Sony HVR-V1U Service Manual page 202

12. Linearity Adjustment
Correct the linearity of AFE (analog Front End).
Subject Clear chart
(Color reproduction adjustment
frame)
Adjustment Page 6E
Adjustment Address F0 to F7
Note 1: If reading/writing data on pages 6E, set data: 06 to page:
0, address: 10, and then select pages: E. By this data set-
ting, the pages 6E can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to "00".
Note 2: Check that the data of page: 6, address: 02 is "00".
If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 2
3) REC FORMAT (Menu setting) ............................. HDV1080i
4) STEADY SHOT (Menu setting) ..................................... OFF
5) D. EXTENDER (Menu setting) ...................................... OFF
Address
F0 F1
Type
A 00 00
B E1 E1
C C2 C2
D A3 A3
E 83 83
F 80 80
G 80 80
Table 6-1-2
Adjusting method:
Order Page Address Data
1 0 01 01
2 0 10 0A
3 E
8C 01
(AE)
4 0 10 06
F
5 90
(6F)
F
6 91
(6F)
F
7 92
(6F)
F
8 93
(6F)
D
9 5E
(6D)
D
10 5E 5C
(6D)
HVR-V1J/V1U/V1N/V1E/V1P/V1C
F2 F3 F4 F5 F6
00 00 00 00 00
EE F2 F6 FA FC
DC E4 EB F3 F7
C9 D6 E1 EC F2
B7 C8 D6 E5 ED
A5 BA CB DE E8
92 AC C1 D7 E4
Procedure
Press PAUSE (Write) button.
Note down the data.
Note down the data.
Note down the data.
Note down the data.
Note down the data.
Press PAUSE (Write) button.
Order Page Address Data
11 0
12 6
13 6
14 6
15 6
16 6
17 6
18 0
D
19
(CD)
20 0
21 6
22 6
23 0
24 0
F
25
(AF)
26 0
F7
E
27 F0 to F7
(6E)
00
FD
28 0
F9
29 6
F5
30 6
F2
EE
31 1
EA
32
33
34 0
E
35 F0 to F7
(6E)
36 0
Note 3: For the bit values, refer to "6-4. SERVICE MODE", "4-
3. 3. Bit value discrimination".
Note 4: The upper two digits of the page: 1 displayed data of the
adjusting remote commander (RM-95).
1 : XX : XX
Read the "Data Section" of adjustment remote com-
mander (New LANC jig).
P : 01 a: XX d: XX
Note 5: Data is displayed in the signed chart form. (Data: FF
becomes –1.)
Note 6: If there are multiple types of which data is nearest to 0,
select the type in the center.
6-44
Procedure
10 00
CA 07
15 92
01 0B Press PAUSE (Write) button.
Check the data changes to
02
"01".
01 00 Press PAUSE (Write) button.
C9 10
10 0C
0E 0F Press PAUSE (Write) button.
10 00
14 87
9D 10
03 29
10 0A
Set the bit value of bit6 is "1",
1E
and press PAUSE (Write)
button. (Note 3)
10 06
From Table 6-1-2, set the type
A data, and press PAUSE
(Write) button.
10 00
01 0F Press PAUSE (Write) button.
Check the data changes to
02
"01".
Read the displayed data
(Note 4) and write it down.
For the type B to type G,
perform order 26 - 31, same
as type A.
Select the type of which data
read in the order 31 is nearest
to 0. (Note 5, 6)
10 06
Set the data of the type
selected in the order 33 and
press PAUSE button.
10 00
Displayed data
Data Section