[Pr. Pv29_Acceleration Limit (Acclmt)]; [Pr. Pv31_Deceleration Limit (Declmt)]; [Pr. Pv33_Master-Slave Operation - Speed Limit Adjusted Value Extension Setting (Vlle)] - Mitsubishi Electric MR-J5-G User Manual

[Pr. PV29_Acceleration limit (ACCLMT)]

Initial value
0
Set the acceleration limit value to be used in the profile position mode (pp), profile velocity mode (pv), homing mode (hm), and
JOG operation mode (jg).
The unit can be changed to 0.001 mm/s
If this servo parameter is set to "0", the acceleration limit is disabled.
This function is enabled when [Pr. PT01.1 Speed/acceleration/deceleration unit selection] is set to "1".
The servo motor accelerates by the setting value of this servo parameter when the following conditions are met:
• The setting value of [Pr. PV05 Profile acceleration] is "0" in pp, pv, or jg mode
• The setting value of [Pr. PV15 Homing acceleration] is "0" in hm mode
This function corresponds to [Max acceleration (Obj. 60C5h)].
When the object is mapped to the cyclic communication, do not write values with engineering tools because the controller
overwrites the servo parameter values written with engineering tools.

[Pr. PV31_Deceleration limit (DECLMT)]

Initial value
0
Set the deceleration limit value to be used in the profile position mode (pp), profile velocity mode (pv), homing mode (hm), and
JOG operation mode (jg).
The unit can be changed to 0.001 mm/s
If this servo parameter is set to "0", the deceleration limit is disabled.
This function is enabled when [Pr. PT01.1 Speed/acceleration/deceleration unit selection] is set to "1".
The servo motor decelerates by the setting value of this servo parameter when the following conditions are met:
• The setting value of [Pr. PV07 Profile deceleration] is "0" in pp, pv, or jg mode
• The setting value of [Pr. PV15 Homing acceleration] or [Pr. PV17 Homing deceleration] is "0" in hm mode
This function corresponds to [Max deceleration (Obj. 60C6h)].
When the object is mapped to the cyclic communication, do not write values with engineering tools because the controller
overwrites the servo parameter values written with engineering tools.
[Pr. PV33_Master-slave operation - Speed limit adjusted value
extension setting (VLLE)]
Initial value
0 [Refer to the text below for the unit.]
Set the minimum value of the slave axis speed limit for the slave axis torque mode (slt).
The unit can be changed to pulses/s with [Pr. PT01.2 Unit for position data].
This servo parameter is enabled only in the slave axis torque mode.
This function is enabled when [Pr. PT01.1 Speed/acceleration/deceleration unit selection] is set to "1". This function and [Pr.
PD32 Master-slave operation - Slave-side speed limit adjusted value] are mutually exclusive.
This function corresponds to [Master-slave Lower limit of velocity limit value (Obj. 2E46h)].
When the object is mapped to the cyclic communication, do not write values with engineering tools because the controller
overwrites the servo parameter values written with engineering tools.
Setting range
0 to 4294967295
2 2
, 0.0001 inch/s , 0.001 degree/s
Setting range
0 to 4294967295
2 2
, 0.0001 inch/s , 0.001 degree/s
Setting range
0 to 4294967295
1.11 Positioning extension setting servo parameters group ([Pr. PV_ _ ])
Setting method
Each axis
2 2
, or pulse/s with [Pr. PT01.2 Unit for position data].
Setting method
Each axis
2 2
, or pulse/s with [Pr. PT01.2 Unit for position data].
Setting method
Each axis
1 SERVO PARAMETER DETAILS
Ver.
C0
Ver.
C0
Ver.
D0
183
1