Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 6.0
You can suspend the Telco disarming sequence at
any time. To disable the Telco disarming
sequence:
Enter your Master Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
To program the Telco arming sequence – easy
call forward (immediate on):
1. Enter your Master Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1][AWAY] button to change the Telco
arming sequence. Three beeps sound.
If a call forwarding sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 37 on page 36 for the indicators and
their meanings.
If no call forward sequence is programmed, an
additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the call forward sequence is
displayed.
3. Press [STAY][1 2 1] and enter the phone number
to which you want calls from the control panel
diverted.
4. Press [STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
Example
If you want to automatically divert all incoming calls
to another telephone number (for example, 9672
1777) when the system is armed in AWAY Mode,
enter:
[2 5 8 0 3][AWAY][1][AWAY][STAY]
[1 2 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the Telco arming sequence at any
time. To disable the Telco arming sequence:
Enter your Master Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy
call forward (immediate off):
1. Enter your Master Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [2][AWAY] to change the Telco disarming
sequence.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 37 on page 36 for the indicators and
their meanings.
If no Telco disarming sequence is programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the sequence is displayed.
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
System Functions
3. Press [STAY][2 2 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the Telco disarming sequence at
any time. To disable the Telco disarming
sequence:
Enter your Master Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
6.2.6
Setting STAY Mode 2 Zones
This function allows the Master Code holder to select
the zones that are isolated automatically when the
system is armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and
hold [0] until two beeps sound. Refer to Section 6.4.3
on page 39 or Section 4.5 Arming the System in STAY
Mode 2 on page 21 for more information.
To set STAY Mode 2 zones:
1. Enter your Master Code and press [4][AWAY].
Three beeps sound and the STAY indicator
flashes.
2. Enter the number of the zone you want to isolate
automatically and press [STAY].
The corresponding zone indicator flashes.
3. Repeat Step 2 to select each zone.
As each zone is selected to be isolated,
the corresponding zone indicator flashes.
If you make a mistake, enter the incorrect
zone number and press [STAY]. This zone
is no longer selected to be isolated and
the zone indicator is extinguished.
This function does not work on a
partitioned ICP-CC408 Control Panel.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the zones you selected and the
STAY indicator are extinguished.
Example
If you want to select zones 2, 5, and 6, enter:
[2 5 8 0 4][AWAY][2][STAY][5][STAY][6][STAY]
[AWAY]
You can disable all zones selected to be automatically
isolated for STAY Mode 2 at any time. To disable
STAY Mode 2 zones:
Enter your Master Code and press [4][AWAY]
[AWAY].
EN | 37
Advertisement
Table of Contents
