constitute a nuisance to other Telecom
customers.
•
Disconnect this equipment immediately if it
becomes physically damaged and arrange for its
disposal or repair.
•
The transmit level from this device is set at a
fixed level, so there may be circumstances where
the performance is less than optimal. Before
reporting such occurrences as faults, please check
the line with a standard telepermitted telephone
and do not report a fault if the telephone
performance is satisfactory.
•
This device is equipped with pulse dialing while
the Telecom standard is DTMF tone dialing.
There is no guarantee that Telecom lines will
always continue to support pulse dialing.
Use of dialing, when this equipment is connected
to the same line as other equipment, may give
rise to bell tinkle or noise and may also cause a
false answer condition. If problems such as this
occur, the user should not contact the Telecom
Faults Service.
•
This equipment is set up to carry out test calls at
pre-determined times. These test calls interrupt
other calls that might be set up on the line at the
same time. Discuss the timing set for these test
calls with the installer.
The timing set for test calls from this equipment
may be subject to drift. If this proves to be
inconvenient and your calls are interrupted,
discuss the problem of timing with the
equipment installer. Do not report the matter as
a fault to Telecom Faults Service.
•
This equipment shall not be set up to make
automatic calls to the Telecom 111 Emergency
Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to
other Telecom customers.
•
In the event of any problem with this device,
disconnect the system battery, AC MAINS
supply, and the telephone line. The user must
arrange with the supplier of the device for the
necessary repairs.
If the matter is reported to Telecom as a wiring
fault and the fault is proven to be due to this
product, a call-out charge will be incurred.
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
Programming Sheets
24.0 Programming Sheets
Primary Telephone Number for Receiver 1
Location
Default
Secondary Telephone Number for Receiver 1
Location
Default
Handshake Tone for Receiver 1
Location
1
HI LO handshake (Contact ID)
2
1400 Hz (Ademco TX at 1900 Hz)
3
2300 Hz (Low Speed Sescoa)
4
No handshake
5
Pager
Transmission Format for Receiver 1
Location
1
Contact ID
2
4 + 2 express
3
FSK 300 baud
4
Domestic
5
Basic pager
6
Reserved
7
Reserved
8
Reserved
Subscriber ID Number For Receiver 1
Location
Default
Primary Telephone Number for Receiver 2
Location
Default
Secondary Telephone Number for Receiver 2
Location
Default
Handshake Tone for Receiver 2
Location
1
HI LO handshake (Contact ID)
2
1400 Hz (Ademco TX at 1900 Hz)
3
2300 Hz (low speed Sescoa)
4
No handshake
5
Pager
Transmission Format for Receiver 2
Location
1
Contact ID
2
4 + 2 express
3
FSK 300 baud
4
Domestic
5
Basic pager
6
Reserved
7
Reserved
8
Reserved
000 to 015
Refer to page 49
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
016 to 031
Refer to page 50
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
032
Refer to page 50
033
Refer to page 50
034 to 039
Refer to page 50
040 to 055
Refer to page 49
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
056 to 071
Refer to page 50
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
072
Refer to page 50
073
Refer to page 50
EN | 98
0 0 0 0 0 0
Advertisement
Table of Contents
