Toshiba e-STUDIO 2555C Service Manual page 1130

Sub
05/08 Mode Element
element
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Aligning Batch conversion
t mode adjustment
05 Adjustmen Printer Finisher Alignment position
t mode adjustment
05 Adjustmen Printer Finisher Alignment position
t mode adjustment
05 Adjustmen Printer Finisher Stapling position
t mode adjustment
05 Adjustmen Printer Finisher Stapling position
t mode adjustment
05 Adjustmen Printer Finisher Stapling position
t mode adjustment
05 Adjustmen Printer Finisher Stapling position
t mode adjustment
05 Adjustmen Printer Finisher Stapling position
t mode adjustment
05 Adjustmen Printer Finisher
t mode
05 Adjustmen Printer Finisher
t mode
05 Adjustmen Printer Finisher Saddle stitch
t mode
05 Adjustmen Printer Finisher
t mode
Item Subitem Code
Thick paper 2 4810
Thick paper 2 4810
Thick paper 2 4810
Thick paper 3 4811
Thick paper 3 4811
Thick paper 3 4811
4822
4822
4823
4823
4823
4823
4823
4824
4825
4826
4827
Sub- Default Acceptable
Details
code value value
0 Drawer 0 -20-20
1 Bypass feeding 0 -20-20
2 ADU 0 -20-20
0 Drawer 0 -20-20
1 Bypass feeding 0 -20-20
2 ADU 0 -20-20
0 Front 0 -17-17
1 Rear 0 -17-17
0 Rear – One place 0 -25-25
1 Rear – One place (R- 0 -17-25
series size)
2 Front – One place 0 -25-25
3 Front – One place (R- 0 -25-17
series size)
4 Center – 2 places 0 -17-17
Adjustment of hole 0 -15-15
punch center position
Adjustment of hole 0 -20-12
punch position
Adjustment of 0 -15-15
alignment position
Adjustment of ejection 0 -15-15
position of gripper
71
RAM Contents
M 0.6 mm/step
M 0.6 mm/step
M 0.6 mm/step
M 0.6 mm/step
M 0.6 mm/step
M 0.6 mm/step
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
M 0.2mm/step
* This code is not supported by LL20/25ppm model.
Proce Servic
dure e UI
4
4
4
4
4
4
4 Yes
4 Yes
4 Yes
4 Yes
4 Yes
4 Yes
4 Yes
1 Yes
1 Yes
1 Yes
1 Yes