Setting Stay Mode 2 Zones - Bosch ICP-CC408 Installation Manual

ICP-CC408 | Installation Guide | 6.0
To disable the Telco arming sequence:
Enter the Installer Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy
call forward (no answer off):
1. Enter the Installer Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [2][AWAY] to change the Telco disarming
sequence.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 27 for the indicators and their meanings.
If no Telco disarming sequence is programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the sequence is displayed.
3. Press [STAY][2 6 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the Telco disarming sequence at
any time.
To disable the Telco disarming sequence:
Enter the Installer Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
To program the Telco arming sequence – easy
call forward (immediate on):
1. Enter the Installer Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1][AWAY] button to change the Telco
arming sequence. Three beeps sound.
If a call forwarding sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 27 on page 30 for the indicators and
their meanings.
If no call forward sequence is programmed, an
additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the call forward sequence is
displayed.
3. Press [STAY][1 2 1] and enter the phone number
to which you want calls from the control panel
diverted.
4. Press [STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
Example
If you want to automatically divert all incoming calls
to another telephone number (for example, 9672
1777) when the system is armed in AWAY Mode,
enter:
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
System Functions
[1 2 3 4 3][AWAY][1][AWAY][STAY]
[1 2 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the Telco arming sequence at any
time.
To disable the Telco arming sequence:
Enter the Installer Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy
call forward (immediate off):
1. Enter the Installer Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [2][AWAY] to change the Telco disarming
sequence.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 27 for the indicators and their meanings.
If no Telco disarming sequence is programmed,
an additional two beeps sound after you enter
this mode. These two beeps normally sound after
the last digit of the sequence appears.
3. Press [STAY][2 2 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the Telco disarming sequence at
any time.
To disable the Telco disarming sequence:
Enter the Installer Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
6.1.4

Setting STAY Mode 2 Zones

This function allows the installer to select the zones
that are automatically isolated when the system is
armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and hold
[0] until two beeps sound. Refer to Section 6.4.3 on
page 39 or Section 4.5 Arming the System in STAY Mode
2 on page 21 for more information.
To set STAY Mode 2 zones:
1. Enter the Installer Code and press [4][AWAY].
Three beeps sound and the STAY indicator
flashes.
2. Enter the number of the zone you want to
automatically isolate and press [STAY].
The corresponding zone indicator flashes.
3. Repeat Step 2 for each zone you want to select.
EN | 31