Table of Contents
Advertisement
ICP-CC408 | Installation Guide | Index
Subscriber ID Number For Receiver 1 .............50
Telco Arming Sequence ......................................51
Telephone Line Fault Options...............52, 78, 82
Disarming
Automatic ..............................................................77
Both Areas At Same Time ........................... 33, 39
From AWAY Mode .............................................20
Domestic Dialling
Command 965 ......................................................13
Disable ............................................................ 32, 37
Format....................................................................43
Function .................................................................43
Duress Alarm ............................................................22
EDM Smart Watch ..................................................78
EDMSAT...................................................................69
Entry Guard Timer For STAY Mode ............ 20, 21
Exit Installer's Programming Mode.......................12
Fault
AC Mains Failure .................................................25
Communication Failure.......................................24
Low Battery ...........................................................24
Sensor Watch ........................................................24
Fault Analysis Mode ................................................23
Exit .........................................................................40
FAULT Indicator ........................................16, 18, 19
Features
Solution 404 ............................................................8
Fire Alarm .................................................................22
Forced Arming................................................... 20, 21
Handover...................................................................59
Hold Down Function
Arm In STAY Mode 1.........................................39
Arm In STAY Mode 2.........................................39
Bell Test .................................................................40
Initiate Modem Call.............................................40
Reset Latching Outputs .......................................40
Send Test Report..................................................41
Strobe Test.............................................................40
Turning Day Alarm On/Off ...............................40
Installer Code ...........................................................54
Installer Code Function
Change Telco Arm/Disarm Sequence ....... 30, 36
Setting STAY Mode 2 Zones ....................... 31, 37
Telephone Monitor Mode...................................32
Installer's Programming Commands
959 - Test Programming Key..............................11
960 - Exit Installer's Programming Mode .........12
961 - Reset Control Panel Back To Factory
Default................................................................12
965 - Set Up Domestic Dialling..........................13
966 - Automatic Stepping Of Locations ............13
999 - Display Panel Type/Software Version
Number ..............................................................14
Introduction ................................................................8
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
Invalid Code .............................................................79
Isolate In STAY Mode 1.........................................62
Isolating Allowed .....................................................62
Isolating Zones..........................................................23
Latching Outputs
Resetting ................................................................40
Lockout Dialler.........................................................61
Lockout Siren............................................................61
Low Battery...............................................................24
MAINS Indicator ........................................ 16, 17, 18
Master Code Function
Arm/Disarm Both Areas At Same Time.... 33, 39
Changing & Deleting User Codes......................33
Setting Date and Time.........................................38
Turning Outputs ON/OFF .................................38
Walk Test Mode ...................................................38
Master Partitioned Codepad
Area Display Indicators.......................................19
Area On/Off Indicators.......................................18
Zone Indicators.....................................................18
Medical Alarm..........................................................22
Modem Call ..............................................................40
New Zealand Telepermit Notes .............................98
Night Arm Station....................................................88
Off Indicator .............................................................18
On Indicator .............................................................18
Option Bits ................................11, 42, 53, 56, 60, 62
Optional Equipment
2-hannel Radio Interface .....................................87
8 Zone LED Codepad .........................................87
Night Arm Station ................................................88
Programming Key ................................................87
TF008 Plug Pack...................................................88
Output Event Type
AC Fail...................................................................70
AC Mains 60 Hz or 50 Hz..................................72
Alarm When In AWAY Mode...........................71
Alarm When In STAY Mode.............................71
Any Areas Armed ................................................73
Any Areas Disarmed............................................73
Area 1 Codepad Data Terminal.........................73
Area 1 Has Zone Unsealed .................................73
Area 1 In Alarm ...................................................73
Area 1 Is Armed...................................................73
Area 1 Is Disarmed ..............................................73
Area 2 Codepad Data Terminal.........................73
Area 2 Has Zone Unsealed .................................73
Area 2 In Alarm ...................................................73
Area 2 Is Armed...................................................73
Area 2 Is Disarmed ..............................................73
Armed In AWAY Mode .....................................69
Armed In STAY Mode .......................................69
Auto Arm Pre-Alert Time ...................................69
AUX Power Supply Fail......................................70
EN | 108
Advertisement
Table of Contents
