Table of Contents
Advertisement
ICP-CC408 | Installation Guide | 4.0
4.6
Disarming the System from STAY
Mode 2
There are two methods to disarm the system from
STAY Mode 2. You can always use the first method.
You can use method two only if Option 4 is enabled
in Location 429 (refer to Section 18.6 Consumer
Options 2 on page 81).
You cannot use method two unless both
Options 2 and 4 are enabled in Location
429.
To disarm the system from STAY Mode 2
(method one):
Enter your code and press [STAY].
Two beeps sound and the STAY indicator is
extinguished. The system is now disarmed.
To disarm the system from STAY Mode 2
(method two):
A flashing zone indicator represents a previous alarm
in that zone. If this is the case, a valid User Code is
required to disarm the system using method one. To
enable method two, Option 4 in Location 429 must
be enabled (refer to Section 18.6 Consumer Options 2 on
page 81).
1. Press and hold [0].
2. When two beeps sound, release the button.
The STAY indicator is extinguished and the
system is disarmed.
Single button disarming from STAY
Mode 2 reports as User Code16.
4.7
Codepad Duress Alarm
Figure 4:
ICP-CP508W LED Codepad Showing
Audible Alarm Buttons
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
System Operations
A codepad Duress Alarm is used as a silent holdup
alarm when 9 is added to the end of a valid User
Code used to disarm the system. If a User Code has
a priority level that allows arming only, that User
Code can transmit a Duress Alarm when the system
is armed.
A Duress Alarm (Contact ID Event Code 121) is
useful only if your system reports to a monitoring
station or pocket pager because domestic reporting
format cannot decipher the type of alarm that
occurred. You can disable the codepad Duress Alarm
Report by programming 0 in Location 336 (refer to
Section 15.8 Codepad Duress Report on page 65). You
can select Option 2 in Location 430 to use 3 instead
of 9 to activate a Duress Alarm (refer to Section 18.7
Consumer Options 3 on page 81).
4.8
Codepad Panic Alarm
An audible codepad Panic Alarm activates when a
user presses the [1] and [3] or [STAY] and [AWAY]
keys simultaneously.
Select Option 1 in Location 425 to program the
codepad Panic Alarm as silent (refer to Section 18.2
System Options 2 on page 79). To disable the codepad
Panic Alarm Report, program Locations 337 and 338
to 0 (refer to Section 15.9 Codepad Panic Report on page
65). A codepad Panic Alarm transmits Contact ID
Event Code 120 if the system reports to a base
station receiver.
4.9
Codepad Fire Alarm
An audible codepad Fire Alarm activates when a
user presses the [4] and [6] keys simultaneously. A
distinct fire sound is emitted through the horn
speaker to indicate this type of alarm. The fire sound
is different than the burglary sound.
Select Option 2 in Location 425 to program the
codepad Fire Alarm as silent (refer to Section 18.2
System Options 2 on page 79). To disable the codepad
Fire Alarm Report, program Locations 339 and 340
to 0 (refer to Section 15.10 Codepad Fire Report on page
66). A codepad Fire Alarm transmits a Contact ID
Event Code 110 to a base station receiver.
4.10
Codepad Medical Alarm
An audible codepad Medical Alarm activates when a
user presses the [7] and [9] keys simultaneously.
Select Option 4 in Location 425 to program codepad
Medical Alarm as silent (refer to Section 18.2 System
Options 2 on page 79). To disable reporting of the
codepad Medical Alarm Report, program Locations
341 and 342 to 0 (refer to Section 15.11 Codepad
Medical Report on page 66). A codepad Medical
Alarm transmits a Contact ID Event Code 100 to a
base station receiver.
EN | 22
Advertisement
Table of Contents
