Telemetry:voltage [Battery] - FUTABA T18SZ Instruction Manual

Telemetry: Voltage [Battery]
In this screen, the battery voltage is displayed.
In order to use this function, it is necessary to
connect External voltage connector of R7008SB ⇔
SBS-01V ⇔ Battery
SBS-01V measures two batteries. The power
battery connected to two lines is displayed on EXT-
VOLT. The battery for receivers connected to 3P
lines is displayed here.
● Tap the [Voltage] button in the Telemetry screen
to call the setup screen shown below.
●Return to
Linkage menu
Max. and min. values
s i n c e t h e p o w e r
was turned ON will
display.
↓ The "down" arrow
will indicate that an
alarm will sound when
the voltage drops to
below the setting.
Alarm is chosen from
Buzzer, Voice, and
Inhibit.
The ON/OFF switch
of Speech is chosen.
Alarm set
1. Tap to the ↓Alarm item, and it chooses
from Buzzer, Voice, and Inhibit.
2. W h e n n o t o p e r a t i n g v i b r a t o r , i t i s
"Vibrator" to Inhibit. Type1-3 will be
chosen if it is made to operate.
3. Tap to the Limit [4.0V] item .
4. Ajust the rate by "▼▼" "▼" "▲" "▲▲"
button.
Initial value: 4.0V
Adjustment range: 0.0V~100.0V
*When the screen is tapped for one second, the rate is
reset to the initial value.
5. To terminate the input and return to
the original state, push the HOME/EXIT
button.
*Refer to the manual of SBS-01V for the details of
wiring.
Displaying data from the receiver battery voltage
*SBS-01V must be installed in the aircraft.
In this screen, the battery voltage of a receiver is
displayed.
If it becomes higher or lower than the setting an
alarm and/or vibration will alert you.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH /T-FHSS mode can use all the telemetry
functions.
Vibrator is chosen from
type1-3, and Inhibit.
＜ Two examples of wiring are shown ＞
Two drive batteries are measured (R7008SB use)
Drive battery 1
（EXT Battery)
Drive battery 2
（EXT Battery)
Receiver battery
Two drive batteries and power supplies for servos are measured (R7008SB use)
*SBS-01V measures two voltage. One corresponds to high voltages, such as a drive battery,
with an EXT line. Another is a normal line and is measurement of the battery for receivers of a
line connected to 3P connector, or the battery for servos.
Drive battery 1
（EXT Battery)
EXT Line
Drive battery 2
（EXT Battery)
Power supplies
Switch
for servos
S.BUS2
●Battery voltage measurement for receivers [R7008SB use]
servos
●The drive battery 1 is measured in an EXT port [R7008SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
●The voltage for servos is measured in a power supply line [SBS-01V use]
Battery voltage
A setup of the
voltage on which the
alarm operates.
to S.BUS2
port
EXT Line Normal Line
R7008SB
●Battery voltage measurement for receivers [R7008SB use]
●The drive battery 1 is measured in an EXT port [R7008SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
to S.BUS2
Normal Line port
Another power
supply Hub
Receiver battery
＜ Linkage menu ＞
R7008SB
103