Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 11.0
11.10 Ring Count
175
Location
8
Default
0
Panel does not answer
1 to 13
Number of rings until panel answers
14
Answering machine bypass 2
15
Answering machine bypass 1
This location sets the number of rings before the
control panel answers an incoming call. Set this
count to an acceptable level, noting that one ring is
"Ring, Ring – Ring, Ring" and that a Ring Count of
10 represents approximately 60 sec. This location has
an effect only if Remote Arming, Remote
Upload/Download using Alarm Link, or both are
enabled. Programming this location to 0 prevents the
control panel from answering incoming calls
regardless of any other programmed options.
Answering Machine Bypass
Answering Machine Bypass allows a connection with
the control panel for Remote Arming or
Upload/Download when an answering machine or
facsimile machine is on the same telephone line.
Answering Machine Bypass has two different
methods. Program a 14 to use the secondary method
only when there is a large amount of traffic on the
line (at a home office, for example). This method
reduces the chance of the control panel incorrectly
answering an incoming call.
Programming the Ring Count to 15 enables
Answering Machine Bypass in the primary mode.
When calling the control panel, allow the telephone
to ring no more than four rings and then hang up. If
you call again within 45 sec, the control panel
answers the call on the first ring and the connection
is established. This prevents the answering machine
or facsimile machine from answering the call. To
enable Answering Machine Bypass only when the
system is armed, select Option 2 in Location 177
(refer to Section 12.1 Dialer Options 1 on page 53).
Program the Ring Count to 14 to enable Answering
Machine Bypass in the secondary mode. In this case,
call the control panel and allow the phone to ring no
more than two rings and hang up. Wait a minimum
of 8 sec and call the control panel again. The control
panel answers on the first ring. If you do not wait the
8 sec, the control panel does not answer the call. To
enable Answering Machine Bypass only when the
system is armed, select Option 2 in Location 177
(refer to Section 12.1 Dialer Options 1 on page 53).
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
Dialer Information
Set the Ring Count for the answering
machine or facsimile machine to a value
greater than two rings. Four to six rings is
preferred.
Program a 0 into this location to disable
the control panel from answering an
incoming call.
11.11 Telephone Line Fault Options
176
Location
0
Default
1
Display FAULT indicator when telephone line fails
2
Sound alarm when system is armed
4
Sound alarm when system is disarmed
8
Reserved
This location has three options. You can select any
combination of these options by programming a
single value. Calculate this value by adding the
option bit numbers together. Refer to Section 2.3
Programming Option Bits on page 11 for more
information.
The control panel monitors the telephone line. If the
telephone line is cut or disconnected for longer than
40 sec, the control panel lights the FAULT indicator
on the codepad. The FAULT indicator is
extinguished after the telephone line is restored for
longer than 40 sec.
Options 2 and 4 do not operate unless
you also enable Option 1.
1 – Display FAULT Indicator When the Telephone
Line Fails
When this option is selected, the FAULT indicator
flashes and the codepad buzzer beeps once per min if
the control panel detects that the telephone line is
disconnected. Refer to Section 4.13 Fault Descriptions
on page 24 for more information.
2 – Sound Alarm When System Is Armed
You must also select Option 1 to use this option. If
the control panel detects that the telephone line is
disconnected when the system is armed, the horn
speaker, bell, and strobe outputs are activated.
4 – Sound Alarm when System Is Disarmed
You must also select Option 1 to use this option. If
the control panel detects that the telephone line is
disconnected when the system is disarmed, the horn
speaker, bell, and strobe outputs are activated.
If you program 7 in this location, the horn
speaker, bell, strobe, and EDMSAT
outputs are all activated when the system
is armed or disarmed.
EN | 52
Advertisement
Table of Contents
