Mirage 10000 User Manual

page of 136

/ 136
Bookmarks

Quick Links

Download this manual

,QWURGXFWLRQ

,QVWDOODWLRQ

6HWXS

2SHUDWLRQ

0DLQWHQDQFH

6SHFLILFDWLRQV

$SSHQGLFHV

NOTE: Due to continuing research, all information in this manual is subject to change without notice

3 6RIWZDUH 9HUVLRQ F

7DEOHRI&RQWHQWV

6HFWLRQ

&RQWHQWV

1.1

The Projector ....................................................................................................1-1

1.2

Components ......................................................................................................1-2

1.3

Purchase Record and Servicing.........................................................................1-2

2.1

Quick Setup.......................................................................................................2-1

2.2

Installation Considerations................................................................................2-3

2.3

Projector Position and Mounting ......................................................................2-9

2.4

Source Connections ........................................................................................2-14

2.5

Power Connection...........................................................................................2-21

2.6

Operating Orientation .....................................................................................2-21

2.7

Leveling ..........................................................................................................2-21

2.8

Zoom, Focus & Lens Offset............................................................................2-22

2.9

Serial Port Connections...................................................................................2-22

2.10

Keypad Protocols and Conversion ..................................................................2-26

3.1

Overview...........................................................................................................3-1

3.2

Projector Basics ................................................................................................3-1

3.3

Using the Keypad..............................................................................................3-4

3.4

Navigating the Menus .....................................................................................3-12

3.5

Using Inputs and Channels..............................................................................3-17

3.6

Adjusting the Image ........................................................................................3-22

3.7

Adjusting System Parameters and Advanced Controls ...................................3-30

3.8

3D Images .......................................................................................................3-47

3.9

Using Multiple Projectors ...............................................................................3-54

3.10

Error Conditions .............................................................................................3-55

4.1

Warnings and Guidelines ..................................................................................4-1

4.2

Cleaning ............................................................................................................4-3

4.3

Replacing Keypad Batteries..............................................................................4-3

4.4

Replacing the Lamp and Filter ..........................................................................4-4

4.5

Replacing the Lens............................................................................................4-9

4.6

Troubleshooting ..............................................................................................4-12

5.1

Specifications....................................................................................................5-1

Glossary ...........................................................................................................A-1

Keypad Reference ........................................................................................... B-1

Menu Tree........................................................................................................ C-1

Serial Communication Cables..........................................................................D-1

Throw Distance................................................................................................ E-1

Optional Input Modules ................................................................................... F-1

8 V H U V 0 D Q X D O

0LUDJH

8VHU V 0DQXDO

3DJH

LLL

Summary of Contents for Mirage 10000

Page 1 8 V H U V 0 D Q X D O 7DEOHRI&RQWHQWV 6HFWLRQ &RQWHQWV 3DJH ,QWURGXFWLRQ The Projector ....................1-1 Components ......................1-2 Purchase Record and Servicing.................1-2 ,QVWDOODWLRQ Quick Setup.......................2-1 6HWXS Installation Considerations................2-3 Projector Position and Mounting ..............2-9 Source Connections ..................2-14 Power Connection...................2-21 Operating Orientation ..................2-21 Leveling ......................2-21...
Page 2 The robust Mirage 10000 is built for frequent transport and quick installations, and is ideal for large audience venues such as simulations, theme rides and other entertainment attractions demanding effortless setup and brilliantly realistic 3D images.
Page 3 ,1752'8&7,21 +RZ 7KH 3URMHFWRU :RUNV Mirage 10000 accepts data/graphics and video input signals for projection on to front or rear flat screens. High brightness light is generated by an internal 1.9 kilowatt Xenon arc lamp, then modulated by three DMD (digital micromirror device) panels that provide digitized red, green or blue color information.
Page 4 6 H F W L R Q ,QVWDOODWLRQ 6HWXS This section explains how to install and set up the projector. If you are familiar with the projector and want to quickly set it up for temporary use, follow the Quick Setup instructions below. For a more complete setup, follow the instructions and guides covered in the remaining subsections.
Page 5 See 3.5, Using Inputs and Channels if you want to work with other source inputs or defined channels. Although the Mirage 10000 projector is engineered to deliver a stunning high ,QVWDOODWLRQ brightness quality output, the final display quality could be compromised if the &RQVLGHUDWLRQV...
Page 6 ,167$//$7,21 6(783 )LJXUH 'R QRW KRLVW E\ HQG KDQGOHV +RLVWLQJ You can use appropriate webbed strapping and hoisting/rigging :$51,1* equipment to lift the projector and/or 8VH VWUDSV RU FDEOLQJ install it as a permanently suspended ZLWK ORDG FDSDFLW\ DGHTXDWH IRU WKH installation.
Page 7 ,167$//$7,21 $1' 6(783 ,QVWDOODWLRQ 7\SH Choose the installation type which suits your needs: front or rear screen, floor mount or inverted mount. )URQW 6FUHHQ )ORRU 0RXQW ,QVWDOODWLRQ $'9$17$*(6 &216,'(5$7,216 (DV\ WR VHW XS 6KDUHV IORRU VSDFH ZLWK DXGLHQFH &DQ EH PRYHG RU FKDQJHG TXLFNO\ (DV\ WR DFFHVV )URQW 6FUHHQ ,QYHUWHG 0RXQW FHLOLQJ ,QVWDOODWLRQ $'9$17$*(6...
Page 8 )LJXUH $VSHFW 5DWLRV RI DQG choose a screen aspect ratio which is most appropriate for your projector—for the Mirage 10000, use a 4:3 screen. Ideally, to exactly fill a screen with an image, the aspect ratio of the screen 8VHU·V 0DQXDO...
Page 9 For example, standard video from a VCR has a 4:3 ratio (approximately), whereas a high resolution graphics signal typically has a 5:4 aspect ratio. By default, Mirage 10000 images will be as large as possible for the inherent aspect ratio of their source.
Page 10 ,167$//$7,21 6(783 )LJXUH %HWWHU 6FUHHQ 3ODFHPHQW Even with all lighting removed it is still possible that room reflections within the room can slightly degrade the image. Light from the projection screen should be absorbed by the ceilings, walls and floors so that it will not be reflected back to the screen.
Page 11 ,167$//$7,21 $1' 6(783 )LJXUH 6FUHHQ /RFDWLRQV IRU 0D[LPXP $XGLHQFH &RYHUDJH Installation type, screen type, and lighting all affect where the projector is positioned. 3URMHFWRU In addition, both throw distance (the distance between the projector and screen) and 3RVLWLRQDQG vertical position (the height of the projector in relation to the screen) must be 0RXQWLQJ determined for every new installation.
Page 12 ,167$//$7,21 6(783 9HUWLFDO +RUL]RQWDO of the projector in relation to the screen also depends on the 7+( 9(57,&$/ 326,7,21 3RVLWLRQ size of the screen and the lens type. Correct vertical position helps ensure that the image will be rectangular in shape rather than keystoned (having non-parallel sides) and that image focus and brightness both remain optimized.
Page 13 ,167$//$7,21 $1' 6(783 )LJXUH $YHUDJH 0D[LPXP 9HUWLFDO 2IIVHWV 1219,67$352 /(16(6 21/< NOTES: 1) For any projector, if you cannot raise or lower the image enough using mechanical vertical offsets, try adjusting V-Position in the Size and Position menu (see 3.6, Adjusting the Image) when displaying at less than the maximum size. 2) If the image becomes keystoned or exhibits uneven brightness, the projector may simply be too high or low in relation to the screen.
Page 14 ,167$//$7,21 6(783 6SHFLDO 0RXQWLQJ Note that projector can be rotated and mounted at any vertical angle—i.e., you can tilt the face of the projector up or down as much as desired for your installation. The side-to-side tilt, however, must not exceed 15° (see Figure 2.13). This limit ensures that the arc lamp in the projector operates properly and safely.
Page 15 ,167$//$7,21 $1' 6(783 The front panel of the projector provides standard input panels to which you may 6RXUFH connect a variety of sources. See Figure 2.14–the lower left area ( ) typically ,1387 &RQQHFWLRQV accepts an RGB signal from an external RGB source, or it can also be used for YPbPr signals or video sources.
Page 16 ,167$//$7,21 6(783 5*% 6LJQDOV provides 5 BNCs (connectors) for linking to a variety of sources. The typical ,1387 connection would be to an RGB source such as VGA, SVGA, XGA, Mac, PowerMac, DEC, Sun, SGI and others. This projector supports multiple sync types with RGB signals: sync-on-green, composite sync, and separate H &...
Page 17 ,167$//$7,21 $1' 6(783 <3E3U 6LJQDOV Connect a YPbPr signal (component video) to as shown in Figure 2.16. ,1387 &20321(17 9,'(2 )LJXUH &RQQHFWLQJ <3E3U 6LJQDO NOTES: 1) If, for some reason, the projector fails to recognize a YPbPr signal, specify this Color Space option within the Image Settings menu.
Page 18 ,167$//$7,21 6(783 69LGHR The optional video decoder input panel provides simultaneous connection of both a composite video source ( ) and an S-Video source ( ,1387 ,1387 If connecting an S-Video source, use the 4-pin mini DIN connector or the Y and C BNC connectors (luma and chroma) at do not use both as inputs.
Page 19 ,167$//$7,21 $1' 6(783 9LGHR /RRS 7KURXJK To loop a single incoming video signal input (connected at the optional video decoder) through to another projector or display device, use the empty connector(s) adjacent to this same input as described below. &RPSRVLWH 9LGHR /RRS 7KURXJK See Figure 2.19.
Page 20 ,167$//$7,21 6(783 )LJXUH &RQQHFWLRQV IRU 69LGHR /RRS 7KURXJK ([WUD 9LGHR If you want to use an extra video source in addition to the video source(s) connected at ² &20326,7( 25 69,'(2 connect either a Composite or S-Video source to as shown in ,1387 ,1387 ...
Page 21 ,167$//$7,21 $1' 6(783 “RBG” input module installed at —the optional HDTV Input Module used in ,1387 earlier projectors is not needed or recommended . 4) See Appendix F, Optional Input Modules for a brief description of each interface. You may wish to use one or more external Marquee Signal Switchers or a third party &RQQHFWLQJ D VZLWFKHU switcher in order to significantly increase the number of sources you can select.
Page 22 ,167$//$7,21 6(783 Plug the twist-locking 3-prong end of the integral line cord (30-amp, with L6-30 3RZHU plug) into an appropriate grounded AC source. Twist to secure. Input voltage to the &RQQHFWLRQ projector must be capable of supplying between 200 and 240 VAC, 50 or 60 Hz. The power source must be capable of supplying 2800 watts of power to the projector.
Page 23 ,167$//$7,21 $1' 6(783 Once the projector is properly set up and projecting an image, you are ready to make =RRP)RFXV /HQV quick adjustments of the motorized lens. Lens control is accessed by pressing the /HQV2IIVHW key on one of the keypads, which will display the Lens Control menu of options. NOTE: Refer to Section 3 if you need help in navigating the menu.
Page 24 ,167$//$7,21 6(783 )LJXUH 56 6HULDO &RQQHFWLRQ WR D &RPSXWHU 56 3RUWV Some computers can provide serial communications (often through a plug-in 56 adapter or external converter) rather than the more common RS-232. RS-422 communication has differential “transmits-and-receives” and is generally better suited for long distances than is RS-232 communication.
Page 25 ,167$//$7,21 $1' 6(783 and connect an RS-232 serial communication cable between the switcher and ,1387 the projector serial port labeled (refer back to Figure 2.22). The switcher 6:,7&+(5 communication link (permanently set at 9600 baud) enables you to access inputs connected to the switcher in the same manner as those connected directly to the projector.
Page 26 ,167$//$7,21 6(783 For either type of network, continue connecting projectors in this manner until you’ve reached the last projector in the chain, so that only the last projector has an empty , if applicable). See examples below. 56 287 56 3257 )LJXUH $VVRUWHG 1HWZRUNV Note that communication parameters such as baud rate must be set to match the...
Page 27 ,167$//$7,21 $1' 6(783 Each projector can be assigned a unique 3-digit projector number (for example, 001). 3URMHFWRU 1XPEHUV These numbers are necessary when you are working with multiple linked projectors, enabling you to direct commands to a certain projector rather than always broadcasting to the entire network.
Page 28 ,167$//$7,21 6(783 )LJXUH ,QGHSHQGHQW .H\SDGV DQG 3URMHFWRUV The standard IR remote keypad or the optional wired remote can be set to one of two 5HPRWH .H\SDG 3URWRFRO different protocols — “A” or “B”. To hard-wire a protocol to “A” or “B” in either ³...
Page 29 ,167$//$7,21 $1' 6(783 6WHS 6HW WKH -XPSHUV Set the jumpers as shown in Figure 2.31. Take care to refer to the correct part of the drawing — IR or wired (optional). Use tweezers or needle-nose pliers to remove and replace each jumper as necessary.
Page 30 ,167$//$7,21 6(783 6+257&87 0(7+2' You can also issue software protocol settings through the keypad. These software commands will be lost when the keypad is either unplugged or when a battery is removed — the keypad will revert back to the hard-wired jumper settings (see above) until you enter the software commands again.
Page 31 6 H F W L R Q 2SHUDWLRQ This section explains how to use the projector once it has been installed. Please read 2YHUYLHZ through these pages before using the projector for the first time. A good understanding of projector features and how to access them will help you to take full advantage of the capabilities of the projector within minutes.
Page 32 23(5$7,21 )LJXUH %DVLF 3URMHFWRU &RPSRQHQWV /HQV &RPSRQHQWV )HDWXUHV Accessed via the key on the keypad, the lens barrel of a 5(027( =220 motorized zoom lens (optional) rotates to adjust the size of the image at the current throw distance.
Page 33 23(5$7,21 Section 2, Installation and Setup for an illustrated explanation of offset ranges for all lenses. Ranges are also listed on page 5-1. Offsets cannot be adjusted manually. Closing the shutter blocks the lens internally and turns 5(027( &21752/ 6+877(5 the image to off.
Page 34 23(5$7,21 )LJXUH 5HDGLQJ WKH 6WDWXV /('V NOTE: A steady red power light accompanied by a coded pattern of red and yellow flashes from the status light indicates an internal system error. Consult the rear LCD display for an explanation, and see 3.10, Error Conditions. If the problem persists, contact a qualified service technician available through your dealer.
Page 35 23(5$7,21 The infrared (IR) sensors on the front and rear of the projector ,1)5$5(' 6(16256 receive infrared signals from the IR keypad for remote control of projector functions. For proper operation make sure that these sensors are not blocked. Emergency access for powering down the projector in the event of a +$5' 5(6(7 system failure.
Page 36 23(5$7,21 %XLOWLQ The built-in keypad is located at the rear of the projector. An LCD window above this keypad provides feedback regarding current status and activities of the projector. )LJXUH .H\SDG ,5 5HPRWH The IR Remote Keypad controls the projector by way of wireless communications from a battery-powered infrared (IR) transmitter.
Page 37 23(5$7,21 :LUHG 5HPRWH The wired remote keypad connects to the 3-pin XLR jack via a 50 ft. cable. It is ³237,21$/³ recommended when: the rear keypad is inaccessible the lighting conditions are unsuitable for proper IR transmission you want to use a separate keypad for each projector in a group NOTES: 1) For extra long distances and/or harsh environments, you may prefer to use an optional remote Two-Way Controller to control the projector.
Page 38 23(5$7,21 ,QSXW ,QSXW ,QSXW Press to select the source connected to on the projector (an optional ,1387 interface). This is the same as entering ,QSXW ,QSXW ,QSXW Press ,QSXW to select the source connected to on the projector (composite ,1387 ,QSXW video).
Page 39 23(5$7,21 functions are disabled. To leave standby press and hold 6WE\ again (or use 6WE\ Or simply press ([LW 0HQX 0HQX 0HQX Press 0HQX to display the Main menu. A list of several options appears for access to specific functions, such as Channel Setup or Image Settings. Press 0HQX again to remove all menus and return to presentation level.
Page 40 23(5$7,21 0XWH = turn the menu display on 0XWH = turn the menu display off 26' = turn the menu system on 26' = turn the menu system off &RORU &RORU &RORU Press to adjust the color saturation level, i.e. the amount of color in a video image.
Page 41 23(5$7,21 means that connected projector is listening; if there is no checkmark, you are communicating with a different projector. To use a specific projector, enter the 3-digit number assigned to the projector you (QWHU ([LW want to use. Press to select, press to cancel.
Page 42 23(5$7,21 Enable “Intelligent Lens System” to add the 4 lens ,17(//,*(17 /(16 6<67(0 positions—focus, zoom, horizontal and vertical offset—to the current channel settings recorded in projector memory (see 3.5, Using Inputs and Channels if you are unfamiliar with channels). This feature is particularly useful if you are using sources with radically different aspect ratios, such as anamorphic vs.
Page 43 23(5$7,21 NOTES: 1) With OSD on, you can still hide menus, error messages, slidebars, etc. 26' with the appropriate setting in the Preferences menu. 2) The status of the key is displayed in the LCD window at the rear of the projector. +HOS +HOS Press...
Page 44 23(5$7,21 NOTES: 1) If there is no signal present, all source-dependent adjustments are disabled. 2) After 15 minutes of inactivity, the projector leaves the menu system and returns to the presentation. 3) The Status menu is read-only. When finished with a function menu, do one of the following: ([LW Press to return to the previous screen...
Page 45 23(5$7,21 Most of the function menus allow you to change settings by using slidebars, 8VLQJ 6OLGHEDUV DQG 2WKHU &RQWUROV checkboxes, and pull-down lists. To select a slidebar, toggle a checkbox status, or view a pull-down list, do one of the following within the function menu: Enter the menu option number corresponding to the setting you wish to change (for example, press to select Vertical Stretch in the Size &...
Page 46 23(5$7,21 (QWHU Use the arrow keys to adjust a direct slidebar, or press and enter a specific (QWHU ([LW number from the keypad , then to save ( or to cancel). ([LW When you are done, press to save and return to your presentation. NOTES: 1) You can still adjust a direct slidebar as usual if the menu display is turned off (see 26'...
Page 47 23(5$7,21 To edit a highlighted character, use to scroll through (',7 $ &+$5$&7(5 the alphabet, numbers, spaces and punctuation available. When the character you need appears, press to select it— the cursor will move to the next character of current text, if present. Note that you can also enter a number directly from the keypad—it will be accepted and the cursor will move on.
Page 48 23(5$7,21 and is identified by a 2-digit number entered on the keypad. The first digit specifies the switcher (0-9), the second specifies the slot (1-9). Note that the projector is always considered “switcher #0”, and has only 4 “slots”. (;$03/(6 ,QSXW = use source connected to switcher #1, slot #3 ,QSXW...
Page 49 23(5$7,21 Shown at right is a sample channel list as &KDQ would be available from . This is typically called the channel list. &KDQ NOTE: The key may display a channel list or not, depending on what you have defined within the Preferences menu (see Preferences later in this section).
Page 50 23(5$7,21 :KDW &KDQQHOV All available channels are listed in the Channel Setup menu, which describes how $UH 'HILQHG 6R )DU" each channel can be accessed and which serves as the gateway for editing, copying and deleting channels. From the presentation 0HQX level press display the Main menu.
Page 51 23(5$7,21 )81&7,216 :,7+,1 7+( &+$11(/ 6(783 0(18 ³ To copy, delete or edit a channel, highlight the desired channel in the Channel Setup menu and do one of two things: )XQF Press if you want to copy the selected channel or delete this or other channels.
Page 52 23(5$7,21 NOTE: For any deletion, a confirmation box appears to make sure that you really want to delete. Select “Cancel” (default) if you don’t want to delete after all. (GLWLQJ D &KDQQHO 6HWXS The basic setups that describe how and where a channel can be accessed are listed in the Channel Setup menu.
Page 53 23(5$7,21 $872 6285&( If checked, (default), the projector can automatically locate this channel when an incoming input signal matches. If not checked, the projector can locate the selected channel only when it is &KDQ directly selected via on the keypad—and a change in input signal will not result in a channel change.
Page 54 23(5$7,21 ,PDJH 6L]H DQG 3RVLWLRQ The Size and Position menu allows you to increase or decrease the size of your image, change its proportion (aspect ratio), move the image to a specific area of the screen, and refine other related parameters.
Page 55 23(5$7,21 N 6(/(&7 ´12 5(6,=,1*µ to display the image in its native resolution, which may be smaller or larger than the projector’s own 1024 x 768 resolution. All Size, Vertical Stretch, H-Position, V-Position or Blanking values will change accordingly. For example, for a source with a native resolution of 800 x 600, “No Resizing”...
Page 56 23(5$7,21 9HUWLFDO 6WUHWFK Vertical stretch adjusts the height the image while keeping the width constant. Use Vertical Stretch to display data from the incoming signal in a different aspect ratio. Under some conditions, adjusting Vertical Stretch also adjusts keystone. NOTE: If Size 1000 (1000 = No Resizing) and Size Vertical Stretch value 1,000,000, adjusting Vertical Stretch also adjusts keystone simultaneously.
Page 57 23(5$7,21 1. Optimize Pixel Tracking and jot down the value. 2. Optimize Pixel Phase 3. If the image is still too noisy, return to Pixel Tracking and “mis-adjust” so that 2 vertical bands of noise appear, separated by a good center band.
Page 58 23(5$7,21 )LJXUH ,PDJH 6HWWLQJV 0HQX &RQWUDVW &RQW Press and adjust the slidebar.) 6+257 &87 “Contrast” increases or decreases the perceived difference between light and dark areas of your image (0-100). If contrast is set too high, the light parts of the image lose detail and clarity.
Page 59 23(5$7,21 'HWDLO Press d adjust the slidebar.) 6+257 &87 “Detail” adjusts the sharpness of the video image. Use until the display is as sharp as possible, keeping in mind that any level of detail above 3 (default) will increase the level of detail as well as introduce some level of noise in the image. Set below 3 to filter the signal and remove noise from a noisy source.
Page 60 23(5$7,21 9LGHR 6WDQGDUG The projector automatically detects the video standard present and displays the name of this standard here. Press to view or select a different video standard from a complete list available to the projector (some will appear disabled, depending on the current incoming signal).
Page 61 23(5$7,21 &RPPXQLFDWLRQV Use the checkboxes and pull-down lists in the Communications menu to alter the methods or types of communication to and from the projector. Refer to "Using Slidebars and Other Controls" subsection if you need help. Changes made to the Communications menu will be saved when you exit the menu.
Page 62 23(5$7,21 ,03257$17 .HHS DW ´ $ 25 % µ XQOHVV \RX DUH VXUH RI WKH FXUUHQW ,5 NH\SDG SURWRFRO NOTES: 1) The IR remote keypad for this projector is set at manufacture to "Protocol A". See 2.10, Keypad Protocols and Conversion for information about changing the keypad protocol.
Page 63 .H\VWRQH NOTE: Not available with 3D images processed with “Minimum Delay”. Adjust the keystone control if Mirage 10000 images appear keystoned in shape—that is, smaller at either the top or bottom rather than rectangular. The effect of keystone adjustment is similar to physically tilting the projector up or down in relation to the screen, and it affects all sources.
Page 64 23(5$7,21 NOTE: Keystone is enabled for a source only if Size is 1000 and Size Vertical Stretch is 1,000,000. Generally, set at 50 (default) to apply no keystone—if your projector is positioned with its lens surface parallel to the screen, images will be rectangular. If images are too narrow at the bottom, increase keystone.
Page 65 23(5$7,21 9LGHR 7HUPLQDWLRQ Enter a checkmark to terminate the video inputs 3 and 4 (75 The input should be terminated unless the signal loops through (continues) to another projector or display device, in which case only the last projector in the chain should be terminated. 0HQX 2SWLRQV In this submenu, choose the default location desired for on-screen menus.
Page 66 23(5$7,21 turn specific colors on or off to further pinpoint where a suspected problem may be occurring. Select this option to use a pull-down list of 7(67 3$77(516 ² all available internal test patterns. 7HVW NOTE: For quicker access from your presentation, use the 7HVW key to cycle through the patterns.
Page 67 23(5$7,21 By default (and during an “Auto :+(1 6+28/' , 86( 7+( ,1387 /(9(/6 0(18" Setup” from the Main menu), the projector automatically monitors image content and adjusts the Input Levels controls appropriately as described above—further adjustment is typically not required. NOTES: 1) This automatic adjustment requires at least 1 white pixel in the image.
Page 68 23(5$7,21 image, or if there is significant color drift. Delete the checkmark if the image is either sufficiently bright or overly bright. NOTE: The sync tip clamping option is not used for video sources or any RGB source with sync information on the video (e.g., sync-on-green). Select which color or colors you want to see, useful while working &2/25 (1$%/( ²...
Page 69 23(5$7,21 By default, the projector can utilize any of four calibrated factory-set color temperatures: 3200, 5400, 6500 or 9300 (expressed in degrees Kelvin). For most applications, these temperatures will display accurate and realistic colors from a variety of sources. They can be selected at any time in either the Image Settings menu or in the Advanced Color Temperature menu.
Page 70 23(5$7,21 selected from either the Image Settings menu or the Advanced Color Temperature menu as usual. You can re-define a “User” color temperature at any time using the Advanced Color Temperature menu. Select which color or colors you want to see, useful while working &2/25 (1$%/( ²...
Page 71 23(5$7,21 2. From the “Copy From” list, select the matching temperature labeled “Factory” (such as “Factory 5400K”). These are the calibrated color temperatures set at manufacture—they remain intact for the life of the projector. 3. The setups for the “User” color temperature you selected at the top of the Advanced Color Temperature menu will now be updated/replaced by those for the permanent factory calibrated temperature you selected in the “Copy From”...
Page 72 23(5$7,21 This control determines the projector’s processing route for the 352&(66,1* 02'( ² incoming signal. (default): The $872 projector will automatically select the correct processing mode according to what input signal it detects. Use “Auto” unless you want or need to override its performance and apply a specific mode instead.
Page 73 23(5$7,21 This control is most useful for smoothing out 027,21 ),/7(5 ² moving images from interlaced sources. In nearly all cases the proper Motion Filter setting is automatically determined according to the type of incoming source signal. However, if your source is noisy and/or inconsistent you may wish to “force”...
Page 74 23(5$7,21 value from 1-10, with “1” applying no filtering and “10” applying maximum filtering. High filtering levels will soften the image slightly, particularly evident along vertical edges. Vertical Filter: Select the amount of vertical filtering desired for the current source. Note that the default setting of “0” allows the projector to optimize the amount of vertical filtering according to the current source, and is the recommended setting for most situations.
Page 75 23(5$7,21 NOTES: 1) It is recommended that the Lamp Message checkbox remain enabled. 2) When a lamp warning message appears, press to temporarily cancel the message. The message will continued to appear upon power-up until you install a new lamp. to the number of hours you expect to log on the current lamp before /$03 /,0,7 replacing it.
Page 76 23(5$7,21 &+$1*( /$03 to record the serial number for a newly installed lamp. In the Lamp S/N window, use the number text entry keys to record the new lamp serial number, and press )LJXUH 5HFRUGLQJ WKH 1HZ /DPS 6HULDO 1XPEHU again to accept the change.
Page 77 23(5$7,21 projector model name and serial number. In addition, the Status menu identifies the current channel, switcher, slot and frequencies. to see additional Status information. )LJXUH 6WDWXV 0HQX 6$03/( A single projector can display 3D images as described below. In order to be ',PDJHV displayed and interpreted correctly in a typical 3D active stereo viewing environment such images usually require a specialized 3D source as well as the additional...
Page 78 5-wire RGB with separate H-sync and V-sync NOTE: Refer to 2.4, Source Connections for full details and illustrations. Most 3D sources are compatible with the Mirage 10000. However, because 3D signal formats currently available are optimized for display via older CRT (cathode ray tube) technology, it is possible that you may encounter an unusual source having a high pixel rate unsuitable for this projector.
Page 79 23(5$7,21 Typical hardware configurations for active and passive 3D systems using +DUGZDUH 5HTXLUHPHQWV “Minimum Delay” processing mode are shown in Figure 3.27 and Figure 3.28. Hardware descriptions follow the illustrations. )LJXUH 7\SLFDO ' &RQILJXUDWLRQ ZLWK $FWLYH *ODVVHV )LJXUH 7\SLFDO ' &RQILJXUDWLRQ ZLWK 3DVVLYH *ODVVHV : Signals from your 3D source (such as a graphics $335235,$7( ' 6285&( workstation) must be customized to precisely match the processing...
Page 80 23(5$7,21 synchronizing the left/right shutters in your 3D glasses to match the images displayed by the projector, you must connect a left/right inverter to the source. This ensures that shutter changes in the glasses allow each eye to receive the image data intended for it, regaining the 3D effect of the display.
Page 81 NOTE: The example in Figure 3.29 assumes that the first active line of your signal is displayed on the first line of the Mirage display panel rather than being repositioned higher or lower using the projector’s V-Position control.
Page 82 23(5$7,21 )LJXUH ([DPSOHV RI 3RRU DQG ,GHDO 6\QFKURQL]DWLRQ 2) “Dark Interval” projector control (note: not always required). For slower gating technologies, you may also need to artificially increase the amount of dark time between displayed frames so that shutters have even more time to open/close and each eye sees the full display intended for it (Figure 3.30B).
Page 83 Interval setting to “67” when using the 96 Hz source shown in Table 3.3, you will have 1 ms dark time between frames to accommodate the opening/closing of your 3D glasses. Refer to the following guide when 3D images displayed by Mirage 10000 do not ' 7URXEOHVKRRWLQJ appear as you expect: : Make sure your source signal is 96 Hz or higher.
Page 84 23(5$7,21 : Your video card’s minimum 12 ,0$*( -803< ,0$*( 25 12,6( $7 ,0$*( 723 timings for blanking and pulsed width are too slow for use with the projector. : You are not in 3D mode. Make :,7+287 */$66(6 , 6(( 21/< $ 6,1*/( ,0$*( sure “Minimum Delay”...
Page 85 23(5$7,21 To work with a single projector, press to display an editable window from each projector. Enter the three-digit number you have assigned to the projector you wish to control. All keypad commands will then affect this projector exclusively until you press again and enter a different number, or until you switch to broadcast mode (below).
Page 86 23(5$7,21 NOTE: Input signal messages appear on-screen only if Display Error Messages has been set to “Screen” or “All”. 1R 6LJQDO The message "No signal" appears when there is no signal detected at the selected input. Both HSYNC and VSYNC are inactive and the screen background is black. Connect or correct the signal, or select another input.
Page 87 23(5$7,21 System Warnings and System Errors, above). Acknowledge and clear the error with ([LW ([LW from presentation level, or try resetting the projector by powering it off and on again, cooling when necessary. Consult Table 3.4 and contact your dealer if the problem persists.
Page 88 23(5$7,21 7DEOH 6\VWHP (UURU &RGHV &RGH 'HVFULSWLRQ *(1(5$/ 6RIWZDUH EXJ &RQWDFW GHDOHUIDFWRU\ &5& HUURU LQ IODVK 520 'RZQORDG QHZ VRIWZDUH 5HSODFH ,30 $WWHPSWLQJ WR GRZQORDG FRGH ZLWKRXW EHLQJ LQ ERRW PRGH ,QYDOLG LQWHUUXSW 3RZHU RIIRQ ,I SHUVLVWV FRQWDFW GHDOHUIDFWRU\ /$03 %$//$67 8QDEOH WR WXUQ WKH ODPS RQ /DPS LV RYHUKHDWHG...
Page 89 6 H F W L R Q 0DLQWHQDQFH This projector is CSA approved and is designed for safe and reliable operation. :DUQLQJVDQG However, safe operation cannot be assured by design alone; installers, maintainers, *XLGHOLQHV and users must maintain a safe operating environment for the system. Please read through and understand the following warnings and guidelines promoting safe usage of the projector.
Page 90 0$,17(1$1&( /DPS DQG )LOWHU Do not operate the Xenon lamp for more than 1000 hours; risk of the lamp /$03 5HSODFHPHQW shattering increases as a result of changes in the quartz glass. Also, operation beyond 1000 hours significantly reduces brightness output. :$51,1* (YHQ FRRO ODPSV FDQ H[SORGH 'LUHFW ODPS ZLQGRZ $:$<...
Page 91 0$,17(1$1&( a radiator or heat register. The projector should not be placed in an enclosure unless proper ventilation is provided. In a stack, do not invert only a single projector. Never insert objects of any kind into the projector through the ventilation openings. They may touch dangerous voltages or short-out components resulting in a fire or shock hazard.
Page 92 0$,17(1$1&( )LJXUH 5HSODFLQJ .H\SDG %DWWHULHV NOTE: For this procedure you will need a “Roadie/Mirage 10000 Lamp and Filter 5HSODFLQJWKH Replacement Kit”. /DPSDQG)LOWHU The high brightness of your projector is provided by a 1.9 kilowatt Xenon lamp permanently mounted inside its own protective housing. When the bulb approaches 1000 hours of usage, this lamp module needs to be replaced.
Page 93 0$,17(1$1&( 67(3 7XUQ RII WKH SURMHFWRU Turn the projector off and allow the cooling fans to stop automatically before proceeding with Step 2. 67(3 8QSOXJ WKH SURMHFWRU When the cooling fans have stopped, unplug the projector. Allow additional time for the lamp to cool completely.
Page 94 0$,17(1$1&( 3XOO RXW ROG ODPS PRGXOH 67(3 Grasp the top and bottom handles of the lamp module and pull the module straight out of the projector (Figure 4.5). Pull firmly while keeping the assembly level. )LJXUH 3XOO RXW ROG ODPS PRGXOH 5HWXUQ ROG ODPS PRGXOH 67(3 All lamps returned to the manufacturer must be packed safely and securely in an...
Page 95 0$,17(1$1&( 67(3 ,QVWDOO ODPS EUDFNHW Set the lamp bracket into the slots on the side of the lamp compartment, making sure both ends seat securely at the bottom of the slots. Hand tighten the 2 knobs firmly so that the lamp is secured as far back into the projector as possible.
Page 96 0$,17(1$1&( It is a good idea to replace the 2 side filters whenever the lamp module is replaced (or )LOWHU 5HSODFHPHQW 3URFHGXUH more frequently if operating the projector in a dusty environment). These filters lie along the right side panel of the projector, running from the front edge to about 9 inches from the rear.
Page 97 0$,17(1$1&( A variety of lenses are available to accommodate different throw distances and 5HSODFLQJWKH specific types of installations. See page 5-1 for details. To change or install a lens, /HQV follow the steps below. 67(3 7XUQ RII WKH SURMHFWRU FRRO DQG XQSOXJ Before removing or installing a lens, turn off the projector and allow to cool for five minutes before unplugging.
Page 98 0$,17(1$1&( $'-867 7+( =220 Face the front of 5,1* the projector. On the lens, manually turn its textured zoom ring counter-clockwise as far as possible. Then reverse direction by approximately ½ inch. See right. Remove the lens cap. Plug in the projector and power up. /HQV Press to display the Lens Control menu.
Page 99 0$,17(1$1&( )LJXUH 7LJKWHQ WKXPEVFUHZV HTXDOO\ 67(3 5HSRVLWLRQ WKH SURMHFWRU Remove the lens cap and reposition the projector closer to or further from the screen as necessary for the screen and new lens type. For example, if using a 0.8:1 lens, throw distance should be roughly equal to 0.8 the screen width.
Page 100 0$,17(1$1&( 4. The batteries in the IR remote keypad may be weak. Refer to 4.3, Replacing Keypad Batteries for instructions. 5. The IR keypad may have been disabled by a change in protocol. See 2.10, Keypad Protocols and Conversion and 3.7, Adjusting System Parameters and Advanced Controls.
Page 101 0$,17(1$1&( 3. The lamp may have reached the end of its life. Check the “Lamp Hours” via the RS-232 request OSK" 6\PSWRP 7KH GLVSOD\ LV MLWWHU\ RU XQVWDEOH« 1. If the display is jittery or if it disappears and reappears erratically, check that the &$86( 5(0('< source is properly connected and that its signal is of adequate quality for ,QSXW...
Page 102 0$,17(1$1&( 2. The Size and Position options may be adjusted poorly for the incoming source signal. See 3.6, Adjusting the Image. 6\PSWRP 'LVSOD\ TXDOLW\ DSSHDUV WR GULIW IURP JRRG WR EDG EDG WR JRRG« 1. The operating temperature of the projector may be fluctuating. Watch that the &$86( 5(0('< projector is not located too close to heating/air conditioning vents.
Page 103 0$,17(1$1&( 4. The signal cables carrying the input signal may be of poor quality. Use only good quality signal cables. 5. The distance between the input source device and the projector may be too great. If the distance between the input source device and the projector is greater than 25 feet, signal amplification/conditioning may be required.
Page 104 6 H F W L R Q 6SHFLILFDWLRQV NOTE: Due to continuing research, specifications are subject to change without notice. 6SHFLILFDWLRQV 'LVSOD\ 3DQHO 5HVROXWLRQ DQG 5HIUHVK 5DWH Pixel format (H x V) on 3 DMD panels 1024 x 768 (XGA) Refresh rate 23.97 –...
Page 105 63(&,),&$7,216 $QDORJ 5*% DQG <3 U ,17(5/$&(' 25 352*5(66,9( 6&$1 )250$7 Horizontal frequency range 15 – 120 kHz * Vertical frequency range ** 23.97 –120 Hz Pixel clock rate 10 – 160 MHz Signal format Analog RGB or YP Active pixels per scan line (H) 640 –...
Page 106 63(&,),&$7,216 3RZHU 5HTXLUHPHQWV Voltage range (auto switching) 200 to 240 VAC continuous Line frequency 50 – 60 Hz nominal Max. inrush current 60 amps Max. current rating 14 amps @ 200V Max. power consumption 2800 watts Line cord rating 20 amp (use 20A or 30A plug) Line cord wiring: black or brown Live...
Page 107 63(&,),&$7,216 1RQRSHUDWLQJ (QYLURQPHQW Temperature -25°C to 55°C (-22°F to 120°F) Humidity (non-condensing) 0% to 95% 6WDQGDUG &RPSRQHQWV IR (infrared) Remote Keypad — includes batteries User’s Manual Warranty Registration Card 4 Eyebolts for hoisting: ½”-13 x 1½” 2SWLRQV $FFHVVRULHV Wired Remote Keypad 2-Way Controller IR Remote Sensor Alternate Throw Lenses...
Page 108 $ S S H Q G L [ $ *ORVVDU\ This appendix defines the specific terms used in this manual as they apply to this projector. Also included are other general terms commonly used in the projection industry. $FWLYH /LQH 7LPH The time, inside one horizontal scan line, during which video is generated.
Page 109 */266$5< &KHFNER[ A menu item that indicates whether an option is currently in effect (checked) or not (unchecked). &RORU 6KLIW A change in the tint of a white field across an image. &RORU 7HPSHUDWXUH The coloration (reddish, white, bluish, greenish, etc.) of white in an image, measured using the Kelvin (degrees K) temperature scale.
Page 110 ® channel. The Mirage 10000 has this capability, but it is not always known as ILS ,QSXW A physical connection route for a source signal, described by a 2-digit number representing 1) its switcher/projector location and 2) its slot in the switcher/projector.
Page 111 */266$5< /RRSWKURXJK The method of feeding a series of high impedance inputs from a single video source /RRSWKUX with a coaxial transmission line in such a manner that the line is terminated with its characteristic impedance at the last input on the line. /XPHQ The unit of measure for the amount of visible light emitted by a light source.
Page 112 */266$5< 5HVROXWLRQ SURMHFWRU The maximum number of pixels that the projector can display horizontally and vertically across an image, such as 1024 x 768 (called XGA). 5HWUDFH 7LPH The minimum time required for a CRT projector to move the position of the scanning +RUL]RQWDO spot from the right edge to the left edge.
Page 113 */266$5< "Separate sync" or "H.SYNC and V.SYNC": the horizontal and vertical components of the sync are on two separate cables. 6\QF :LGWK The duration of each sync pulse generated by a computer. The sync width is part of the blanking time. 77/ 9LGHR A type of RGB video with digital characteristics.
Page 114 $ S S H Q G L [ % .H\SDG5HIHUHQFH )LJXUH % .H\SDG 0LUDJH 8VHU·V 0DQXDO...
Page 115 $ S S H Q G L [ & 0HQX7UHH 0LUDJH 8VHU·V 0DQXDO &...
Page 116 0(18 75(( 0LUDJH 8VHU·V 0DQXDO &...
Page 117 $ S S H Q G L [ ' 6HULDO&RPPXQLFDWLRQ&DEOHV When connecting a projector to a computer, another projector, or a Marquee Signal Switcher, use the appropriate serial communication cabling as illustrated. For all connections, make sure to use high quality shielded cabling. 0LUDJH 8VHU·V 0DQXDO...
Page 118 6(5,$/ &20081,&$7,21 &$%/(6 0LUDJH 8VHU·V 0DQXDO...
Page 119 6(5,$/ &20081,&$7,21 &$%/(6 0LUDJH 8VHU·V 0DQXDO...
Page 120 6(5,$/ &20081,&$7,21 &$%/(6 0LUDJH 8VHU·V 0DQXDO...
Page 121 $ S S H Q G L [ ( 7KURZ'LVWDQFH &DOFXODWLQJ 7KURZ 'LVWDQFH The larger the image needed, the greater the distance required between the lens and screen. Correct throw distance depends on the screen width and lens throw ratio—once you know what is present, you can use the appropriate formula provided in this appendix to calculate the precise throw distance for your application.
Page 122 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 123 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 124 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 125 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 126 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 127 7+52: ',67$1&( 0LUDJH 8VHU·V 0DQXDO...
Page 128 $ S S H Q G L [ ) 2SWLRQDO,QSXW0RGXOHV There are many optional input modules and accessories currently available for this projector. Contact your dealer for a complete and up-to-date listing. The Marquee Signal Switcher is a rack-mountable signal selector which can greatly Marquee 6LJQDO 6ZLWFKHU increase the number of analog sources (inputs) available to the projector.
Page 129 237,21$/ ,1387 02'8/(6 )HDWXUHV ¡ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate horizontal and vertical sync), up to 500 MHz bandwidth ¡ BNC connectors for RGB signal inputs NOTE: The audio connectors are not functional. Connect audio to an external audio system.
Page 130 237,21$/ ,1387 02'8/(6 &RPSRVLWH 69LGHR The Composite/S-Video Input Module may be installed in this projector, a Marquee ,QSXW 0RGXOH Signal Switcher or a Marquee Case/Power Supply. The module receives either [[ composite video or S-video input signals from tape or disk players (do not connect both types of signals simultaneously).
Page 131 237,21$/ ,1387 02'8/(6 '9,')3 ,QSXW 0RGXOH The DVI/DFP Input Module can be installed in the projector to display digital video [[ input signals conforming to the DVI (Digital Visual Interface) standard (single- channel) or the DFP (Digital Flat Panel Port) specification. )HDWXUHV ¡...
Page 132 237,21$/ ,1387 02'8/(6 ,1387 6HULDO 'LJLWDO ,QSXW 0RGXOH The Serial Digital Input Module (SDI) can be installed in the projector at [[ where it accepts a serial digital 4:2:2 component video signal (YCbCr) via a single 6(5,$/ ,1 6(5,$/ 287 BNC connector.
Page 133 ,QGH[ Blacklevels and Drives, 3-37 Blanking, 3-27 Brightness Key, 3-10, 3-28 Brightness Specification, 5-1 Broadcast Keys, 3-33 and Clamp Tip control, 3-54 Broadcasting, 3-11, 3-55 and Color Artifacts, 3-52, 3-54 and Cross-Talk, 3-50, 3-53 and Dark Interval, 3-52 and IR Emitter, 3-50 and Minimum Delay, 3-54 Calibrate Lens, 3-46 and Pixel Tracking, 3-48...
Page 134 ,1'(; Loop-Through, 2-16 Contrast Key, 3-10, 3-28 Contrast Ratio, 5-1 Image Adjustments, 3-23 Custom Sizing, 3-24 Image Orientation, 2-19 Image Settings, 3-27 InMenu Checkbox, 3-22 Input Connection, 2-1, 2-12 Dark Interval, 3-50, 3-52 Definition of, 3-17 Decoder AGC. See Auto Gain Control Selecting/switching, 3-18 Decoder Luma Delay, 3-41 Selection, 2-2...
Page 135 ,1'(; Lamp Counter, 4-4 Horizontal, 2-10 Lamp History, 3-45 Vertical, 2-9 Lamp Hours, 3-44 Optional Input, 2-17 Lamp Limit, 3-45 Options/Accessories, 5-4 Lamp Menu, 3-44 OSD Key (On-Screen Display), 3-12 Lamp Message, 3-44 Lamp Modes Max Brightness, 3-45 Power, 3-45 Pixel Key, 3-11 Lamp Replacement Pixel Phase, 3-26...
Page 136 ,1'(; Shutter Key, 3-12 Toggle Keys, 3-9 Size and Position, 3-24 Troubleshooting, 4-11 Sizing, 3-24, 3-25 Two-Way Controller, 3-7 Slidebar Adjustment, 3-15 Slidebars "Direct", 3-15, 3-23 Using, 3-15 User Color Temperatures, 3-40 Slidebars, Display of, 3-34 Slidebars, Double, 3-15 Slot, 3-22 Source VCR Checkbox, 3-41 Connection, 2-1...

Mirage 10000 User Manual

Quick Links

Related Manuals for Mirage 10000

Summary of Contents for Mirage 10000