Page 2 IMPORTANT THE INFORMATION CONTAINED HEREIN IS PUBLISHED BY CANON, INC., JAPAN, AND IS FOR REFERENCE USE ONLY. SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER PRINTED MATTER. ANY QUESTIONS REGARDING INFORMATION CONTAINED HEREIN SHOULD BE DIRECTED TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.
Page 3 INTRODUCTION This Service Manual provides basic facts and figures needed to service the GP215/GP200 in the field. The GP215/GP200 is designed to accommodate fax and printer functions in addition to copier functions, and separate service manuals are available for each function; refer to the appropriate service manual as necessary.
Page 4 GP200F (w/ fax function, w/o duplexing function) GP200 (w/o fax function, w/o duplexing function) Multi-Output Tray-C1 Multi-Output Tray-B2 Handset Cassette Feeding Unit-L1 Cassette Feeding Unit-M1 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 5: Table Of Contents
Making Two-Sided Copies....3-106 A. High-Voltage Transformer Circuit ..3-58 Lower Feeding Assembly .....3-108 Controlling the K. Fixing/Delivery Assembly .....3-118 Primary Charging Roller Bias..3-60 Delivery Assembly ......3-127 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 6 COPY DATA CONTROLLER-A1 ....5-34 CHAPTER 6 MAINTENANCE AND SERVICING PERIODICALLY REPLACED PARTS ..6-1 III. SCHECULED SERVICING CHART ..6-2 CONSUMABLES AND DURABLES ..6-1 SCHEDULED SERVICING......6-4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 7 COMPOSITE POWER SUPPLY ANALOG PROCESSOR CIRCUIT CIRCUIT DIAGRAM ......A-29 DIAGRAM..........A-20 LIST OF SPECIAL TOOLS ....A-37 LASER DRIVER CIRCUIT DIAGRAM ..A-24 SOLVENTS/OILS ........A-38 PICK-UP UNIT CIRCUIT DIAGRAM..A-26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 9 C. Arrangement of Extension Boards ..1-12 VI. SAFETY..........1-30 OPERATION ..........1-13 A. Laser Beams ........1-30 A. Turning On the Power Switches ..1-13 Safety of Toner .......1-31 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 11: Chapter 1 General Description
• The machine is appreciably quieter than the existing models for a better office environment. • With the help of its power-saving design, the power consumption is 4 W or less* in sleep mode (about 1/25 of existing Canon models) and 57 W or less** in standby (about 1/4 of exist- ing Canon models).
Page 12: Specifications
Automatic 2 cassettes Pick-up Manual Multifeeder (about 5 mm deep) Transfer Roller charging Separation Static (static eliminator) + curvature cleaning Blade Fixing SURF 1–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 13 Plain paper (64 to 128 g/m (no overlay copying) copying feeder *Canon recommended paper. *May be used but may not feed as expected. 1–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 14 ADF·F1 RF·G1 Sorter Multi-Output Tray -C1 Multi-Output Tray -B2 Pedestal Cassette Feeding Unitl-L1 Cassette Feeding Unitl-M1 Others Handset-A1 Control Card V Film Projector 1–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 15 72.4kg (w/ copyboard cover) w/ ADV 77.1kg w/ RDF 84.7kg Consuma Copy paper Toner Keep copy paper wrapped to protect against humidity. bles 1–5 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 16 A5R (210 × 148.5mm) B4 (267 × 364mm) B5 (182 × 257mm) B5R (257 × 182mm) Reduce Enlarge Table 1-201 Copying Speed (copier only) 1–6 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 17 LGL → 11×17 ENLARGE LTR·R → 11×17 STMTR → 11×17 Table 1-202 Copying Speed (copier only) Specifications subject to change for product improvement. 1–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 18: Names Of Parts
Control panel power switch i Front door r Original delivery tray (for RDF) o ADF-F1 t Multifeeder !0 Original delivery tray (for ADF) 1–8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 19 !1 Cassette heater (option) switch !2 Service switch !3 Counter (total) !4 Counter (printer) !5 LCD display contrast adjust- SLEEP 1 ment SLEEP 2 Figure 1-303 1–9 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 20: Cross Section
1. GENERAL DESCRIPTION B. Cross Section 1. Cross Section of the GP215 9 10 11 12 13 14 15 16 Figure 1-304 1–10 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 21 #6 Fixing assembly !8 Vertical path roller 2 #7 Delivery roller 1 !9 Cassette pick-up feeding (lower) #8 Paper deflecting plate #9 Delivery roller 2 1–11 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 22: Arrangement Of Extension Boards
CIST Board i Protocol Controller Board e CORE/IP Board o Network Interface Board r FAX Motherboard !0 G3FAX board t Printer board 1–12 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 23: Operation
You must first turn on the main power switch and then the control panel switch whenever you are turn- ing on both switches. Figure 1-401 q Control panel power switch w Main power switch e Main power supply lamp 1–13 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 24: Control Panel
User mode key y Start key !0 Guide key !1 Reset key !2 Power supply lamp *If for North America, ‘PRINT I/F’. 1–14 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 25 DEN- IMAGE RESOL. DIRECT SITY QUALITY CODED ON-HOOK REDIAL DIALING SPECIAL FEATURES MONITOR Figure 1-404 Note: For details, see the Fax Service Manual. 1–15 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 26: Basic Operation
2. Using the Preference key, the most frequently used modes may be selected for display. To select, use ‘custom copy setting’ in user mode. 3. The DEF. SIZE ORIGINAL key is effective only when an RDF is installed. 1–16 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 27 2) Place the original, and press the Start key. c. Interrupt key 3) To end interrupt mode, press the Interrupt d. Copy Density key (from AE to manual) mode once again. 1–17 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 28 2) On the ‘DEPT. ID MANAGEMENT’ screen select ‘ON’ and then ‘COPY TOTALS’; then, press ‘CLEAR ALL TOTALS’. Note: You cannot clear the counts individually. 1–18 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 29: Extension Mode
INTERLIVING SHEET DIF.SIZE MARGIN OVERLAY ORIGINAL AREA FRAME SHARPNESS DESIG. ERASE IMAGE IMAGE CREATION COMB. IMAGE SEPARATION MODE REC. MEMORY DONE Figure 1-405 1–19 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 30 1-on-2, 1-on-4, 1-on-2 / One-sided, 1- Requires an RDF. on-4 / One-Sided MODE MEMORY M1 through M5 REC. Most Recent, 2nd Most Recent, 3rd Most Recent 1–20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 31 SHEET • Making an overlay copy from two one-sided ordinals. Overlay • Making an overlay copy from an open original (book). Book Overlay 1–21 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 32 Erase Original Copy Book Frame 2.5mm Erase 2.5mm Binding Erase e Book Frame Erase r Binding Erase 2.5mm 2.5mm 2.5mm 10mm 2.5mm 1~20mm 1–22 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 33 You can use a film projector to copy photo film, which may be either of four types. 35mm Negative 35mm Negative 4 × 5 Negative 4 × 5 Positive 1–23 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 34 Standard settings You can store/initialize the combination of copying modes in response to power-on or a press on the Reset key. Store Init. 1–24 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 35: Custom Common Settings
Cassettes 1 auto cassette selection. through 6: ON ON: To include in auto selection. OFF: To specify inclusion only in manual mode. 1–25 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 36 (group ID and ID numbers). tration: No ID/PASSWORD COPY TOTALS — INITIALIZE COMMON Allows you to return the custom settings to CUSTOM SETTINGS their defaults. 1–26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 37: Timer Setting
TINGS panel power switch is automatically turned day from Sunday off at a specific time on specific days of the to Saturday) week. 1–27 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 39: Routine Work By The User
Wipe it with a moist cloth; thereafter, dry wipe 2) Copyboard Cover/RDF Feeding Belt Wipe them with a cloth moistened with a solu- tion of mild detergent; then, dry wipe them. 1–29 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 40: Safety
In the copier, the label is attached to the laser scan- ner system cover, which is used to prevent radiation of laser lights. Figure 1-602 220/240V Model 1–30 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 41: Safety Of Toner
Further, do not bring toner into con- tact with plastic material, as such will initiate chemical reaction. Caution: Do not dispose of toner in fire. It may explode. 1–31 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 43 C. Pre-Exposure (step 1) ......2-3 Fixing (step 7)........2-7 Primary Charging (step 2) ....2-3 Dram Cleaning .........2-7 E. Laser Exposure (step 3) ....2-4 AUXILIARY PROCESS......2-8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 45: Chapter 2 Copying Process
2. COPYING PROCESS I. IMAGE FORMATION A. Outline The GP215/GP200 uses an indirect photographic method of reproduction and is constructed as shown in Figure 2-101. Copyboard glass Scanning lamp Lens Image processing assembly Primary charging Laser scanner assembly roller Developing...
Page 46: Latent Image Formation Block
(dark areas of originals) Substrate -500 Figure 2-103 Dark areas (areas not exposured by the laser) -1000 Laser exposure (step 3) Figure 2-104 2–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 47: Pre-Exposure (Step 1)
An AC bias is applied to stabilize the charges applied to the photosensitive drum. The primary charging roller is a special roller and is not the same as the transfer roller. 2–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 48: Laser Exposure (Step 3)
Developer Blade Concentrated magnetic field Magnet Magnet Figure 2-109 2–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 49: Transfer (Step 5)
If separated completely, the transfer guide would be charged, soiling the transfer guide and ultimately soiling the back of copy paper. 2–5 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 50: Separation (Step 6)
To prevent such a problem, a negative voltage is applied to the separation static eliminator, thereby weakening the static bond between drum and Figure 2-112 copy paper for better separation. 2–6 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 51: Fixing (Step 7)
The metal core of the lower fixing assembly is given a positive bias to prevent offset of toner to the fixing film. 2–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 52: Auxiliary Process
Copy paper immediately prior to delivery holds residual charges from transfer, and a static elimi- nator (grounded brush) is provided at the delivery slot to remove such charges. 2–8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 53 Pick-Up from the Cassette .....3-79 Self Diagnosis of the C. Non-Pick Up Operation (standby)..3-91 Multi Output Tray-12 .....3-268 Detecting the Level of Copy Paper ...3-93 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 55: Basic Operation
3. OPERATIONS AND TIMING I. BASIC OPERATION A. Functional Construction The GP215/GP200 can be divided into seven functional blocks: pick-up/feeding system, original expo- sure system, image processing system, laser exposure system, image formation system, communication system, and control system. <Original exposure system>...
Page 56: Outline Of The Electrical Circuitry
B. Outline of the Electrical Circuitry 1. Control Division The GP215/GP200’s electrical mechanisms are controller by the CPU on the PCBs shown in Figure 3- 102. See Table 3-101 for an idea of the functions of the CPU and the functions of the ROMs/RAMs and the ICs around the CPU.
Page 57 • Monitors the CI (calling indicator; fax call signal) • Controls the power supplies of loads • Controls the scanning lamp Table 3-101c 3–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 58 Q605 DC loads Clutch IC104 Solenoid Motor Sensor -12V IC105 Etc. Laser scanner motor IC108 Sorter RDF/ADF Communication control device Figure 3-102 3–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 59: General Block Diagram
Figure 3-103 Note: The CORE/IP Board, FAX Motherboard, and G3 FAX Board come standard with the GP215F/GP200F but are options for other models (GP215/GP200). 3–5 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 60: Inputs To The Major Pcbs
FL1 Scanning lamp J205-3 J205-3 Primary charging roller Developing assembly Drum Transfer guide J206-1 Static eliminator T502 Transfer roller J206-4 J220 Fixing assembly Figure 3-104 3–6 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 61 When '1', LED turns ON. (Turns ON when the main power switch is ON.) Power saving mode switch J560 J183 Control Card V (option) Figure 3-105 3–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 62 J508 Original size D S Z 4 sensor 4 Motherboard Board Checks are not meant for the field. G3 FAX Board Figure 3-106 3–8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 63 Checks are not meant for the field. One-touch dial cover open/closed detection Touch panel J516 LCD back-light power supply BKLTON When '0', the back-light turns Figure 3-107 3–9 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 64 J113 When the waste toner case Waste toner is full, '0'. WTDT sensor (The light-blocking plate PS10 is not at PS10.) Figure 3-108 3–10 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 65 J113 -A15 Detects the width of Multifeeder paper -A14 MFPW copy paper stacked width detection (analog signal) in the multifeeder. -A13 Figure 3-109 3–11 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 66 When Q1607 has detected 1RPD1 Q1607 level detection 1 the lifter, '1'. J122 When Q1609 has detected 2RPD1 Q1609 the lifter, '1'. Figure 3-110 3–12 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 67 24V24V J105-A8 Delivery reversing See p. 3-127 motor -A10 (GP215 only) -A11 24V24V J115-1 See p. 3-114 Horizontal motor Figure 3-111 3–13 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 68 Laser cooling fan low-speed modes. The CPU control J112-9 mechanism switches 24VU between high-speed and System cooling fan low-speed modes. Figure 3-112 3–14 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 69 While M4 is rotating, · alternates between '1' and '0'. Motor Cassette (pulse signal) drive pick-up motor 12M0 circuit · Always '1'. 12M1 Figure 3-113 3–15 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 70: Main Motor Control Pcb
At this time, the output of the hall IC is returned to the drive circuit, thereby maintaining the rotation of the motor. 3–16 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 71 Main Drive DC controller PCB motor circuit (M1) Encoder J114-B6 Control circuit Hall IC output MLCK* Output pulse J114-B7 Reference signal Figure 3-114 3–17 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 72 Note 1: A key on the control panel is pressed, or an original is placed in the feeder. Note 2: Varies according to the time set in user mode (quiet mode). 3–18 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 73 LSTR, the indications on the control panel return to the Standard screen indications. (The time may be changed in com- mon settings mode.) Table 3-102 3–19 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 74: Original Exposure System
Image processing system Image processor CORE/IP Board Laser beam Printer Laser Laser Board Board Driver Laser mirror Laser exposure system Photo- sensitive drum Figure 3-201 3–20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 75 3. OPERATIONS AND TIMING Scanner motor Scanner home position sensor Forward No. 1 mirror mount Reverse Mirror mount Figure 3-202 3–21 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 76: Varying The Reproduction Ratio
ON LSTR STBY INTR SCFW SCFW SCFW STBY Forward Reverse Scanner motor (M2) Scanner home position sensor (PS1) Scanning lamp (FL1) Figure 3-203 3–22 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 77: Scanner Motor
(M2). DC controller Motor controller Figure 3-204 • Outline of Power Supply to M2 Figure 3-205 3–23 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 78: Controlling The Scanning Lamp
Scanning lamp intensity sensor T101 Drive circuit Logic circuit Q605 DC controller PCB IC 102 Gate array IC101 Figure 3-206 3–24 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 79 PCB. The logic circuit uses these two signals to generate the scanning lamp ON signal, thereby turning ON the scanning lamp. 3–25 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 80: Identifying The Size Of Originals
Sensor 0 Sensor 1 Sensor 2 Sensor 3 • Inch-Configuration Sensor 0 Sensor 1 STMT LTRR Sensor 2 11x17 Figure 3-207 (arrangement of original sensors) 3–26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 81 Copyboard cover Original 30˚ PS3:ON Copyboard glass Change Original Original change in the detection 1 detection 2 in the level level Figure 3-208 3–27 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 82: Detecting The Size Of Originals
Table 3-201 (AB-configured original) Original size sensor Size 11”×17” Same Same Same Different Same Same LTR-R Different Same Different Same Different Different Table 3-202 (Inch-configured original) 3–28 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 83: Image Processing
Video signal G3 FAX switching circuit Board/NCU Printer Board Command conversion circuit Network I/F Board Protocol controller PCB Figure 3-301 3–29 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 84 To the telephone line. • Rotation • Protocol control Protocol controller PCB • Protocol exchange (between Printer Board and Network Interface Board) Table 3-301 3–30 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 85: Analog Image Processing
(It also executes AE measurement.) 2. CCD/CCD Driver The GP215/GP200’s CCD is a linear image sensor consisting of a single line of 7500 photocells. The signals subjected to photoelectric conversion in the photocell unit are forwarded to the CCD drive circuit.
Page 86 The reference voltage obtained here is sent to the A-D conversion circuit. The “priority on speed” function may be adjusted in service mode ( * 3 * ); see p. 3-204 3–32 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 87: Digital Image Processing
. Repeat . Folding Image processor PCB Area signal generation Binary processing Density Laser driver Synthesis processing conversion OCRE / IP Board Figure 3-304 3–33 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 88: Shading Correction
Scanning lamp before correction No. 2 mirror No. 1 mirror Original density Standard white plate Lens Figure 3-306 No. 3 mirror Figure 3-305 3–34 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 90 Reading starts with this pixel. Reading starts a b c with this pixel. Memory> a b c a b c Figure 3-310 Figure 3-311 3–36 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 91 Area to be shifted Center shift (may be entire original) Original Xmax Copy paper Ymax Free shift Xmax Copy paper Ymax Figure 3-312 3–37 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 92 Breadthwise ratio 2-on-1 (overlay) Required Not Required 2-on-1 (continuous) Not Required Required 2-on-1 (two-sided) Required Required 4-on-1 Not Required Not Required Table 3-303 3–38 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 93 • RDF in use Original Copy Combines the following: • Reduced copying • Image shifting copying • Overlay copying copying Figure 3-314 2-on-1 Mode (overlay) 3–39 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 94 Copy As such, the orientation of the originals copying on the ADF’s original tray is reversed instead of normal Figure 3-315 4-on-1 Mode 3–40 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 95 • The image (original length) of continuous 2-on-1 is divided horizontally for output. • Originals may be placed on the copyboard or in the RDF-G1 (not ADF-F1). Figure 3-316 3–41 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 96 • No number of effective areas of the last original is specified; i.e., the same as in the case of 4-on-1, gen- erating 4 outputs. Figure 3-319 3–42 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 97 1 2 3 4 5 6 7 - 2 - 1 1 pixel (1 byte) Writing Reading 1 pixel (1 byte) Figure 3-321 Reading Figure 3-323 3–43 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 98 • • • 1 pixel (1 byte) Reading 1 pixel (1 byte) 1st line 2nd line Reading 3rd line 4th line Figure 3-325 Figure 3-327 3–44 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 99 Black 255 Main scanning direction Main scanning direction White White After output After output Figure 3-328b Sharpness Mode Weak Figure 3-328c Sharpness Mode Strong 3–45 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 100 Figure 3-331 Image Data of a Photo Figure 3-329 Image Data of Characters Black 255 Main scanning direction White Figure 3-330 Image Data of Characters after Outline Processing 3–46 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 101 Memory Unit (option) is installed. Images stored in the retention memory in advance and the image on the copyboard glass are synthesized for output. Figure 3-333 3–47 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 102 Output level Figure 3-338 Copy density Text mode Text / photo and photo mode Input level Figure 3-337 Density of original Figure 3-339 3–48 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 103 Density of orignal AE Table for Background Type AE Table for Reversal Type AE Table for Other Type Figure 3-340 Figure 3-341 Figure 3-342 3–49 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 105: Laser Exposure System
Image processing system Image processor CORE/IP Baord Laser beam Printer Laser Laser Board Board Driver Laser mirror Laser exposure system Photo- sensitive drum Figure 3-401A 3–51 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 106 6-facet mirror Laser scanner BD PCB Imaging motor drive PCB lens Laser mirror Laser unit Laser driver PCB Photosensitive drum BD mirror Figure 3-401B 3–52 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 107: Generating The Bd Signal
(BD) is used to generate such a start signal. The GP215/GP200 is designed to detect the edge of copy paper which has been re-picked up for two- sided/overlay copying to measure the discrepancy, if any, toward the rear/front.
Page 108: Laser Driver Circuit
The optical output of the laser (semiconductor laser) is affected largely by changes occurring in the ambient temperature. The GP215/GP200 uses a control mechanism which varies the laser drive current automatically to suit the ambient temperature, thereby ensuring a specific output.
Page 109 Each of these laser outputs is used for its respective mode as shown: Laser output Mode High Text mode, text/photo mode Medium Photo mode, FAX output Printer output 3–55 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 110: Controlling The Laser Scanner Motor
6-facet mirror DC controller PCB Laser scanner motor drive PCB 24VU Laser scanner motor Motor drive (M3) circuit Hall IC LOCK output Figure 3-405 3–56 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 112: Image Formation System
Primary charging roller Developing assembly Drum HVT circuit Transfer guide J206-1 Transfer roller T502 Static Lower fixing eliminator J206-4 roller J220 Figure 3-501 3–58 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 113: Fixing (Step 7)
Primary charging roller bias AC component Transfer charging roller Separation static eliminator Developing bias DC component Developing bias AC component Transfer guide bias Fixing bias Figure 3-502 3–59 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 114: B. Controlling The Primary Charging Roller Bias
AC drive circuit T101 Drive circuit current Frequency division setection Q605 J209-B6 J209-B2 J209-A4~A9 J102-B9 J102-A1~A7 J102-B5 IC101 DC controller PCB Figure 3-503 3–60 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 115: Controlling The Primary Charging Roller Bias
(AC control signal PAPWM) and the AC bias cur- rent value it has received to generate signals to drive the transformer T300, thereby controlling the AC bias to a constant current. 3–61 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 116 • During initial rotation after turning on the power switch on the control panel • During post rotation after generating 500 copies/printouts 3–62 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 117: Controlling The Transfer Charging Roller Bias
Constant current control 24VR T101 drive Overcurrent circuit detection Q605 J209-B4 J209-B5 J209-A4~A9 J102-B7 J102-A1~A7 J102-B6 IC101 DC controller PCB Figure 3-504 3–63 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 118 ON key ON STBY SLEEP INTR SCFW LSTR STBY SCFW Main motor (M1) Cleaning bias Reference bias Sheet-to-sheet bias Transfer bias Figure 3-505 3–64 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 119 (negative) to the transfer charging roller. The timing at which the cleaning bias is applied is determined by serial communication data exchanged with the DC controller PCB. 3–65 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 120: Controlling The Developing Bias
T101 drive circuit Voltage Developing detection cylinder circuit Q605 J209-B3 J209-A4~A9 J209-B9 J209-B8 J102-B3 J102-A1~A7 J102-B8 J102-B2 IC101 DC controller PCB Figure 3-506 3–66 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 121 DC output voltage is main- cific timing (according to AGS measurement to tained to a specific value. increase the developing bias). 3–67 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 122: Controlling The Separation Static Eliminator Bias
Separation static eliminator bias drive circuit T101 drive circuit Q605 J209-B7 J209-A4~A9 J102-B4 J102-A1~A7 IC101 DC controller PCB Figure 3-507 3–68 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 123: Controlling The Transfer Guide/Fixing Roller Bias
Fixing Photosensitive drum assembly Composite power supply PCB T101 Transfer guide T101 drive circuit Q605 J209-A4~A9 J102-A4~A7 DC controller PCB IC101 Figure 3-508 3–69 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 125 Based on the results of the foregoing additions, the absence of toner is assumed for the following: • (T1 + T2) > 20 sec .....toner absent level 1 • (T1) or (T2) > 160 sec..toner absent level 2 3–71 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 126 Upon detection, the Waste Toner Case Full message will be indicated during standby. Waste toner sensor PS10 Waste toner feeding blade Main motor Cleaner housing Coupling Photo sensitive drum Figure 3-511 (conceptual diagram) 3–72 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 127: Primary Charging Roller Cleaning Mechanism
3. OPERATIONS AND TIMING H. Primary Charging Roller Cleaning Mechanism 1. Outline The GP215/GP200 is equipped with a mechanism which automatically cleans the primary charging roller. The primary charging roller cleaning solenoid (SL1) is turned ON while the primary charging roller is rotating to butt the cleaning pad against the primary charging roller while, at the same time, the primary charging roller is moved back and forth in the axial direction of the primary charging roller.
Page 128: Detecing Errors On The Composite Power Supply Pcb
As described later, errors which cause the scanning lamp are also checked by this detection mecha- nism. (Resetting the machine after such errors requires replacement of the scanning lamp.) LED100 Figure 3-513 DC Controller PCB 3–74 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 129 LED flashes at intervals of 6 sec, check to make sure that the inner side of the glass around the filament at both ends of the fluorescent lamp has not become black. 3–75 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 130: Pick-Up/Feeding System
VI. PICK-UP/FEEDING SYSTEM A. Outline The GP215/GP200 uses center reference, in which copy paper moves along the center of the pick- up/feeding assembly. The pick-up system consists of two cassettes (upper, lower) and the multifeeder. Copy paper from any of the cassettes or the multifeeder is controlled by the registration roller so that its leading edge matches the leading edge of the image on the photosensitive drum;...
Page 131 3. OPERATIONS AND TIMING Regiatration roller Photosensitive drum Feeding Multifeeder pick-up roller assembly Fixing assembly Vertical path roller Q1604 Q1605 Figure 3-601 Pick-Up/Feeding Assembly Sensors 3–77 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 132 Table 3-602 Pick-up/Feeding System Motors, Clutches, and Solenoids DC controller PCB Main motor driver PCB DFLD* J105-A5 J105 J103 Figure 3-602 Pick-Up/Feeding System Motors, Clutches, and Solenoids 3–78 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 133: Pick-Up From The Cassette
Note: Pulse signal so that it cannot be checked by a meter in reference to its state (0, 1). Table 3-603 List of Loads in the Cassette Pick-Up Assembly 3–79 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 134 Pick-up roller Lifter Separetion roller Pick-up roller Pick-up solenoid Feeding roller Lifter Separetion roller Figure 3-603 Conceptual Diagram of the Pick-Up Unit Drive Mechanism 3–80 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 135 Lower cassette paper level sensor 1 2RPD1 J108-4 *Jack in the signal line on the DC controller PCB. Table 3-604 Sensors on the Cassette Pick-Up PCB (pick-up unit) 3–81 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 136 Cassette pick-up PCB Lower cassette Figure 3-604 Sensors on the Cassette Pick-Up PCB Note: The sensor Q1603 is not used in the copier’s pick-up unit. 3–82 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 137: Basic Sequence Of Operations
(PS8) Registration roller paper sensor (PS5) Registration clutch (CL1) Scanner motor (M2) Main motor (M1) Figure 3-604 Sequence of Pick-UP Operations (cassette) 3–83 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 138 This movement frees the cam so that the cam starts to rotate. Feeding roller Pick-up roller Pick-up roller shaft Lifter trigger lever Figure 3-606 3–84 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 139 Lever Pick-up roller shaft Lever Pick-up roller Spring Spring Lifter Copy paper < Lifter up > < Lifter at Rest > Figure 3-608 3–85 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 140 Such a condition may not fully release the lifter so it is important to turn OFF and ON the main power to start standby state. Forcing the casstte out in such a condition can result in damage. 3–86 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 141 Gear 1 movement during CCW rotation Figure 3-609 Movement of Gear 1 in Relation to the CW/CCW Rotation of the Cassette Pick-Up Motor (M4) 3–87 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 142 Feeding roller Cassette pick-up roller (M4) Pick-up roller Separation roller Gear 1 Figure 3-611 Pick-Up Drive for the Lower Cassette (pick-up motor rotating CCW) 3–88 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 143 Pick-up lever The cam 1 rotates when SL2 turns ON. Cam 1 Pick-up solenoid (SL2) Figure 3-613 Up/Down Movement of the Pick-Up Roller Shaft 3–89 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 144 Q1604 : Upper cassette Q1605 : Lower cassette Paper detecting lever Figure 3-614 Arrangement of the Paper Detecting Lever 3–90 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 145: Non-Pick Up Operation (Standby)
Pick-up roller shaft Lifter trigger lever Figure 3-616 Moving Up the Lifter 3–91 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 146 Cassette Figure 3-618 Releasing the Separation Roller b. Releasing the Lifter The lifter is released when the cassette is slid out during standby. 3–92 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 147: Detecting The Level Of Copy Paper
Q1606 Gear when the cassette is full of (upper cassette) copy paper Figure 3-621 Detecting the Level of Paper inside the Cassette (upper) 3–93 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 148 Indication on control panel sheets sheets 1: The light-blocking plate is over the sensor. 0: The light-blocking plate is not over the sensor. Table 3-605 3–94 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 149: Detecting The Size Of Copy Paper
Figure 3-622 Location of the Dial inch Switch Figure 3-623 AB-/Inch-Configuration Switch 3–95 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 150 Set by user Set by user SP-4 Set by user Set by user ENV2 Set by user Set by user Table 3-606 Copy Sizes 3–96 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 151 An icon may be selected to represent the SPECIAL cassette for display on the control panel. For details, see the Operator’s Manual. 3–97 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 152 110 × 220 (mm) 162 × 229 (mm) 176 × 250 (mm) Table 3-607 Envelope Sizes COM10, Monarch, DL Figure 3-625 Shape of Envelope 3–98 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 153 (middle size cassette; for A5 through B4) Lower cassette (large size cassette; for A5 through A3) Figure 3-626 Upper/Lower Cassette Size Side guide plates Figure 3-627 Side Guide Plate 3–99 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 154: Multifeeder
Multifeeder tray Paper guide plate Separation pad Paper guide plate drive cam Spling clutch J114-B13 PRDSD* Multifeeder holding plate releasing solenoid Figure 3-627-1 3–100 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 155 The maximum size of copy paper is 432 × 279 mm (11” × 17”). Slide guide (rear) Variable resistor Multifeeder tray Slide guide (front) Figure 3-627-2 3–101 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 156 SCFW Multifeeder relay releasing solenoid (SL3) Multifeeder pick-up clutch (CL2) Pre-registration roller sensor (PS5) Registration roller clutch (CL1) Main motor (M1) Figure 3-627-3 3–102 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 157: Controlling The Registration Roller Clutch
Image area when copying on 2nd side D area: Erased by blank exposure lamp Drum Drum Image on drum Image on drum Copy paper ahead Copy paper behind of image on drum image on drum 3–103 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 159 Lower feeding assembly inlet sensor PS12 PDP6* J105-B2 Delivery sensor PS13 PDP7* J105-A2 Jack in the signal line on the DC controller PCB. Table 3-608 3–105 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 160: Making Two-Sided Copies
Re-pick up roller Set-back rollers Flow of copy paper Flow of copy paper Details of the movement of the paper deflecting plate Figure 3-629 3–106 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 161 *1 : Copy paper is moved to the lower feeding assembly. *2 : Copy paper is moved to the delivery assembly. Figure 3-630 3–107 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 162: Lower Feeding Assembly
Lower feeding assembly re-pick up clutch Table 3-610 Names of Electrical Parts DC controller PCB PS11 PS12 Set-back rollers Re-pick up roller Lower feeding assembly Figure 3-631 3–108 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 163 Inch ; 11 × 17, LGL, B-OFFI, A-OFFI, A-LGL, AUS-FLS, FOOLSCAP, FOLIO, G-LGL, E-DFFI, OFFICIO, A-LTRR, LTRR, K-LGLR, G-LTTR, A-LTR, STMTR Table 3-611 Accommodating Paper in the Lower Feeding Assembly 3–109 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 164 3) If the copy paper is A4 or larger, SL4 operates the flapper to prevent the copy paper from moving to the re-pick up roller. Copy paper PS12 PS11 Flapper Re-pick up roller Set-back rollers 3–110 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 165 By repeating the above operations, as many as 20 sheets of copy paper are stacked in the lower feed- ing assembly (i.e., 20 sheets of LTR, A4, G-LTR, K-LGL, B5, A5, or STMT). 3–111 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 166 Re-pick up front paper sensor (PS11) Main motor (M1) *1 : Varies according to the length of copy paper. Figure 3-632 (A4, 2 copies, Direct, two-sided/overlay) 3–112 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 169 The paper edge position differs depending on copy paper size, making SP different. Home position of the horizontal registration sensor. Detection start position of the horizontal sensor. Figure 3-635 3–115 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 170 Lower feeding assembly re-pick up clutch Re-pick up paper deflecting solenoid Vertical path sensor PS11 Re-pick up sensor PS14 Horizontal registration sensor Table 3-612 3–116 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 171 • If the image is displaced to the front, increase the value. Specific distance Image area Copy paper Edge Virtual home position Value increased Figure 3-638 3–117 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 172: Fixing/Delivery Assembly
Main thermistor (TH1) Fixing heater drive circuit Relay drive signal Relay Fixing heater drive signal (HTRD) Zero cross signal Composite power supply PCB Figure 3-639 3–118 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 173 6th to 10th copy 21st to 30th copy 11st to 15th copy 31st to 40th copy 235˚C 230˚C 225˚C 215˚C 210˚C 205˚C 140˚C 100˚C Figure 3-640 3–119 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 174 3; if offset continues, change it to 4. 1st to 30th copy 195°C 31st to 40th copy 190°C 41st to 50th copy 185°C 51st to 100th copy 180°C 3–120 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 175 (through phase control). Zero cross signal Fixing heater drive signal Supply power to fixing heater Heater OFF Power applied to heater Figure 3-641 3–121 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 176 (HTRD) remains OFF is moni- tored; if an error is detected, the power is turned OFF. (E004 will be registered.) 3–122 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 177 Main motor driver PCB Tension roller Fixing film Main motor Fixing film sensor (PS2) Delivery Drive roller Fixing heater Lower roller Figure 3-642 3–123 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 178 Figure 3-643 Tension roller Drive roller Displaced to the front Displaced to the rear Normal ON Figure 3-645 To rear To front Figure 3-644 3–124 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 179 The fixing film motor is a stepping motor rotated by pulse signals A, A*, B, B*. DC controller PCB +24V 109-8 109-9 109-10 A 109-11 A* 109-12 B 109-13 B* Figure 3-646 3–125 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 181: Delivery Assembly
Paper deflecting plate 1 solenoid Fixing rear paper sensor PS12 Lower feeding assembly inlet paper sensor PS13 Delivery sensor PS13 Table 3-613 Electrical Parts PS12 Figure 3-650 3–127 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 182 SL5 OFF PS13 PS12 Copy paper PS12 Figure 3-651 Paper Deflecting Plate 1 Solenoid ON Figure 3-652 Paper Deflecting Plate 1 Solenoid OFF 3–128 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 183 Feeding copy paper from the fixing assembly to the lower feeding assembly Figure 3-654 Movement of the Paper Deflecting Plate 1 3–129 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 184: Detecting Jams
PDP 6* J105-B2 PS13 Delivery assembly paper sensor PDP 7* J105-A2 *Jack in the signal line on the DC controller PCB. Table 3-614 3–130 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 185 Jam check Vertical path paper Normal Error sensor (PS8) Cassette pick-up motor (M4) Main motor (M1) Figure 3-656 Sequence for Pick-Up Delay Jams 3–131 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 186 Pick-up of 2nd copy Jam message INTR Multiple pick-up clutch (CL2) Pre-registration sensor jam check Pre-registration Normal Error sensor (PS5) Main motor (M1) Figure 3-657 3–132 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 187 Registration roller clutch (CL1) Separation sensor jam check Separation sensor Normal Error (PS5) Main motor (M1) Figure 3-659 Sequence for Separation Sensor Delay Jams 3–133 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 188 SCRV SCFW SCRV LSTR Delivery sensor jam check Delivery sensor Normal Error (PS13) Main motor (M1) Figure 3-661 Sequence for Delivery Delay Jams 3–134 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 189 Note 1 : The distance varies according to the length of copy paper. Figure 3-662 Sequence for Delivery Sensor Stationary Jams Note: The distance varies according to the length of copy paper. 3–135 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 190 Lower feeding assembly Normal Error inlet sensor (PS12) Main motor (M1) Figure 3-664 Sequence for Lower Feeding Assembly Inlet Delay Jams (two-sided copying) 3–136 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 191 Re-pick up paper sensor jam check Re-pick up sensor Normal (PS11) Main motor (M1) Figure 3-666 Sequence for Re-Pick Up Delay Jams (error) 3–137 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 192: Jam History
If the message “Return Original and Press Start” appears on the control panel after removing the jam, put the original back into the feeder as they were set initially. 3–138 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 193: Fans
Exhausts heat from the electrical unit. Lower feeding assembly Blowing Cooling copy paper in the lower feeding unit cooling fan Table 3-701 Figure 3-701 3–139 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 194 An original is placed in the feeder, or The copyboard cover or the feeder is opened. Varies depending on the setting for quiet mode. Figure 3-702 3–140 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 195: Power Supply
DC controller PCB (white areas in Figure 3-802) are supplied with power. In this mode, FAX and printer functions are enabled. 3–141 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 196 DC controller PCB DC+24Vu,DC+24VR DC+15V,DC-12V,DC+5V DC loads · ADF · Multi Output Tray-C1 · Pedestal · Sensor · Clutch · Solenoid Figure 3-801 3–142 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 197 · ADF · Multi Output Tray-C1 · Pedestal · Sensor · Clutch · Solenoid *Power is not supplied to shaded units. Figure 3-802 3–143 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 198 · ADF · Multi Output Tray-C1 · Pedestal · Sensor · Clutch · Solenoid *Power is not supplied to shaded units. Figure 3-803 3–144 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 199: Sleep Mode
Retained by SLEEP 1 enabled: e.g., fax power supply transmission, fax Operates reception, printing. All functions are avail- Standby Operates able. Table 3-802 3–145 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 200 · Composite power supply PCB CPU : ON · Image processor PCB CPU : OFF FAX reception. · LCD : OFF Figure 3-804 3–146 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 201 SLEEP 1 provides an anti-condensation function for areas around the scanner system, but SLEEP 2 does not have this function. Top: SLEEP 1 Bottom: SLEEP 2 SLEEP 1 SLEEP 2 3–147 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 202: System
: Print paper for printer image • System Motherboard** * Included in the Extension Kit A1. ** Included in the Extension Kit B2. Conceptual Diagram of Non-Stop Copying 3–148 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 203 Originsl tray Scanner (moving) Reversal for face-down delivery • Picking Up Originals for Fax Transmission Originals (face up) RDF-G1 Scanner (moving) Original delivery tray 3–149 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 204: Diagram Of The Function Boards
Image processor Network Interface Board CIST J510 J503 J504 J508 J509 Protocol controller Scanner Board J505 J200 J201 J501 J502 System Motherboard Printer Board 3–150 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 205 • FAX Motherboard circuit assembly • FAX Board Video signal switching circiut • System Motherboard • Printer • Etc. SCSI Board Fig. 3-905 3–151 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 206 The Protocol Controller PCB converts printer commands from a personal computer to control the print- er system of the GP215/GP200 to support GP215/GP200-specific multiple cassette functions not found in a configuration consisting of a Multi Device Controller and a GP55/GP30F.
Page 207 3. OPERATIONS AND TIMING c. Scanner Board The Scanner Board reads images read by the GP215/GP200 for transmission to the host computer through a SCSI interface, and it has the following specifications: Interface SCSI- A3; 297 × 420 mm/11”×17” 279×432mm...
Page 208: Flow Of Image Signals
Protocol Controller Board memory Rotation Memory Command CIST conversion Memory Smoothing CORE/IP Board SCSI Video control controller controller Host controller computer Printer Board Host computer 3–154 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 209 Protocol Controller Board memory Command Rotation memory CIST conversion Memory SCSI CORE/IP Board controller Video controller controller Host computer controller Printer Board Host computer 3–155 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 210 Protocol Controller Board memory Command Rotation memory CIST conversion Memory SCSI CORE/IP Board controller Video controller controller Host computer controller Printer Board Host computer 3–156 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 211 Protocol Controller Board memory Rotation Command CIST memory conversion Memory Smoothing CORE/IP Board SCSI Video controller controller controller Host computer controller Printer Board Host computer 3–157 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 212: Service Mode
• Indicates items for options, allowing changes to the set- tings. *8* FAX Fax Service Mode • Indicates items to be set/changed or operated for fax func- tions from the screen. 3–158 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 213: Using Service Mode
3) Press the service switch with a hex key. • ‘$’ will appear in the upper left corner of the LCD, indicating that the machine has start- ed service mode. 3–159 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 214: Using Adjustment Mode And Settings Mode
ATVC OFST attached to the image proces- FL OFST sor PCB) DDC OFST Figure 3-1005 (Service Label; attached to the composite power supply PCB) 3–160 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 215: Display (Control Display Mode)
Unit: °C (output of thermistor TH1) SUB_TH Indicates the temperature at the end of the fixing assembly. (out- Unit: °C put of thermistor TH2) 3–161 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 216 1st cassette jam code (pre-registration sensor delay jam) time of recovery (14:35) time of occurrence (14:30) date of occurrence (August 21) 3–162 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 217 See p. 7-51. Pick-Up Location Codes Code Pick-up location Cassette 1 Cassette 2 Cassette 3 Cassette 4 Cassette 5 Cassette 6 Multifeeder Two-sided/overlay re-pick up 3–163 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 218 1063 Door Front door Right door Pedestal right door Low- order High- Type code order of jam code Door open 1101 1102 1103 3–164 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 219 Upper cover opened during operation 0083 Original circulation fault 0084 Original left behind 0088 Original left behind on copyboard glass 0089 Re-circulating lever fault 3–165 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 220 BODY Refers to the copier. Refers to the feeder (ADF/RDF). Refers to the sorter. • Copier-Related Alarm Code Description Replace the drum unit. 3–166 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 221 STMTR, LTR), but the detected original is not the last original. Note: The number in parentheses under the Code column is in decimal notation. 3–167 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 222 1500 ms feeding roller, and pick-up roller stop after pick-up. immediately. The RDF stops after delivering the copy of the advance orig- inal. 3–168 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 224 (M4), or stapler swing motor (M5); the same type of error has occurred after turning off and on the power. 3–170 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 225 Staple The stapler has Prohibits sta- Indicates the Replace the sta- absent run out of staples. pling. Add Staple mes- ple cartridge. sage. 3–171 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 226 ENGLISH NORWEGIAN FRENCH PORTUGUESE GERMAN SPANISH DANISH SWEDISH DUTCH POWER_C Indicates the version number of the CPU on the composite power supply PCB. 3–172 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 227 Indicates the version number of the Network Interface Board (NIB). PS/PCL Indicates the version number of the Printer Board (PS/PCL). SCSI Indicates the version number of the SCSI Board. 3–173 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 229 Keypad 2 Keypad 3 Keypad 4 Keypad 5 Keypad 6 Keypad 7 Keypad 8 Keypad 9 Start Stop Clear Interrupt Guide User Mode 3–175 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 230 11: little (about 10 mm high) 01: little/absent CST-1 Cassette 1 CST-2 Cassette 2 CST-3 Cassette 3 CST-4 Cassette 4 CST-5 Cassette 5 CST-6 Cassette 6 3–176 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 231 00110 U4 G-LTR 00111 U5 G-LTRR 00011 U6 G-LGL 01011 U7 K-LGL 01010 U8 K-LGLR 01000 SPECAL1 01101 SPECAL2 01100 Envelope 2 01110 3–177 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 232: 2* I/O Display (I/O Display Mode)
0: connected CCF connect 0: connected PCB internal signal power saving mode switch 0: ON Not used. main power switch 0: ON 3–178 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 233 PCB internal signal (output) PCB internal signal PCB internal signal PCB internal signal PCB internal signal PCB internal signal PCB internal signal PCB internal signal 3–179 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 234 PAD OFF for editing board power SW1 laser control area signal switching 1: w/ editing board installed Not used.. Post ratio change reversal switching 3–180 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 235 — — CSZ10 J110-2 (input) CSZ11 J110-3 CSZ12 J110-4 CSZ13 J110-5 CSZ14 J110-6 CSZ20 J110-8 CSZ21 J110-9 CSZ22 J110-10 CSZ23 J110-11 CSZ24 J110-12 3–181 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 236 J115-6 feeding fan drive FFMD J107-A8 exhaust fan 1 drive J107-A9 laser cooling fan drive J113-B3 PCB internal signal — — 3–182 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 237 Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. 3–183 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 238 (PCB internal signal) exhaust fan 2 drive J107-B1 exhaust fan half-speed (PCB internal signal) Not used. Not used. Not used. Not used. Not used. 3–184 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 239 UCRMN J122-1 LCRMN upper cassette paper detection LCRMN J122-2 lower cassette paper detection J122-3 lower cassette paper detection J122-4 Not used. Not used. 3–185 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 240 4. Gate Array Input/Output of the DC Controller PCB *2* I/O DISPLAY 04 CANCEL ICSW2 : xxxxxxxxxxxxxxxx ICSW4 : xxxxxxxxxxxxxxxx ICSW5 : xxxxxxxxxxxxxxxx ICSW15 : xxxxxxxxxxxxxxxx ICSW25 : xxxxxxxxxxxxxxxx – 3–186 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 241 (Indicated when DF P0 : xxxxxxxx an ADF is DF ExPA : xxxxxxxx connected.) DF ExPB : xxxxxxxx DF ExPO : xxxxxxxx – 3–187 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 242 Not used. DFP9 copier communication signal copier communication signal copier communication signal Not used. copier communication signal Not used. Not used. Not used. 3–188 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 245 1 DLDL J5-2 (PI9) original length detection 1 DLDM J5-3 OPI8) original length detection 1 DLDS J5-4 (PI7) PCB internal signal 3–191 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 246 Not used DF-AD1 Not used DF-AD2 Not used DF-AD3 Not used DF-AD4 Not used DF-AD5 Not used DF-DA0 Not used DF-DA1 Not used 3–192 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 247 *2* I/O DISPLAY 07 CANCEL ST-A : xxxxxxxx ST-B : xxxxxxxx ST-C : xxxxxxxx ST-EX-A : xxxxxxxx ST-EX-B : xxxxxxxx ST-EX-C : xxxxxxxx – 3–193 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 248 GBHP J4-6 1: At HP. Stapler HP sensor (MS4) SPUHP J17-3 1: At HP. Stapling HP sensor (MS7) SPLHP J7-8 1: At HP. 3–194 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 249 1: Paper detected. (PI9) Tray A delivery detection (PI8) J11-8 1: Paper detected. Tray feeding assembly inlet slot TFPD J11-5 1: Paper detected. sensor (PI7) 3–195 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 250 0: Key ON. ST-AD5 Push SW (SW2) 0: SW2 pressed. ST-AD6 Push SW (SW1) 0: SW1 pressed. ST-AD7 Staple absent 1: Staple absent. 3–196 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 251: 3* Adjust (Adjustment Mode)
2-15. (210mm) value of the multifeeder paper width sensor. MF-A4 MF-A4: Indicates the stored A4 (297mm) value of the multifeeder paper width sensor. 3–197 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 252 Indicates the primary charging AC out- (IMG) put while an image is exposed. PRI AC Indicates the primary charging AC out- (no IMG) put between sheets. 3–198 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 253 Indicates scanning lamp offset. DDC OFST DEV DC Indicates developing bias DC compo- OFST nent offset. * Service Label; attached to the composite power supply PCB. 3–199 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 254 A higher setting delays the registration ON timing. RESIST Use it to adjust the registration clutch ON 0~1000 Standard: timing (leading edge margin). 2.5 ±1.0 mm 3–200 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 255 Use it to correct offset from the laser center. • If you have initialized the RAM or –200~+200 replaced the image processor PCB, enter the value recorded on the service label. 3–201 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 256 Use it to adjust arching (cassette pick-up; 0~65535 for factory use). MF-LOOP Use it to adjust arching (multifeeder pick-up; 0~65535 for factory use). 3–202 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 257 ––> Enter under ‘PWM600MAX’. PWM 200 MAX the label attached ––> Enter under ‘PWM20MIN’. to the image ––> Enter under ‘PWM200MAX’. processor PCB. 3–203 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 259 Use it to increase the setting if the text den- Service handbook sity is too low (light image) when executing 0~40 p.2-21. AE mode with priority on image quality. 3–205 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 260 Indicates the standard white plate data image processor (density data of the standard white plate). PCB, be sure to 0~65535 enter the value recorded on the service label. 3–206 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 261 Settings are between 0 and 10; however, a value higher than 10 may be entered. (Any such number will be treated as ‘5’ for control.) 3–207 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 262: 4* Function (Function Mode)
To clear an error indication, press ‘ERROR’ on the E004, E007-01, or E717 screen to highlight; then, press the OK key, and turn OFF/ON the main power switch. 3–208 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 263 At the same time, ‘TONER_S’ [240] (in sec) starts to increment; the operation stops at [0]. To stop in the middle, press ‘STOP’ to highlight, and press the OK key to stop. 3–209 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 264 WB xxxxH WP xxxxH LAMP xxxxH GDA1 xxH GDA2 xxH CDA3 CDA4 xxH ADDA5 xxH Results of measurement D-ODD xxH D-EVN xxH under each item – 3–210 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 265 4) Check the values under A, B, and D: 20≤A≤50 –40≤B≤40 0≤D≤8 5) If the values are as indicated, press ‘DAT SET’ to highlight, and press the OK key. 3–211 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 266 4) Check the value of A, B, and D. Insert 5) If the values are as indicated, press ‘DATA SET’ to highlight, and press the OK key. 3–212 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 267 4) Check the value of A, B, and D. Insert 5) If the values are as indicated, press ‘DATA SET’ to highlight, and press the OK key. 3–213 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 268 • The value will be stored under ‘A4’. 7) Press the Reset key twice to end service mode. 8) Turn off and then on the main power switch. 3–214 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 269 • The LEDs on the control panel will turn on. 3) Press the OK key. • The LEDs on the control panel will turn off. 3–215 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 270 • The laser scanner motor will start to rotate. 2) Press ‘OFF’ to highlight; then, press the OK key • stopping operation to stop the laser scanner motor. 3–216 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 271 L-TEST2: halftone test print L-TEST3: blank test print L-TEST4: 17-gradation test print L-TEST5: grid test print L-TEST6: vertical line test print L-TEST7: horizontal line test print 3–217 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 272 • If uneven density (left/right) is noted, sus- pect dirt on the primary charging roller or a fault in the developing system. 3–218 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 273 • Use it to check straight lines. • If a discrepancy is noted, suspect a dis- placed laser beam or a fault in beam detec- tion. 3–219 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 274 2) Press the OK key to start a check on the image processor PCB. • ‘OK’ or ‘NG’ will be indicated; if ‘NG’, replace the image processor PCB. 3–220 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 275 WB xxxxH WP xxxxH LAMP xxxxH GDA1 xxH GDA2 xxH CDA3 CDA4 xxH ADDA5 xxH Results of measurement D-ODD xxH D-EVN xxH for each item – 3–221 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 276 • The following screen will appear to indicate that the system is ready to accept downloading: IP FDIMM download program 3) Operate according to the instructions on the PC screen. 3–222 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 277 Indicates the position of the rear end of the fixing film from the V-cut. LEVEL Indicates the position of the fixing film (4 or 5 is opti- mum). 3–223 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 278 ‘OPTION’ in service mode (*5*) to ‘0’ so that the measurement may be used as a reference. • For a guide, see the diagram below. SELECT_GAMMA_NUL setting -28.0µA AGS_MEASURE setting -36.5µA -43.0µA 3–224 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 279 Use this mode to collectively reset the jam histories shown under ‘DISPLAY’ in service mode (*1*). Press ‘JAM_RLS’ to highlight; then, press the OK key. 3–225 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 280 ALL: Select it to collectively initialize the above data. (Executing this item will initialize the back-up data of both fax and copier.) 3–226 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 281 *6*; however, the machine must *3*: ADJUST be installed with a FAX Board. *5*: OPTION *6*: COUNTER The machine must be equipped with fax functions. 3–227 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 282 “Replace Drum” message. sage on the control panel. (default in 230V model) 1: Will indicate the Replace Drum message. (default in 120V model) 3–228 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 283 However, if such a problem occurs, you must suspect a fault in the image processor PCB, DC controller PCB, or composite power supply PCB. 3–229 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 284 1: The bottommost page of the stack of origi- nals will be picked up and read first and returned to the original tray (same way as copying). 3–230 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 285 2: ‘OFI’, standing for Ecuadorian OFICIO. 5:A-OFI 3: ‘LGL’, standing for Argentine LEGAL. 4: ‘OFFI’, standing for Bolivian OFICIO. 5: ‘OFFI’, standing for Argentine OFICIO. 3–231 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 286 CST-U7 cated: CST-U8 Paper Notation U2: FOLIO ..FOLIO U3: A-FLS...FLS U4: G-LTR...LTR U5: G-LTRR ..LTRR U6: G-LGL ..LGL U7: K-LGL...LGL U8: K-LGLR ..LGLR 3–232 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 287 LTRR-size cassette. 1: If the paper size dial of the cassette is set to LTRR, ‘LTRR’ will be indicated to stand for Argentine LETTER-R. 3–233 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 288: 6* Counter (Counter Mode)
Indicates the large-size copy count from the cassette 4. L_CAST5 Indicates the large-size copy count from the cassette 5. L_CAST6 Indicates the large-size copy count from the cassette 6. 3–234 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 289 Indicates the small-size copy counter from the cassette 4 S_CAST5 Indicates the small-size copy counter from the cassette 5. S_CAST6 Indicates the small-size copy counter from the cassette 6. 3–235 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 290 Indicates the small-size copy count. FAX_S_PRINT Indicates the small-size copy count. PDL_S_PRINT Indicates the small-size printer print count. ETC_S_PRINT Indicates the small-size print count by other system. 3–236 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 291 Indicates the scan count for printer mode. ETC_SCAN Indicates the scan count for other system. PRINT_JAM Indicates the print jam count. DH_JAM Indicates the feeder jam count. 3–237 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 292: 7* Acc (Accessory Mode)
P_INTRVL_B Use it to adjust the origi- nal stop position for lower separation pick-up in 2-on- 1 mode. 3–238 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 293 ‘DOC-STP-T’ and ‘P_INTRVL_T’, the sheet will be discharged to the RF’s original delivery tray.) 8) To end the work, press the Reset key twice to leave service mode. 3–239 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 294 6 of DIPS1 on the RF controller PCB. S_BCLN_B Use it to clean the separa- tion belt for lower separa- tion. 3–240 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 295 A higher setting increases the feeding speed, nal feeding speed. contracting the image in feeding direction. A lower setting decreases the feeding speed, extending the image in feeding direction. 3–241 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 296: Electrical System
‘200PWM density auto correction’, and ‘600PWM density auto cor- rection’ in service mode. 7) Enter settings/values under ‘OPTION’ (*5*) and in user mode. 3–242 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 297 *4* FILM_INIT_ROTATE ing assembly under ‘FIXER- REGST’ and in ser- vice mode (*3*). 2) Execute ‘FILM_INIT_ROTATE’ (14th page under ‘FUCTION’; *4*). 3–243 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 298 • ‘shading auto correction’ will be executed. 8) In a while, ‘Now [END]’ will appear on the screen to indicate the end of shading correc- tion. 3–244 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 299 3) Press the service switch with a hex key. – • ‘$’ will appear in the upper left corner of the LCD. Figure 3-1011 3–245 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 300 • Scanning lamp • Laser unit • Composite power supply PCB • Analog processor PCB Printed side down • Image processor PCB Figure 3-1013 3–246 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 301 • The value will be stored under ‘MF-A6R’. 10) Likewise, set A4R paper in the multifeeder, and adjust the side guide to A4R. 3–247 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 302 (FY9-3004) on the copyboard glass. • ‘$’ will be indicated in the upper left corner of the LCD. Copy paper Copyboard glass Figure 3-1019 3–248 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 303 – Figure 3-1020 10) In a while, ‘Now [END]’ will appear on the screen, indicating the end of shading auto correction. Figure 3-1021 3–249 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 304 Figure 3-1023 3) Install the removed covers, and connect the power cord into the power outlet; then, turn on the main power switch. 3–250 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 305 • When the machine boots up, it will show the following screen to indicate that it is in downloading mode: 3–251 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 306 (factory default: 3) The adjustment will modify the density correction curve. Copy density White Higher setting Lower setting Black Original density Black White Figure 3-1026 3–252 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 307 'ADJUST' in setting AE table service mode (*3*). Higher setting Black Black Light Light Dark Dark Input Input (white) (white) (black) (black) Figure 3-1027 3–253 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 308 Display reading — — Tester reading about 5 V about 0 V about 5 V about 0 V about 5 V about 0 V 3–254 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 309 Display reading — Tester reading about 5 V about 0 V about 5 V about 0 V about 5 V about 0 V 3–255 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 311 • If the machine is not equipped with the FAX Board, try replacing the FAX Motherboard, CORE/IP Board, Protocol Controller PCB, System Mother Board, and the Printer Board. 3–257 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 312 Service Manual. Try replacing the FAC Suspect a fault in the party Motherboard and the or the line. CORE/IP Board, which affect printer images. 3–258 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 313 Font Font Font DRAM DRAM DRAM Note: Printer settings determine whether printing will be subject to type of resolution (600/400/300 dpi) and CIST processing. 3–259 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU...
Page 315: Self Diagnosis
135°C for 200 ms 1 sec after it has detected 120°C. • The main thermistor (TH1) detects less than 150°C for 200 ms 1 sec after it has detected 135°C. 3–261 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 316 • Horizontal registration sensor drive signal. (PS14; faulty) • Horizontal registration motor (M9; faulty) • DC controller PCB (faulty) 3–262 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 317 DC controller PCB has nication between the DC controller PCB occurred. an the image processing PCB. • DC controller PCB (faulty) • Image processor PCB (faulty) 3–263 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 318 PCB has an error. power supply PCB. Both ends of the fluorescent lamp has blackened because of deterio- ration. 3–264 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 319 After the film has returned to normal position following the execution of 'FILM COMEBACK', be sure to turn OFF and then ON the main power supply without touching the other keys. 3–265 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 320: Self Diagnosis Of The Rdf-G1
2. You may continue to make copies even when the RDF is out of order; open the RDF, and place originals on the copyboard glass. 3–266 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 321: Self Diagnosis Of The Pedestal
The shift tray home position sen- • The home position detection signal does E422 sor fails. not turn on within 5 sec during shift tray home position search. 3–267 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 322: Self Diagnosis Of The Multi Output Tray-12
2.5 sec or more after the guide bar swing motor drive signal has been generated. 3–268 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 323 *Turn off the joint sensor (MS3; feeding the multitray from the copier); you need not disconnect the communication connector connecting to the copier. 3–269 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 325 E. Pick-Up Drive Assembly ....4-15 Composite Power Supply PCB..4-37 PICK-UP ASSEMBLY ......4-18 C. Replacing the ROM DIMM A. Pick-Up Assembly ......4-18 (image processor PCB) ....4-38 Multifeeder Assembly .....4-20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 327: Chapter 4 Mechanical System
Control panel power switch e Main power lamp w Main power switch r MEMORY TX/RX lamp * For USA, ‘PRIN·I/F’ Figure 4-101 4–1 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 328: Handling The Harnesses
4. MECHANICAL SYSTEM B. Handling the Harnesses Exercise care when using the harness retainer (square bush) to avoid biting the harnesses. NO GOOD Figure 4-102 4–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 329: Externals
Rear cover r Delivery assembly cover w Upper rear cover t Delivery tray e Left cover y Delivery assembly lower cover Figure 4-202 4–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 330: Inside Cover
7) Remove the four screws e, and remove the right cover r. Figure 4-206 2) Remove the screw r, and remove the fixing cover e. Figure 4-205 Figure 4-207 4–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 331: Inside Cover
5) Release the feeding assembly, and remove the feeding lever u (1 top ring i) and the registration roller knob o. Figure 4-209 4–5 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 332: Control Panel
PCB q. and turning over the control panel. Figure 4-211 Figure 4-212 6) Disconnect the four connectors. 4–6 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 333: Fans
3) Disconnect the two connectors q, remove the two screws w, and disengage the three hooks e to remove the fixing heat exhaust fan. Figure 4-214 Figure 4-213 4–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 334: Drive Assembly
Figure 4-302 3) Remove the two screws e, and release the cable spring stay w (front, rear). Figure 4-301 Figure 4-303 4–8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 335 4. MECHANICAL SYSTEM 4) Loosen the set screw r, and remove the cable (front, rear). Figure 4-304 4–9 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 336: Routing The Scanner Cable
6times Pulley clip toward the outside; then, snap on Set the mirror positioning the pulley clip. tool. Steel ball 32±1mm Figure 4-305 4–10 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 337 <Rear> <Front> Figure 4-308 Note: The pin A of the mirror positioning tool (FY9-3009-040) will not be used for the machine. 4–11 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 338 For rear No.1 mirror mount For front No.2/No3 mirror mount Figure 4-309 4) Tighten the set screw of the pulley. 5) Remove the tool. 4–12 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 339: Fixing Drive Assembly
Figure 4-311 7) Remove the seven screws u, and remove the fixing drive assembly y. Figure 4-310 Figure 4-312 4–13 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 341: Pick-Up Drive Assembly
4) Remove the harness retainer w, two high- Figure 4-315 voltage cable e, and power supply cord mount r (2 screws). Figure 4-317 4–15 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 343 (3 screws). 2) Remove the two screws w, and disconnect the connector e; then, remove the multi clutch. Figure 4-322 Figure 4-324 4–17 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 344: Pick-Up Assembly
1) Holding the knob assembly, push it in until a click is heard. 6) Remove the four screws u, and remove the pick-up assembly y. Figure 4-402 4–18 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 346: Multifeeder Assembly
3) Remove the multifeeder assembly. Reference: When installing the multifeeder connector cover, match the top first and push the bot- tom in. Figure 4-410 4–20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 347: Feeding Assembly
Figure 4-411 4) Remove the separation pad retaining plate e by releasing the hook r. Figure 4-413 Figure 4-412 4–21 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 348 7) Release the hook assembly i of the feeding fan cover u with a small flat-blade screwdriver. 8) Remove the feeding fan o. Figure 4-414 Figure 4-416 4–22 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 349: Lower Feeding Assembly
4) Remove the three screws e, and remove the lower feeding assembly. 5) Disconnect the connector of the lower feeding assembly, and remove the lower feeding assembly. Figure 4-419 Figure 4-418 4–23 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 350: Delivery Assembly
4) Remove the transfer guide unit. 5) Remove the registration roller. Figure 4-421 4) Disengage the hook e of the delivery assem- bly lower cover w. Figure 4-422 4–24 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 351 Figure 4-423 Figure 4-425 5) Move the delivery assembly to the right, and disengage its left and then its right to remove. 4–25 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 352 4) Loosen the adjusting screw to adjust so that the gap between the steel core E-ring and the solenoid frame is about 0.2 mm. 5) Install the delivery assembly to end the adjustment. 0.2mm Paper deflecting plate 1 solenoid Figure 4-426 4–26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 353: Exposure
7) Remove the screw, and remove the fluores- cent lamp cover r; then, pull out the scan- ning lamp. Figure 4-501 Figure 4-504 4–27 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 354: Ccd Unit
R&D and factory) 4) Remove the screw, and remove the original size sensor w to keep it away from the CCD unit. Figure 4-507 4–28 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 355: Ipu Pcb
Figure 4-508 Caution: Do not remove any paint-locked screws. Particularly, never remove the screw y. Figure 4-510 Figure 4-509 4–29 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 356: Laser Scanner Assembly
2) Remove the copyboard glass, CCD unit cover, IP cover, and IP PCB. 3) Remove the fan duct 2 q by sliding it to the rear. 4–30 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 357 1) Remove the laser scanner unit. laser scanner unit u. 2) Remove the two M3 screws w, and remove the laser driver unit q. Figure 4-516 Figure 4-514 4–31 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 358: Developing System
3. The gap between the cylinder and the blade is adjusted at the factory to high precision. Do not try to adjust it in the field. Figure 4-603 4–32 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 359 3; then, remove the developing assembly cover 1. Figure 4-604 2) Remove the two screws, and remove the blade mount 4. Figure 4-605 4–33 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 360: Fixing System
Figure 4-701 4) Turn the separation claw so that the boss t matches the bushing y. Figure 4-704 Figure 4-702 4–34 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 361 1) Slide out the fixing unit. 2) Push the hook assembly q, and slide the upper fixing guide w to the rear to remove. Figure 4-708 Figure 4-706 4–35 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 362 (electrode side) Fixing lower roller end Figure 4-710 5) Remove the two locking springs u. Figure 4-713 (front of shaft end) Figure 4-711 4–36 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 363: Electrical System
3) Remove the two screws q, and disconnect all power supply PCB. connectors; then, remove the DC controller PCB w. Figure 4-801 Figure 4-802 4–37 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 364: Replacing The Rom Dimm
PCB t; then, remove the four screws and the two flat cables, and remove the CPU PCB y. Figure 4-805 Figure 4-804 4–38 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 365 Figure 4-807 3) Install the covers that have been removed, connect the power cord to the power outlet, and turn ON the main switch. 4–39 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 367 Installing the Drum Cartridge ..5-10 III. RELOCATING THE MACHINE....5-30 E. Installing the Cassettes ....5-14 INSTALLING THE CONTROL CARD V ...5-31 Installing the Feeder .......5-16 COPY DATA CONTROLLER-A1....5-34 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 369: Selecting The Site
(See the next page.) g. The terminal of the telephone line is a modular type. • Otherwise, you need to convert it into a modular type. 5–1 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 370 6.5 cm 170 cm min. 180 cm min. 6.5 cm 170 cm min. 210 cm min. 6.5 cm 170 cm min. 200 cm min. 5–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 371: Unpacking And Installation
If the copier has been just moved from a cold place, leave it alone at least for one hour without unpack- ing it so that it will become used to the site temperature. 5–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 372: Unpacking
Remove the scanner fixing screw from the outside of the lifter cover. Scanner fixing screw Slide out the cassette, and remove the packing from inside. 5–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 373 Screw installation of the drum unit. Pull the dummy drum straight out to the front to remove. • Dispose of the dummy drum. 5–5 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 374: Supplying Toner
While holding the toner cartridge, pull out the opening knob to the front until it stops. 5–6 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 375 Turn the developing assembly locking lever in the direction of the arrow to lock the developing assembly in place. Developing assembly locking lever 5–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 376: Stirring The Toner
Connect the power plug to the The power outlet must be rated as specified. power outlet. Turn on the main power switch. Main power switch 5–8 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 377 The toner stirring operation takes 240 sec (4 min), and • Toner stirring starts. the operation will stop automatically. • Install the copy tray while the toner is being stirred. 5–9 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 378: Installing The Drum Cartridge
Remove the dust-proofing glass, and clean it with lint-free paper; Dust-proofing glass thereafter, put the dust-proofing glass back into its original posi- tion. 5–10 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 379: Drum Unit
Rail then, without removing the drum cover, insert the drum unit slowly along the rail. Drum unit Drum unit Drum cover 5–11 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 380 Check to make sure that the developing assembly is released; Rail Rail insert the drum unit slowly along the rail. Drum unit 5–12 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 381 • Lock the feeding assembly in place. Developing assembly releasing lever Feeding assembly releasing lever 5–13 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 382: Installing The Cassettes
Note: The label may be for A/B- or Inch-configuration. Be sure the correct label is used. Boss 5–14 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 383: Paper Size
• Keep in mind that the middle cassette will not hold paper A3 or 11×17 in size. Put coy paper. 5–15 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 384: Installing The Feeder
Stamp assembly Do not touch the face of the stamp. If your hands become stained with ink, wash them immediately. Protection sheet 5–16 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 385 Original tray ADF-F1 Use two screws. Screws Original delivery tray Connect the signal cable of the RDF or the ADF to the copier. 5–17 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 386: Machine Specifications Setting Mode (*5*)
ON/OFF of notation of U-size cassette paper size. If the machine is equipped with fax functions, go to H. “Fax Settings.” Otherwise, go to I. “Checking Copy Images.” 5–18 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 387: Fax Settings (For Machines Equipped With Fax Functions)
Connect the other end of the modular cord to the modular jack of the telephone line. 5–19 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 388 OK key. • 10 pps • Touch tone Press the 'Close' key several times to return to the Standard screen. 5–20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 389 NL adjustment. • To not continue on to adjust NL, press the Cancel key, and press the Reset key twice to end service mode. 5–21 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 391 3) Press the Test Shot key, place an original, and press the OK key. Try communications tests to check the operation and the images. 5–23 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 392: Checking The Copy Images
(Moire near the step edge of halftone bands may be ignored. Clean the area around the machine, and fill out the service sheet. 5–24 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 393: Shading Adjustment
START’ on the LCD to high- light. Press the OK key. • Shading will be executed. • Shading will end when ‘Now [END ]’ appears. 5–25 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 394 Copy Start key. • The copier will generate a test pattern. (You will use the Test Pattern later.) 5–26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 395 • The above ends PD auto- matic density adjustment; execute 200PWM density automatic adjustment. Face down, i.e., the printed side at the bottom. 5–27 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 396 • In photo mode, the white background must be free of multifeeder. fogging. (Moire around step edges around halftone bands may be ignored.) 5–28 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 398: Relocating The Machine
(Work in a group of two.) Lower the copier on the floor or on a desk. 5–30 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 399: Iv. Installing The Control Card V
2) Remove the screw from the face plate w. Figure 5-402 3) Remove the protection sheet from the display of the Control Card V. 5–31 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 400 Note 2: Check to make sure that the connector e for the printer is centered over the hole. Figure 5-406 Figure 5-404 5–32 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 401 8) Place the plastic sheet !2 in the hole in the control panel (used for the display of the Control Card V). Figure 5-408 5–33 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 402: Copy Data Controller-A1
If the Control Card V is to be used or if remote control only by the Copy Data Controller-A1 is to be used*, set bit 4 of the DIP switch (SW5) to OFF. Table 5-501 5–34 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 403 JB2) on the Copy Data Controller-A1 to suit Figure 5-505 the needs of the user. LED1 LED2 LED3 LED4 LED5 LED6 SW1 ON SW5 ON Figure 5-503 5–35 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 404 1 of the copier's rear cover. Figure 5-507 3) Fix the unit 6 in place on the copier's rear cover using four screws. Figure 5-506 Figure 5-508 5–36 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 405 LED2 LED3 LED1 LED2 LED3 LED4 LED5 LED6 LED4 LED5 LED6 SW1 ON SW5 ON SW1 ON SW5 ON Figure 5-512 Figure 5-510 5–37 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 406 8-4) To change to card input, press the 1 key Controller-A1. after MANAGE=ID has appeared; then, press key. MANAGE=CARD will appear. Code Input method Card Table 5-502 Figure 5-514 5–38 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 407 Set the DIP switch (SW1) of the Coy Data Controller-A1 as shown. (LED5 remains OFF.) Position 1, 2, 3 Table 5-504 5–39 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 409 SW1 ON SW5 ON DIP switch (SW1, SW5) on the Copy Data Controller-A1 appears. SW5-3 Figure 5-519 5–41 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 410 Controller-A1. (As necessary, use a relay 17) Check to make sure that the cable is not cable.) trapped by the casters of the copier or the sorter. 5–42 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 411: Scheculed Servicing Chart
CHAPTER 6 MAINTENANCE AND SERVICING PERIODICALLY REPLACED PARTS ..6-1 III. SCHECULED SERVICING CHART ..6-2 CONSUMABLES AND DURABLES ..6-1 SCHEDULED SERVICING......6-4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 413 Actual copies used for Manual feed separation pad FC1-9022-030 200,000 Pre-exposure lamp FG5-6297-000 200,000 Developing cylinder FG5-6222-000 400,000 100V FG5-8705-000 400,000 120V, 230V 6–1 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 MAY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 414 Clean the fixing/delivery assembly: • Fixing assembly inlet guide • Lower separation claw Provide scheduled servicing (p. 6-4) according to the number of copies made. 6–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 415 Record the final counter reading. Fill out the service book, and report to the person in charge. 6–3 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 MAY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 416: Scheduled Servicing
No. 1 through No. 3 mirrors Lens Original size sensor Dust-proofing glass Developing Developing roll assembly Fixing assembly Fixing assembly inlet guide Lower separation claw 6–4 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 417: General Timing Chart
COMPOSITE POWER SUPPLY ANALOG PROCESSOR CIRCUIT CIRCUIT DIAGRAM ......A-29 DIAGRAM..........A-20 LIST OF SPECIAL TOOLS ....A-37 LASER DRIVER CIRCUIT DIAGRAM ..A-24 SOLVENTS/OILS ........A-38 PICK-UP UNIT CIRCUIT DIAGRAM..A-26 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 419: A. General Timing Chart
Delivery reversing motor (M8) Delivery sensor (PS13) Counter (CONT1) Counter (CONT2) Feeding fan (FM1) Exhaust fan (FM2/FM3) Laser cooling fan (FM4) Electrical unit fan (FM5) P199-1 A–1 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 420: B. Signals And Abbreviations
EXHAUST FAN3 (FM3) DRIVE command FMD 4 FAN4 (FM4) DRIVE command FMD 5 FAN5 (FM5) DRIVE command FMD 6 FAN6 (FM6) DRIVE command A–2 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 425: Dc Controller Circuit Diagram
APPENDIX D. DC CONTROLLER CIRCUIT DIAGRAM DC Controller Circuit Diagram (1/13) A–7 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 438: Analog Processor Circuit Diagram
APPENDIX E. ANALOG PROCESSOR CIRCUIT DIAGRAM Analog Processor Circuit Diagram (1/4) A–20 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 442: Laser Driver Circuit Diagram
APPENDIX F. LASER DRIVER CIRCUIT DIAGRAM Laser Driver Circuit Diagram (1/2) A–24 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 445: Cassette Size Detection Circuit Diagram
APPENDIX H. CASSETTE SIZE DETECTION CIRCUIT DIAGRAM A–27 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 447: Composite Power Supply Circuit Diagram
APPENDIX J. COMPOSITE POWER SUPPLY CIRCUIT DIAGRAM Composite Power Supply Circuit Diagram (1/8) A–29 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 455: List Of Special Tools
A : Each service person is expected to carry one. B : Each group of five service persons is expected to carry one. C : Each workshop is expected carry one. A–37 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 456: Solvents/Oils
(low viscosity) assembly roller family) CK-0524 (100cc) bushing (FS2-1005- 000) Lubrication oil Lubricating: drive Silicone oil Tool No.: CK-0551 (20g) and friction parts A–38 COPYRIGHT © 1996 CANON INC. CANON GP215/200 REV.0 JULY 1996 PRINTED IN JAPAN (IMPRIME AU JAPON)
Page 457 Prepared by OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DEPT.1 OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIV. CANON INC. Printed in Japan REVISION 0 (JULY 1996) [26313/30809] 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146 Japan...
Page 458 This publication is printed on 70% reprocessed paper. PRINTED IN JAPAN (IMPRIME AU JAPON) 0796S2.82-1...

This manual is also suitable for:

Gp200

Canon GP215 Service Manual

Table of Contents

Chapter 1 General Description

Chapter 2 Copying Process

Chapter 3 Operations and Timing

Chapter 4 Mechanical System

Chapter 5 Installation

Chapter 6 Maintenance and Servicing

Appendix

Quick Links

Chapters

Related Manuals for Canon GP215

Summary of Contents for Canon GP215