Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 2.0
1. Press [0 #].
You are positioned at Location 000 (the Primary
Telephone Number for Receiver 1).
2. To program the number, press:
[10 * 2 * 13 * 9 * 6 * 7 * 2 * 1 * 10 * 5 * 5 * 0*]
Example (Auto Step Disabled)
To enter the Primary Telephone Number 02 (pause)
9672 1055 when auto step is disabled:
1. Press [0 #].
You are positioned at Location 000 (the Primary
Telephone Number for Receiver 1).
2. To program the number, press:
[10 * # 2 * # 13 * # 9 * # 6 * # 7 * # 2 * # 1 * #
10 * # 5 * # 5 * # 0 *]
2.4.9
Command 999 – Display the Panel
Type or Software Version Number
When using the remote codepad, this command
shows the version of the control panel. Because two
different control panels use the same printed circuit
board (PCB), it is difficult to determine the control
panel the PCB is set to.
The codepad displays 4, 6, or 8 to indicate the
control panel software.
Table 6:
Control Panel Type
Indicator
Control Panel Type
8
ICP-CC408
To show the control panel type or software
version number:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound and the remote codepad
displays the data programmed in Location 000.
If you are using the remote codepad, the STAY
and AWAY indicators flash to indicate you
entered Installer's Programming Mode.
2. Enter [9 9 9 #].
Two beeps sound.
If you are using the remote codepad, the
codepad displays a zone indicator corresponding
to the control panel type. Refer to Table 6 for
more information.
3. Press [#] to exit from this command and return
to the Installer's Programming Mode.
4. Enter [9 6 0 #] to exit from Installer's
Programming Mode.
Two sound and the system returns to the
disarmed state.
If you are using the remote codepad, the STAY
and AWAY indicators are extinguished to
indicate the system is disarmed.
2.5
Disable Factory Defaults
Location
900
Default
0
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
Programming
This feature prevents the control panel from being
manually defaulted by the default button and
prevents the use of a programming key to
automatically download to the control panel when
the system is disarmed.
Program 0 into this location to allow defaulting of the
control panel. If you program 15, defaulting of the
control panel is not permitted and the Installer Code
must be used for additional programming of the
control panel.
If the Installer Code is unknown, you must return the
control panel to your Bosch Distributor for exchange.
A nominal fee applies for this service.
The use of this feature is not
recommended.
If you are required to disable the ability to default the
control panel, a special procedure eliminates the
possibility of accidentally setting this option. You
must hold down the default button on the printed
circuit board (PCB) when programming this location.
To prevent manual defaulting of the control
panel:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound and the remote codepad
displays the data programmed in Location 000.
If you are using the remote codepad, the STAY
and AWAY indicators flash to indicate you
entered Installer's Programming Mode.
2. Enter [9 0 0 #] to move to Location 900.
3. Press and hold the default button.
The default button is located at the top of the
PCB next to the PROGRAMMING KEY socket.
4. Enter [1 5 *] to program 15 into Location 900.
5. Release the default button.
6. Enter [9 6 0 #] to exit from Installer's
Programming Mode.
Two beeps sound and the system returns to the
disarmed state.
If you are using a remote codepad, the STAY
and AWAY indicators are extinguished to
indicate the system is disarmed.
If Location 900 is not programmed as 15, do one of
the procedures below to successfully default the
control panel to the factory settings.
To default the control panel using the Installer
Code:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound. The STAY and AWAY
indicators begin to flash to indicate you entered
Installer's Programming Mode.
EN | 14
Advertisement
Table of Contents
