Table of Contents
Advertisement
SERVICE MENU
PREHEAT TEMP.
SERVICE MENU
HEAT TIMEOUT
SERVICE MENU
HEATER CHECK
SERVICE MENU
SYSTEM SWITCH
SYSTEM SWITCH
PAGE1
SYSTEM SWITCH
PAGE16
This menu is for changing the functions of the machine. It is not necessary to change any switches.
Each bit can be selected by [
Bit
PAGE1 : Bit1
PAGE1 : Bit2
PAGE1 : Bit4
PAGE2 : Bit6
SERVICE MENU
HISTORY MENU
SERVICE MENU
REPORT
PREHEAT TEMP.
This menu is to set heater temperature in unsetup status.
Temperature of [PREHEAT] under the [PREHEATING] in the USER MENU can be set.
HEAT TIMEOUT
This menu is to set Heater Timeout until showing a check message since printing starts while heater controlling.
If the temperature does not reach to the targeted temperature and passed over the set time with printing remains not started,
the message of "CHECK HEATER VOLTAGE SETTING" is displayed.
PRE-R
PRE-F
PRE-R
PRE-F
PRINT
DRYER A
DRYER B_ 25 C
DRYER C
This menu is to check Heaters and Thermistors.
While in this menu, ON/OFF and the temperatures read by thermistors on each Preheater R, Preheater F, PrintHeater, Dryer A-C
will be displayed. [
( "ON/OFF" described here stands for power distributed or not. Thus, the heater is not operated to control temperature which was set in
another menu. Be careful that a heater may be heated too much if it was left ON for a while. When out of menu, all turns OFF automatically.)
Check if the temperature rises when the heater was ON and if the heater gets ambient temperature when it was OFF.
bit # [ 1 2 3 4 5 6 7 8 ]
bit # [ 1 2 3 4 5 6 7 8 ]
] and [
] keys and it can be changed with [
Contents
Front Cover Sensor
0 : Standard Enable
Pump Cover Sensor
0 : Standard Enable
Reflection to the test pattern of
0 : No reflect
a heater related parameters
Base Head Menu
0 : Disable
HISTORY MENU
HEAD GROUP
[
] and [
] keys are to select upper row showing corresponding value in bottom row. Refer to next page for history list.
[
] key to show [CLEAR], and to press [ENTER] key to clear.
REPORT
SERVICE
REPORT
HISTORY
REPORT
CARTRIDGE
REPORT
EVENT LOG
Range:100LOGS/200LOGS/ALL
REPORT
ALL
REPORT
SERIAL
SERVICE : Service Report will be printed. Information necessary for service activity will be printed together with the system report.
250mm wide 230mm long space required, each print head can print it. (Head number starts from left, H1, H2.....H6)
HISTORY : History Report will be printed. 250mm wide 130mm long space required.
CARTRIDGE : Ink Cartridge IC Report will be printed. 180mm wide 40mm long space required.
EVENT LOG : Event Log Report will be printed. 100 LOGS requires 250mm wide 150mm long space.
ALL : All Reports to print (System Report, Service Report, History Report, Ink Cartridge IC Report, Event Log Report) requires
1200mm (48inch) wider space and it reaches 180mm long.
SERIAL : Serial Report Menu will be printed through the RS-232C Serial with the special tool.(9600bps N81 XON/XOFF)
OFF,20~40 C
35 C
35 C
Default : 35 C
OFF,20~40mins
OFF
10min
Default:30mins
_ 25 C
Preheater R : OFF
25 C
_
* 40 C
Preheater R : ON
25 C
_ 25 C
25 C
25 C
] and [
] keys are to select heater, [ENTER] key is to turn ON, and to press [ENTER] key again is to turn OFF.
PAGE1
00000000
PAGE16
00000000
] and [
] keys. There are 16 pages for 8 bits System Switch.
Settings
1 : Disable (always closed status)
1 : Disable (always closed status)
1 : Reflect
1 : Enable
SHOT COUNT 1
26103 KShot
SERVICE
HEAD H1
H1/H2/H3/H4/H5/H6
HISTORY
HEAD H1
H1/H2/H3/H4/H5/H6
CARTRIDGE
HEAD H1
H1/H2/H3/H4/H5/H6
NUM PRINT LOGS
100 LOGS
ALL
HEAD H1
200 LOGS requires 250mm wide 280mm long space.
ALL requires 250mm wide 540mm long space.
4-9
(every 10mins)
Default
0
0
0
0
SHOT COUNT 1
CLEAR
EVENT LOGS
HEAD H1
Advertisement
Table of Contents
