Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 18.0
8 – STAY Indicator To Display Day Alarm Status
If this option is selected, the STAY indicator flashes
once every 3 sec when Day Alarm is enabled.
Specify Day Alarm zones in Location 265 (refer to
Section 14.1 Day Alarm Information on page 56 ).
You can turn Day Alarm on and off by holding
down [4] for 2 sec. Three beeps indicate Day Alarm
is turned on and two beeps indicate Day Alarm is
turned off. Refer to Section 14.1.3 Day Alarm Operation
on page 56 or more information.
18.6
Consumer Options 2
429
Location
1
Codepad display extinguishes after 60 sec
2
Single button arming allowed (AWAY/STAY Modes
1 and 2)
4
Single button disarming allowed (STAY Modes 1
and 2)
8
Alarm memory reset on disarm
1 – Codepad Display Extinguish after 60 Sec
If this option is selected, all indicators on the remote
codepad display are extinguished if a button is not
pressed for 60 sec. The indicators lights again when
there is an alarm (except a silent alarm), when a
button is pressed on the codepad, when the AC
MAINS fail beeps, or if the Entry Timer is activated.
2 – Single Button Arming Allowed
If this option is selected, the hold-down functions for
arming in AWAY Mode, STAY Mode 1 and STAY
Mode 2 are functional. Refer to Section 6.4 Hold-Down
Functions on page 39 for more information.
4 – Single Button Disarming Allowed
This option operates only when Option 2 in this
location is also selected. This option allows hold-
down functions for disarming from STAY Mode 1
and STAY Mode 2. Refer to Section 6.4 Hold-Down
Functions on page 39 for more information.
8 – Alarm Memory Reset on Disarm
If this option is selected, the alarm events memory
clears from the remote codepad when the system is
disarmed. If this option is not selected, the system
must be armed and disarmed again to clear alarm
memory from the remote codepad.
18.7
Consumer Options 3
Location
430
1
Codepad fault beeps allowed
2
Use digit 3 for Codepad Duress Alarm (instead of
digit 9)
4
Alarms activate sirens and strobe outputs in STAY
Mode 1 and 2
8
Reserved
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
System and Consumer Options
1 – Codepad Fault Alarms Beep
If this option is selected, the FAULT indicator flashes
and the codepad beeps once every min until the user
acknowledges a system fault. To acknowledge a new
fault and stop the codepad from beeping once every
min, press [AWAY].
If this option is not selected, only the codepad
FAULT indicator flashes when a new fault occurs
and the codepad does not beep once every min.
2 – Digit 3 for Codepad Duress Instead of 9
If this option is selected, a user can add 3 (instead of
a 9) to the code used to disarm the system to activate
a Duress Alarm.
4 – Alarms Activate Sirens and Strobe Outputs in
STAY Modes 1 and 2
Select this option if audible alarms are required when
the system is armed in STAY Mode 1 or STAY
Mode 2.
18.8
Radio Input Options
431
Location
Default
0
1
WE800/E Radio Receiver
2
Latching keyswitch input
3
Momentary keyswitch input
4
Reserved
1 – WE800/E 304 MHz Receiver
Select this option to use the WE800/E 304 MHz RF
Receiver for remote operations using radio remote
hand-held transmitters.
2 – Latching Keyswitch Input
Selecting this option allows you to connect a latching
keyswitch to the P5 terminals D and GND to
remotely arm and disarm the system in AWAY
Mode.
3 – Momentary Keyswitch Input
Selecting this option allows you to connect a
momentary keyswitch to the P5 terminals D and
GND to remotely arm and disarm the system in
AWAY Mode.
EN | 81
Advertisement
Table of Contents
