Table of Contents
Advertisement
RHCPLWSUswpmf
SERVICE MENU
SENSOR CHECK
*** * ****
SERVICE MENU
THERMISTOR CHK
BOARD:25 C/ 77 F
THERMISTOR CHK
THERMISTOR CHK
BOT. :25 C/ 77 F
THERMISTOR CHK
HEAD1:25 C/ 77 F
THERMISTOR CHK
HEAD6:25 C/ 77 F
SERVICE MENU
SUB MENU
SUB MENU
SERIAL NO.
SUB MENU
CHANGE INKTYPE
SUB MENU
FILL INK
SUB MENU
HEAD WASH
M123456
C123456
***
***
This menu displays the real-time status of all sensors.
When a sensor is ON, * will be displayed.
The first page shows all sensors ON/OFF.
Each alphabet stands for as follows.
R : Paper Sensor Rear
H : Limit Sensor
C : Front Cover Sensor
P : Maintenance Cover R Sensor
L : Pinch Lever Sensor
W : Paper Side Sensor
S : Ink Cover Sensor
U : Head Up/Down Sensor
This menu is for Thermistor Checking. You can check the temperature for following thermistors.
HEAD1-6 : located at print head boards, BOARD : located at Head Board, BOT : located under BED.
Left digits for Fahrenheit, right digits for Celsius.
[HEAD] and [BOARD] may show higher temperature than the ambient of the usage environment, due to heated devices on Head Board.
Check if any big difference displayed comparing to the ambient. The temperature of [HEAD] and [BOARD] may not be identical.
SERIAL NO.
ZS00000
This menu is to input Serial number of the machine consisting of seven digits. [
CHANGE INKTYPE
EXt
Ink
LcLm
This menu is to change Ink Type. Different from the process in user menu, Head Wash or Ink Fill will not be required.
This process should be made for curing purpose e.g. wrong ink type installed.
When you change Ink Type, ink system will be initiallized internally, then, returns un-setup getting out of menu.
INKTYPE
EXt Ink LcLm : EcoXtreme Ink KCMYLcLm
LIQUID
: Maintenence Liquid
EMPTY
: Not Filled
UNKNOWN
: Fill Ink uncompleted or ink type not detected.
DEFAULT
EMPTY
FILL INK
123456
Fill ink to each print head.
By [
] and [
] keys to move cursor, by [
] and [
Before performing Fill Ink, following message will show up to prevent drain from flowing out.
EMPTY
DRAIN BOTTLE
When [ENTER] key was pressed, Fill Ink starts for the selected in ON.
HEAD WASH
WASHING HEAD...
>
123456
This menu is to wash each print head or to select storing method.
By [
] and [
] keys to move cursor, [
] and [
Before performing Fill Ink, following message will show up to prevent drain from flowing out.
EMPTY
DRAIN BOTTLE
If you press [ENTER] key, HEAD WASH starts on the selected HEAD.
If you press [ENTER] key while none of HEAD number selected, HEAD WASH will not run, and a message to select storing method will show up.
After HEAD WASH completed, print heads will be capped, then goes to STORAGE stage.
CANCEL : STORAGE is not done, and HEAD WASH will be completed.
SET
: Go to STORAGE. Print head carriage goes in standby state. Then, cover cap tops with film.
COVER CAP
WITH FILM
After covering film, press [ENTER] key. Print heads will be capped and become standby state.
After confirming standby state, replace cartridges with dummy cartridges.
SET DUMMY
CARTRIDGE
After inserting dummy cartridges, press [ENTER] key. Set the supply pump opened, then go back to HEAD selecting in HEAD WASH menu.
Make sure dummy cartridges are inserted firmly. Maintenance liquid may flow out.
4-6
P123456
***
The second page shows status for each sensor.
M : Max Sensor for each Sub Tank
s : Slide Sensor
C : Ink Cartridge IC Board for each cartridge
w : Wiper Sensor
P : Pressure Pump Magnet Sensor for each cartridge
p : Maintenance Liquid Pump Magnet Sensor
S : Supply Pump Magnet Sensor for each cartridge
m : Maintenance Liquid Cartridge IC and
Maintenance Liquid Empty Sensor
f : Rear Dancer Roller Sensor
] and [
] keys for moving digit, [
FILL INK...
>
] keys to select ON/OFF. To back out from menu, press [
STORAGE
CANCEL
STORAGE
SET
] keys to select ON/OFF. To back out from the menu, press [
S123456
***
C : Cartridge inserted, Ink remians
E : Cartridge not inserted, Ink empty
* : Cartridge inserted, Ink empty
Space : Cartridge not inserted, Ink remains
] and [
] for selecting number.
] key when a cursor is at Head1.
NOW PROCESSING..
] key when a cursor is at Head1.
Advertisement
Table of Contents
