YASKAWA A1000 Series Quick Start Manual page 149

No. Name
Excessive Speed Deviation
F1-11
Detection Delay Time
F1-12 PG 1 Gear Teeth 1
F1-13 PG 1 Gear Teeth 2
PG Open-Circuit Detection
F1-14
Time
F1-18 dv3 Detection Selection
F1-19 dv4 Detection Selection
F1-20 PG Option Card Disconnect
Detection 1
F1-21 PG 1 Signal Selection
PG Card Option Port for
F1-30
Motor 2 Selection
F1-31 PG 2 Pulses Per Revolution
F1-32 PG 2 Rotation Selection
F1-33 PG 2 Gear Teeth 1
F1-34 PG 2 Gear Teeth 2
PG 2 Division Rate for Pulse
F1-35
Monitor
PG Option Card Disconnect
F1-36
Detection 2
F1-37 PG 2 Signal Selection
<10> Default setting is determined by the control mode (A1-02).
<45> Regional default settings
Setting 600 ppr: Japan (Model code: CIMR-AA A) and Asia (Model code: CIMR-AT A)
Setting 1024 ppr: China (Model code: CIMR-AB A)
F2: Analog Input Card (AI-A3)
■
No. Name
Analog Input Option Card
F2-01
Operation Selection
YASKAWA ELECTRIC TOEP C710616 21C YASKAWA AC Drive - A1000 Quick Start Guide
Sets the time in seconds for a speed deviation situation to trigger a fault (dEv).
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if either of these parameters is set to 0.
Sets the time required to trigger a PG Open fault (PGo).
0: Disabled
1: Enabled
0: Disabled
n: Number of pulses that the A and B pulse are reversed that triggers dv4
detection.
0: Disabled
1: Enabled
0: A pulse detection
1: AB pulse detection
Sets the port for the PG option card used by motor 2.
0: CN5-C
1: CN5-B
Sets the number of pulses for a PG option card connected to port CN5-B.
0: Pulse A leads
1: Pulse B leads
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if either of these parameters is set to 0.
Sets the division ratio for the pulse monitor used of the PG option card 2
installed to connector CN5-B. By setting "xyz", the division ratio becomes = [(1
+ x) / yz].
0: Disabled
1: Enabled
0: A pulse detection
1: AB pulse detection
0: Option card input terminals V1, V2, and V3 replace drive input terminals A1,
A2, and A3.
1: Input signals to terminals V1, V2, and V3 are added together to create the
frequency reference.
Description
Description
B Parameter List
Setting
Default: 0.5 s
Min: 0.0 s
Max: 10.0 s
Default: 0
Min: 0
Max: 1000
Default: 0
Min: 0
Max: 1000
Default: 2.0 s
Min: 0.0 s
Max: 10.0 s
Default: 10
Min: 0
Max: 10
Default: 128
Min: 0
Max: 5000
Default: 1
Min: 0
Max: 1
Default: 0
Min: 0
Max: 1
Default: 1
Min: 0
Max: 1
Default:
<45>
Min: 0 ppr
Max: 60000 ppr
Default: 0
Min: 0
Max: 1
Default: 0
Min: 0
Max: 1000
Default: 0
Min: 0
Max: 1000
Default: 1
Min: 1
Max: 132
Default: 1
Min: 0
Max: 1
Default: 0
Min: 0
Max: 1
Setting
Default: 0
Min: 0
Max: 1
B
149